• 콘크리트학회지
• /
• 제8권5호
• /
• pp.111-122
• /
• 1996

본 연구에서는 매스콘크리트의 외부구속도의 특성을 검토하기 위하여, 타설높이를 1.0m로 고정시킨 상태에서 타설블럭의 밑면길이와 타설높이와의 비(L/H), 하부 구속체의 탄성계수($E_r$) 등 매스콘크리트 구조물에서 특히 외부구속에 영향을 미치는 인자를 대상으로 parameter study를 실시하여 각 인자가 온도응력에 미치는 영향을 검토하고 각 인자간의 상호 영향도에 대해서도 검토하였다. 검토결과, 외부구속에 의해 발생하는 응력은 단면 높이방향으로 거의 직선분포를 이루고 있으며, L/H나 구속체 탄성계수의 크기에 따라서도 다르고 타설한 콘크리트의 강도발현에 따른 탄성계수의 증가 및 체적변화로 이해서 재령별로도 그 영향이 각각 다르다는 것을 알았다. 또한, 외부구속은 축방향구속과 휨방향구속으로 나누어 평가할 수 있으며, 외부구속이 약한 경우는 휨방향구속이 탁월하고, 외부구속이 강한 경우는 축방향구속이 탁월하다는 것을 알았다. 그리고타설높이 H를 1.0cm로 제한 시킨 경우에 ACI 207 위원회법으로 계산한 결과를 본 해석결과와 비교한 결과, ACI위원회법으 외부고속이 약한 경우에는 본 해석결과보다 큰 값으로 평가하고, 외부구속이 강한 경우에는 작게 평가하고 있음을 알았다.

• 대한기계학회논문집A
• /
• 제30권9호
• /
• pp.1134-1141
• /
• 2006

This paper presents the model for evaluating restraint effect of pressure induced bending (PIB) on the circumferential through-wall crack opening displacement (COD), which considers plastic behavior of crack. This study performed three-dimensional elastic-plastic finite element (FE) analyses for different crack angle, restraint length, pipe geometry, stress level, and material conditions, and evaluated the influence of each parameter on the PIB restraint effect on COD. Based on these evaluations and additional perfectly-plastic FE analyses, a closed-form model to evaluate the restraint effect of PIB on the plastic crack opening of circumferential through-wall crack, was proposed as functions of crack angle, restraint length, radius to thickness ratio, axial stress corresponding to an internal pressure, and normalized COD evaluated from linear-elastic crack opening condition.

• Archives of Pharmacal Research
• /
• 제16권1호
• /
• pp.71-74
• /
• 1993

The protective effect of adenosine triphosphate (ATP) on gastic ulcer induced in rats has been studied. Gastic ulceration was induced by hypothemic restraint stress or dicolofenac sodium. Gastic acid secretion and mucosal injury produced by the hypothemic restraint stress was greater as compared with those produced by diclofenac sodifum. ATP significantly reduced area of injury, however, increased cyclic adenosine monophosphate (cATP) content. Administration of dipyridamole along with ATP did not change the total lesion area in both models when compared to ATP alone. Aminophyline antagonized antagonized the protective effect of ATP on the injured area. Famotidine was found to be effective in reducing gastric acid output as well as the total injured area without any change in cAMP content when given along with ATP.

• 대한기계학회논문집A
• /
• 제25권11호
• /
• pp.1873-1880
• /
• 2001

The effects of restraint of pressure induced bending(PIB) on crack opening for circumferential through-wall crack in a pipe were investigated. In this study, the elastic and elastic-plastic finite element analyses were performed to evaluate crack opening displacement(COD) for various restraint conditions and crack size. The results showed the restraint of PIB decreased crack opening for a given crack size and tensile stress, and the decrease in crack opening was considerable for large crack and short restraint length. A1so, the effect was more significant in tole results of elastic-plastic analysis compared with in the elastic analysis results. In the elastic-plastic analysis results, tole restraint effect was increased with increasing applied tensile stress corresponding to internal pressure. Additionally, the restraint effect on COD was independent on the variation in pipe diameter and decreased with increasing pipe thickness, and It depended on not total restraint length but shorter restraint length for non-symmetrically restrained.

• Laboraroty Animal Research
• /
• 제34권4호
• /
• pp.203-210
• /
• 2018

Stress severely disturbs physiological and mental homeostasis which includes adult neurogenesis in hippocampus. Neurogenesis in hippocampus is a key feature to adapt to environmental changes and highly regulated by multiple cellular signaling pathways. The primary cilium is a cellular organelle, which acts as a signaling center during development and neurogenesis in adult mice. However, it is not clear how the primary cilia are involved in the process of restraint (RST) stress response. Using a mouse model, we examined the role of primary cilia in repeated and acute RST stress response. Interestingly, RST stress increased the number of ciliated cells in the adult hippocampal dentate gyrus (DG). In our RST model, cell proliferation in the DG also increased in a time-dependent manner. Moreover, the analysis of ciliated cells in the hippocampal DG with cell type markers indicated that cells that were ciliated in response to acute RST stress are neurons. Taken together, these findings suggest that RST stress response is closely associated with an increase in the number of ciliated neurons and leads to an increase in cell proliferation.

• Journal of Welding and Joining
• /
• 제19권5호
• /
• pp.548-554
• /
• 2001

The restraint force is required an accurate measurement and analysis to protect weldment from residual stress. Also, this residual stress caused by clacks in weldments are often observed in the weldments of large size nozzles or radial tanks after welding. This paper is preformed on the study of evaluation of welding restraint forces using load cell with STS thin plate which are using pressure vessel steel in the industry field. As a result of this study, as the welding currents are higher and the welding speeds are more slowly, the magnitude of restraint force in process of the flat plate welding hows to be more large. Also, the temperature in process of melting is increasingly rising, then the restraint forces exhibit the compressive forces, whereas the restraint forces during cooling represent extensional force.

• Advances in concrete construction
• /
• 제14권2호
• /
• pp.139-151
• /
• 2022

Filling materials poured into precast member joint are subjected to restraint stress by the precast member and joint reinforcement. The induced stress will likely cause cracks at early ages and performance degradation of the entire structure. To prevent these issues and design reasonable joints, it is very important to analyze and evaluate the restrained shrinkage cracks of filling materials at various restraint conditions. In this study, a new time zero-that defines the shrinkage development time of a filling material-is proposed to calculate the accurate amount of shrinkage. The tensile stresses and strengths at different ages were compared through the ring test (AASHTO PP34) to evaluate the crack potential of the restrained filling materials at various restraint conditions. The mixture which contained an expansive additive and a shrinkage reducing agent exhibited high resistance to shrinkage cracking owing to the high-drying shrinkage compensation effect. The high-performance, fiber-reinforced cement composite, and ultra-high-performance, fiber-reinforced cement composite yielded very high resistance to shrinkage and cracking owing to the pull-out property of steel fibers. To this end, multiple nonlinear regression analyses were conducted based on the test results. Accordingly, a modified tensile stress equation that considered both the geometric shape of the specimen and the intrinsic properties of the material is proposed.

• International Journal of Concrete Structures and Materials
• /
• 제6권4호
• /
• pp.221-230
• /
• 2012

Cracking of repair material due to restraint of shrinkage could hinder the intended extension of serviceability of repaired concrete structure. The availability of model to predict shrinkage stress under restraint condition will be useful to assess whether repair material with particular deformation properties is resistance to cracking or not. The accuracy in the prediction will depend upon reliability of the model, input parameters, testing methods used to characterize the input parameters, etc. This paper reviews a variety of models to predict shrinkage stress in patch repair system. Effect of creep and composite action to release shrinkage stress in the patch repair system are quantified and discussed. Accuracy of the models is examined by comparing predicted and measured shrinkage stress. Simplified model to estimate shrinkage stress is proposed which requires only shrinkage property of repair material as an input parameter.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2009년 추계학술발표대회
• /
• pp.102-102
• /
• 2009

The purpose of this study is to establish the predictive equation of transversal residual stress at the thick weldment of large container ship. In order to do it, the variables used for this study were restraint degree, yield strength of base material, thickness of weldment and welding heat input. Here, the level of restraint degree at the thick weldment of container ship having the various welding sequence was calculated using FEA. From the result, the h-type specimen was designed to simulate the level of restraint degree at the actual weldment of containership. With H-type test specimen designed, the effect of the variables on the distribution of transversal residual stress at the weldment in a container ship was evaluated using the comprehensive FEA. Based on the results, the predictive equations of mean value and the distribution of transverse residual stress in each location of residual stress were established using dimensional analysis and multiple-regression method. The validation of predictive equations was verified by comparing with measured results by XRD in the actual weldment of the ship.

• Journal of Welding and Joining
• /
• 제8권3호
• /
• pp.79-88
• /
• 1990

Welded joint often contains soft or softened regions such as the HAZ of TMCP steel welded with high heat input. In this study, the equivalent yield strength of plate structure containing softened region was predicted by FEM analysis, and its incremental behavior was explained with the results of the analysis. The calculated results of yield strength indicated the following for the plate structures. 1) As the softened region starts to yield, shear stress begins to build up along the boundary between base metal and softened region. This results in multi-axial stress condition which gives restraint on the softened region. 2) Restraint effect has a significant influence on the distribution of the shear stress, the nominal stress, and the strain. 3) The yielding behavior of softened region becomes the same as that of base metal when both ratios of length to width and thickness to width of softened region are larger than 30 and 13 respectively.