• Nuclear Engineering and Technology
• /
• v.41 no.2
• /
• pp.179-186
• /
• 2009

This paper presents a thermal creep test under internal pressure and post-test characterization performed on high burnup (68 MWd/kgU) ZIRLO. This research has been done by the CSN, ENRESA, and ENUSA in order to investigate the behavior of advanced cladding materials in contemporary PWRs at higher burnup under dry cask storage conditions. Also, to investigate the hydride reorientation, the cool-down of the samples after the test has been done in a coordinated manner with the internal pressure. The creep results obtained are consistent with the expected behavior from reference CWSR material, Zr-4. During the test, the material retained significant ductility: one specimen leaked during the test at an engineering strain of the tube section of 17%; remarkably, the crack closed due to de-pressurization. Although significant hydride reorientation occurred during the cool-down under pressure, no specimen failed during the cool-down.

• Journal of Advanced Marine Engineering and Technology
• /
• v.21 no.5
• /
• pp.512-521
• /
• 1997

This paper deals with an evaluation of the residual stress due to shot peening induced in a car¬burized gear tooth and its application to the fatigue crack propagation problem. The residual stress is estimated based on the assumption that the main cause of residual stress is the volume difference between the case and core due to martensitic transformation in cooling, and the influ¬ence of both the reduction of retained austenite and the strain in the surface layer induced by shot peening are considered. The reliability of the method is examined by comparison with stresses measured by the X-ray diffraction method. The stresses intensity factors are computed by the influence function method and the reduction of the factor due to the residual stress is demonstrat¬ed and discussed based on the fracture mechanics.

• Journal of the Korean Society for Heat Treatment
• /
• v.27 no.2
• /
• pp.79-89
• /
• 2014

The effect of carbon on the microstructure and texture of low carbon steels was investigated in a series of 1.6 Mn-0.3Cr-0.2Mo-0.001B steels with carbon ranging from 0.021 to 0.048%. Intensity of {111} orientation increased with decreasing the carbon content, resulting in the increase in $r_m$ value. The highest $r_m$ value of 1.30 was obtained in 0.021%C steel annealed at $820{\sim}850^{\circ}C$ according to the typical galvannealing heat cycle. Martensite volume fraction was not substantially affected by the annealing temperature. It was found that the fine and uniformly distributed martensite particles which were present in amounts of about 5% volume fraction were desirable for the highest $r_m$ value. The other factor affecting the high $r_m$ value was the preferred epitaxial growth of retained ferrite with {111} orientation into austenite during cooling.

• Journal of Life Science
• /
• v.5 no.2
• /
• pp.57-62
• /
• 1995

Casein or soybean protein was subjected to there action with caffeic acidtyrosinase system at 30-35$\circ$C, pH 6.8 with aeration for 5hr. The resulting brown proteins were washed with acetone until the washings were on longer colored. However, modified protein still retained a light brown. The effects of the modified proteins and brown compounds on male Wistar strain rats were studied by pair-feeding of a cholesterol-free diet for 14days. Significant decrease in protein digestibility for the rats fed with the modified proteins were observed. Weight gain and protein digestibility were not influenced by feeding brown compounds, but the feeding of brown compound from casein caused an enlargement of caecum. The concentrations of serum cholesterol and triglyceride in the rats fed with modified proteins and brown compounds were mostly unchanged against the rats fed with untreated proteins. These results suggest that the decrease in protein digestibility induced by enzymic browning-reaction did not cause the decrease in concentration of serum cholesterol.

• 한국초전도학회:학술대회논문집
• /
• v.10
• /
• pp.221-225
• /
• 2000

The effect of twisting on the microstructural evolution and critical current of BSCCO superconductor tape has been evaluated. Twisting pitches of the tapes are in the range of 8-70 mm and uniformly deformed. The critical current of twisted tape was dependent on the twist pitch. Specifically, it was observed that the critical current decreased with decreasing twist pitch, and only 50% of critical current was retained when the tape was twisted to a pitch of 8 mm. This reduction of the critical current may be related to the interface irregularity, smaller grain size, worse texture and the presence of cracks due to the induced strain during the twisting processing.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.18 no.12
• /
• pp.3227-3235
• /
• 1994

This paper deals with an evaluation of the residual stress due to shot peening induced in a carburized gear tooth and its application to the fatigue crack propagation problem. A practical method is proposed on the basis of the assumption that the residual stress is caused by the difference of volume expansion in the case and the core, and the influence of both the reduction of retained austenite and the strain due to shot peening are considered. The evaluated residual stress is close to the measured stress, though the surface stress is rather overestimated. The stress intensity factor is computed by the influence function method, and it is shown that the factor is decreased by the residual stress in shot peened gear tooth. The shot peening is fairly effective to the reduction of fatigue crack growth rate. The crack propagation is simulated and the resistance due to shot peening is quantitatively demonstrated and discussed.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.16 no.8
• /
• pp.1451-1457
• /
• 1992

In hot strip rolling, the thickness of strip cannot be retained uniform by several irregular parameters. It has been shown that the load distribution can affect only a small fraction of the excess strip crown, whereas the thermal effects of working roll are the major reason on large changes in the strip center crown during hot rolling. In this study, the temperature distribution of working roll is represented by fourier series expansion. The analytical solution of the resulting thermo-elasticity problem is obtained by love's strain function. The results which are compared with those of the finite element method show good agreements.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.28 no.2
• /
• pp.63-73
• /
• 1986

The model was developed by applying the principles of Bacot and Vidal to measure the behavior of deformation of the reinforced earth wall, and various tasts were performed by using the plastic fabric filter and the galvanized steel plate as a strip. The results obtained are as follows; 1. When the reinforced earth wall is deformed by the load, the strip is completely reinforced by the backfill materials and changed to the rigid block state, under the state of failure which permits sliding only, the next theoretical equation is formed. (H/L) . tan$\theta$ [cosO-sinOtanO] =2sinO[tan($\theta$ +0) +tanO] 2.The degree of the mutual reinforcement of the backfill material and the strip depend on the physical characteristics of the each material especially the angle of shearing resistance of the backfill material is desirable over 20$^{\circ}$ and, if it is over 400, its function could be a maximum. 3.The distribution of the maximum tensile strain of the reinforcement is changing with the height of reinforced earth wall, and when the height from bottom of the reinforced earth wall is 1.85 to 3. 35m, the maximum tensile strain appears at 2m from the skin element. The maximum tensile strain is increased by the depth of the reinforced earth wall from surface, and increased with the lapse of time after construction. 4.The failure surface of the reinforced earth wall by the concrete skin was about 60$^{\circ}$and the failure behavior of the reinforced earth wall in which the fabric filter was buried was slow, and so the pore pressure could be decreased. 5.It is possible to construct the fabric retained earth wall by the plastic fabric filter only. And the reinforcing effect between the steel plate and the plastic fabric filter is not largely different. however, in the aspect of the economic durability, the plastic fabric filter is more advantageous. 6.The reinforcing action mainly depends on the width and the length of the reinforcing materials, if possible, the full width is advantageous to enlarge the contact area with backfill. but considering the economic aspect, it is neccessary to develop the method controlling the space of the strip.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2004.10a
• /
• pp.211-214
• /
• 2004

In the present study, the effect of SIDT (Strain Induced Dynamic Transformation) on the microstructure of medium carbon steels was investigated to develop spheroidized annealing-free steel wire rods. When $0.45\%C$ steels were hot-deformed under the conditions of heavy reduction at low temperatures, a microstructure quite different from conventional ferrite-pearlite structure was obtained. It was considered that this ferrite-cementite microstructure was obtained because very small retained austenite grains existing between fine SIDT ferrites prefer to transform to cementite and ferrite instead of pearlite during cooling. Through the present study, $0.45\%C$ steels containing ferrite-cementite (FC) structure instead of ferrite-pearlite structure was obtained in as-rolled state by introducing SIDT. The specimen containing the FC structure was much softer than that containing conventional ferrite-pearlite structure. Therefore, it is concluded that deforming medium carbon steels under the conditions of SIDT is a very powerful method to obtain soft steel wire rods which could be cold-forged without softening heat-treatment

• Journal of Microbiology and Biotechnology
• /
• v.23 no.1
• /
• pp.56-63
• /
• 2013

We have characterized the putative ${\alpha}$-glucosidase gene (st2525) selected by total genome analysis from the acidothermophilic crenarchaeon Sulfolobus tokodaii strain 7. The ORF was cloned and expressed as a fusion protein in Escherichia coli, and recombinant ST2525 was purified by Ni-NTA affinity chromatography. Maximum activity was observed at $95^{\circ}C$ and pH 4.0, and the enzyme exhibited stability with half-lives of 40.1 min and 7.75 min at extremely high temperatures of $100^{\circ}C$ and $105^{\circ}C$, respectively. The enzyme retained at least 85% of its maximal activity in the pH range of 4.0-11.0. ST2525 exclusively hydrolyzed ${\alpha}$-1,4-glycosidic linkages of oligosaccharides in an exo-type manner, with highest catalytic efficiency toward maltotriose. The enzyme also displayed transglycosylation activity, converting maltose to isomaltose, panose, maltotriose, isomaltotriose, etc. From these results, ST2525 could be potentially useful for starch hydrolysis as well as novel synthesis of oligosaccharides in industry.