• Journal of Korean Society of Water and Wastewater
• /
• v.24 no.4
• /
• pp.433-442
• /
• 2010

BER at different packing ratios of bio-ring media(BRM) was tested to investigate the effect of varying hydraulic retention time (HRT) and current density on the nitrate removal and current efficiency. In the preliminary batch mode experiment of BERs, current density was applied at 2.0 A/$m^2$, 4.0 A/$m^2$, 4.8 A/$m^2$, which correspond to the designation of reactor #1, #2, #3, respectively. The reactor #2 showed a highest nitrate removal rate of 162.0 mg $NO_3{^-}$-N/L/d, and the kinetics of nitrate removal rate was defined as the Zero order reaction. In the primary experiment of BERs, four BERs packed with BRM were operated in varying HRT and current, and the packing ratios of reactor #1, #2, #3 and #4 were 0%, 8%, 16%, 24%. respectively. This results of the experiments indicated that the nitrate removal rate and current efficiency were increased significantly cause of growing of autotrophic denitrification microorganisms on the surface of cathode and media by increasing of the current density and decreasing of HRT. However, The decreasing of nitrate removal rate and current efficiencies were observed in the condition of HRT of 5.25 hr and 4.8 A/$m^2$ of current density. With more increasing current density and decreasing of HRT, the hydrogen inhibition occurred at the surface of cathode. Moreover, nitrate removal rate by autotrophic denitrification microorganisms attached on the media surface was observed to be limited by no longer increasing dissolved hydrogen concentration of each reactor. In conclusion, the highest nitrate nitrogen removal and current efficiency could be achieved when the BER was operated at the conditions of 7 hr HRT, current density of 4.0 A/$m^2$, and 16% packing ratio. And it was found that the amount of nitrate removal by microorganisms attached on the surface of cathode and media (BRM) was 178.2 mg/L and 52.2 mg/L respectively. and the amount of nitrate removal per MLVSS was 0.435 g $NO_3{^-}$-N/g $MLVSS{\cdot}d$ and 0.336 $NO_3{^-}$-N/g $MLVSS{\cdot}d$.

• Culinary science and hospitality research
• /
• v.17 no.3
• /
• pp.172-180
• /
• 2011

This study explores the quality characteristics of white pan bread added with perilla leaf powder, and the results are as follows. The WRC(water retention capacity) of PLP (perilla leaf powder) added to the bread dough increased as the addition increased, and the initiation temperature during the rapid visco analysis (RVA) increased with more additions, showing significant differences. The highest and the lowest viscosity of the sample decreased as the powder added increased. The brightness(L value) of the bread without the powder was the highest, and the redness (a value) and the yellowness (b value) showed significant differences among the samples. Hardness increased showing significant differences among the samples as the powder added increased Chewiness was the highest but preference value was the lowest in the sample with 7% of the powder. The lowest score was shown in the color of the sample with the most PLP added. Flavor was the lowest of 4.93 in the comparison sample without the leaf powder added while bitter taste scored the highest of 5.21 in the sample of 3% powder added. It was also the highest in overall acceptance while the sample with the most powder showed the lowest of 4.03. From these results, it can be said that the preference of bread with PLP seems to decrease when more than 5% of PLP is added.

• Asian-Australasian Journal of Animal Sciences
• /
• v.22 no.8
• /
• pp.1180-1185
• /
• 2009

Two experiments were carried out to study the effects of dietary energy level on nutrient digestion, nitrogen (N) utilization, growth performance, insulin-like growth factor-I (IGF-I), and insulin-like growth factor binding protein-3 (IGFBP-3) in plasma, liver and longissimus dorsi muscle in growing-finishing pigs. In experiment 1 (Exp 1), 15 castrated male pigs (Duroc${\times}$Landrace${\times}$Large White) (Body weight, BW, 55.6${\pm}$1.8 kg) were divided into three groups and fed rations containing 13.33, 14.87 and 17.35 MJ digestible energy (DE)/kg as treatments I, II and III, respectively, using soybean oil as an energy source. The experiment lasted 8 days and faecal and urinary samples were collected during the last 3 days. The results showed that the digestibility of dry matter (DM), energy and N was increased from treatments I to III (p<0.01). N-retention and N-retention rate were not influenced by dietary DE level (p>0.05). In experiment 2 (Exp 2), 36 female pigs (Duroc${\times}$Landrace${\times}$Large White) (BW 41.5${\pm}$3.8 kg) were divided into three groups. The pigs were fed with the same three rations used in Exp 1 for 60 days. At the end of Exp 2, eight pigs were selected from each group for blood sampling and 4 pigs for slaughter trial. The results indicated that average daily feed intake (ADFI) and N-intake were significantly decreased (p<0.01), and DE intake (p<0.01) and average daily gain (ADG) (p<0.05) were increased. IGF-I and IGFBP-3 in plasma were increased (p<0.05). No significant differences in IGF-I and IGFBP-3 in liver and longissimus dorsi muscle were found between different treatments. It was concluded that higher dietary DE level improved nutrient digestibility, ADG and feed/gain ratio when soybean oil was used as an energy source in the ration of growing-finishing pigs. No significant differences were found in Nretention and IGF-I and IGFBP-3 in liver and longissimus dorsi muscle between different treatments.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.3 no.3
• /
• pp.117-127
• /
• 1983

An experimental research was performed employing the two stage anaerobic digestion of the mixture of the nightsoil and septic tank sludge to determine the effects of various hydraulic retention time of the digestion on chemical characteristics and treatment effeciency, thus determining the proper retention time. Results of the research are as follows, 1. Volatile-acid decreased as HRT increased. 2. Alklinity and ammonia-N tended to increase as HRT increased as did pH values, however, were observed to be constant at higher HRT values than 15 days. 3. The removal efficiencies of TBOD, TCOD and VS increased as HRT increased. 4. The removal efficiency of volatile solid decreased as VS loading increased. 5. It was observed that the rates of gas production were: 0.33 with HRT of 5 days, 0.58 with HRT of 15 days and $0.57m^3/kg$ VS fed/day with HRT of 25 days respectively. It is believed that the highest rate of gas production was at HRT of 15 days. 6. The sludge settling experiment showed that the minimum settling time required to ensure the desired underflow concentraton was estimated to be 8.6 days.

• Korean Journal of Soil Science and Fertilizer
• /
• v.41 no.4
• /
• pp.273-278
• /
• 2008

This study was carried out in order to test unsaturated hydraulic conductivity estimation of van Genuchten's and Campbell's models using one-step outflow method through Tempe pressure cell. The undisturbed soil cores (columns) were taken from Ap1, B1 and C horizons of Songjeong series (the fine loamy, mesic family of Typic Hapludults). After the saturated hydraulic conductivity Ks of the cores was determined by constant head method, water outflow rate and retentivity of cores were measured in Tempe pressure cell. Fitted curves by models accorded to measured data except for both end of pressure range. In near-saturated condition, measured water retention characteristics showed a relatively better fitness with Campbell's model than van Genuchten's. The soil unsaturated conductivity estimated by Campbell's model was higher than by van Genuchten's. In Ap1 and B1 horizon, the soil unsaturated conductivities obtained by one-step outflow method went between van Genuchten's and Campbell's hydraulic functions, slightly closer to van Genuchten's. In C horizon, van Genuchten's model had better fitness with the one-step outflow data. Consequently, van Genuchten's model generally had better fitness with measured hydraulic conductivity than Campbell's model at the soil water potential range of -10~-75 kPa, especially in C1 horizon. In near-saturated condition, Campbell's model could be thought as relatively accurate hydraulic model, because of the better fitness of Campbell's model with soil water retention data than van Genuchten's model.

• Korean Journal of Environmental Agriculture
• /
• v.2 no.1
• /
• pp.24-29
• /
• 1983

The effects of temperature on the uptake of $^{137}Cs$ from seawater and on the retention after its uptake by the clam Cycling sinensis was investigated under laboratory conditions. The clams exhibited a greater bioaccumulation of $^{137}Cs$ in $25^{\circ}C$-acclimated animals than those acclimated at $15^{\circ}C$. The viscera of the clams reached the highest bioconcentration factor after 14 days uptake from seawater, but the tissue distribution pattern of $^{137}Cs$ was little influenced, if any, by the uptake temperature. The uptake rate slightly decreased with an increase of temperature in order of $10^{\circ}C$. The radionuclide accumulated in clams was released again in a radionuclide-free seawater according to a two-exponential compartment model. A temperature increase of $10^{\circ}C$ reduced the biological half-life of the long-lived component with a factor of about two, whereas it caused no change in the short-lived component.

• Applied Biological Chemistry
• /
• v.43 no.2
• /
• pp.116-123
• /
• 2000

A numerical model of three-dimensional soil water distribution for drip irrigation management under cropped conditions was developed using Richards equation in Cartesian coordinates. The model accounts for both seasonal and diurnal changes in evaporation and transpiration, and the growth of plant root and the shape of root zone. Solutions were numerically approximated using the Crank-Nicolson implicit finite difference technique on the block-centered grid system and the Gauss-Seidel elimination in tandem. The model was tested under several conditions to allow the flow rates and configurations of drip emitters vary. In general, simulation results agreed well with experimental results and were as follows. The velocity of soil-water flow decreased drastically with distance from the drip source, and the rate of expansion of the wetted zone decreased rapidly during irrigation. The wetting front of wetted zone from a surface drip emitter traveled farther in vertical direction than in horizontal direction. Under this experimental weather condition, water use efficiency of a drip-irrigated apple field was greatest for 4-drip-emitter system buried at 25 cm, resulting from 10% increase in transpiration but 20% reduction in soil evaporation compared to those for surface 1-drip emitter system. Soil moisture retention curve obtained using disk tension infiltrometer showed significant difference from the curve obtained with pressure plate extractor.

• Applied Chemistry for Engineering
• /
• v.27 no.6
• /
• pp.653-658
• /
• 2016

In this work, we developed a synthetic method for preparing one-dimensional $MnO_2$ nanowires through a hydrothermal method using a mixture of $KMnO_4$ and $MnSO_4$ precursors. As-prepared $MnO_2$ nanowires had a high surface area and porous structure, which are beneficial to the fast electron and ion transfer during electrochemical reaction. The microstructure and chemical structure of $MnO_2$ nanowires were characterized by scanning electron microscopy, transmission electron microscopy, X-ray photoelectron spectroscopy, X-ray diffraction, and Brunauer-Emmett-Teller measurements. The electrochemical properties of $MnO_2$ nanowire electrodes were also investigated using cyclic voltammetry and galvanostatic charge-discharge with a three-electrode system. $MnO_2$ nanowire electrodes showed a high specific capacitance of 129 F/g, a high rate capability of 61% retention, and an excellent cycle life of 100% during 1000 cycles.

• The Journal of Korean Academy of Prosthodontics
• /
• v.43 no.1
• /
• pp.15-29
• /
• 2005

Statement of problem. The adjustable dental impression trays were made for being adjusted their width automatically along the width of dental arch. Purpose. The purpose of this study was to investigate the best retentive form of adjustable dental impression tray, and so to make it a more satisfactory product. Material and methods. The eight pairs of adjustable trays were made of ABS(acrylonitrile butadiene styrene) with different distribution of holes and with or without the rim on the border area of them. The experiment was done with the horse-shoe shaped metal plate to pull out the set impression body from the tray, and the tray jig which was made for holding the tray on a lower part of Universal Testing Machine(UTM, Zwick Z020, Zwick Co., Germany). After the impression in the tray was allowed to set four minutes, a tensile force was applied at right angles to the tray which had been previously seated on the jig. The force was applied to measure a maximum retentive force by use of a UTM at a constant strain rate of 100mm per minute. A 2-factor analysis of variance (p<.05) was used to determine whether differences existed among distribution of retentive holes and between rim existing and not. Results. 1 The retentive force of the upper and lower resin tray with 2mm holes on the tray border was highest(25.83/24.98kg). (p<.05) 2. As the tray had more retentive holes, it was less retentive. 3. There was no significant difference in the retentive force of the varied hole intervals in the case of distributing all the area. (p>.05) 4. The rimless trays were more retentive generally, than the rimmed trays except 2 case: upper tray group-all area / 2 mm, intervals and lower tray group-margin only / 2 mm, intervals.(p<.05) 5. Most of the adjustable trays were showed higher retentive force than perforated metal tray except the lower group that perforated on the all area at intervals of 2 mm.

• Journal of the korean academy of Pediatric Dentistry
• /
• v.32 no.2
• /
• pp.284-292
• /
• 2005

The aim of this study was to identify and quantify the major or detectable monomers released from any of five commercially-available, light-cured pit and fissure sealants with three different light sources : conventional halogen light curing unit, plasma arc light curing unit and LED curing unit. After curing, specimens were immediately immersed in distilled water for different time intervals. The time related release of monomers were analyzed by high performance liquid chromatography(HPLC). Identification and quantitative analysis of monomers were performed by the comparison of the elution time and the absorption peak height of the eluates with those of the authentic sample. The result of this study can be summarized as follows. 1. Standard solution peaks with retention times of 2.3, 3.2, 5.6, 6.5, 10.4 minutes were identified as BPA, TEGDMA, UDMA, Bis-GMA, Bis-DMA, respectively. 2. None of the chromatograms of the tested sealants displayed peaks with the same retention time as that of the standard solution, except for TEGDMA. 3. The highest release rate of TEGDMA was observed during the 12hr period for all samples and declined thereafter. 4. The elution of TEGDMA from curing with Halogen curing unit for 20 second and LED for 10 second was less than that resulting from curing with Plasma arc for 3 second. 5. TEGDMA was detected at much lower levels in eluates from the Pit & Fissure $Sealant^{TM}$ than other sealants. The elution of TEGDMA from the $Helioseal^{(R)}$ F cured with Halogen light curing unit, the $Concise^{TM}$ cured with Plasma arc curing unit and the $Teethmate^{(R)}$ F-1 cured with LED curing unit were higher than other sealants.