• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.21 no.11
• /
• pp.1527-1537
• /
• 1997

Extinction characteristics and acoustic response of hydrogen-air diffusion flames at various pressures are numerically studied by employing counterflow diffusion flame as a model flamelet in turbulent flames in combustion chambers. The numerical results show that extinction strain rate increases linearly with pressure and then decreases, and increases again at high pressures. Thus, flames are classified into three pressure regimes. Such nonmonotonic behavior is caused by the change in chemical kinetic behavior as pressure rises. The investigation of acoustic-pressure response in each regime, for better understanding of combustion instability, shows different characteristics depending on pressure. At low pressures, pressure-rise causes the increase in flame temperature and chain branching/recombination reaction rates, resulting in increased heat release. Therefore, amplification in pressure oscillation is predicted. Similar phenomena are predicted at high pressures. At moderate pressures, weak amplification is predicted since flame temperature and chain branching reaction rate decreases as pressure rises. This acoustic response can be predicted properly only with detailed chemistry or proper reduced chemistry.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2009.10a
• /
• pp.1164-1167
• /
• 2009

Motion-image-quality of LCD-TVs is discussed by dynamic spatial frequency response. Smaller temporal aperture or higher frame rate can improve dynamic response, but an increase of motion velocity easily cancels the improvement. A guideline for deciding the desirable temporal aperture and frame rate of LCD-TVs is described, under the condition that camera and display have the same parameters. Two candidates of the desirable parameter sets will be (240 or 300 Hz, 50 to 100% aperture) and (120Hz, 25 to 50% aperture), from the viewpoint of "limit of acceptance" on motion-imagequality-deterioration for critical picture materials.

• YAKHAK HOEJI
• /
• v.39 no.5
• /
• pp.480-486
• /
• 1995

The change in discharge current of a glow discharge has been shown the potential sensitive detector for gas chromatography. To investigate the effect of carrier gas on the electrical characteristics of the discharge and the peak response, the discharge pressure, gas flow rate, and discharge gap have been studied. The discharge gas included the Ar, He, and N$_{2}$. The gas flow rate has been found one of the important parameters to affect both the electrical characteristics and the peak response.

• Bulletin of the Korean Space Science Society
• /
• 2009.10a
• /
• pp.36.3-37
• /
• 2009

This is an attempt to improve a formula to predict variations of geomagnetic storm indices (Dst) from solar wind parameters. A formula which is most widely accepted was given by Burton et al. (1975) over 30 years ago. Their formula is: dDst*/dt = Q(t) - Dst*(t)/$\tau$, where Q(t) is the Dst injection rate given by the convolution of dawn-to-dusk electric field generated by southward solar wind magnetic field and some response function. However, they did not clearly specify the response function. As a result, misunderstanding seems to be prevailing that the injection rate is proportional to the dawn-to-dusk electric field. In this study we tried to determine the response function by examining 12 intense geomagnetic storms with minimum Dst < -200 nT for which solar wind data are available. The method is as follows. First we assume the form of response function that is specified by several time constants, so that we can calculate the injection rate Q1(t) from the solar wind data. On the other hand, Burton et al. expression provide the observed injection rate Q2(t) = dDst*/dt + Dst*(t)/$\tau$. Thus, it is possible to determine the time constants of response function by a least-squares method to minimize the difference between Q1(t) and Q2(t). We have found this simple method successful enough to reproduce the observed Dst variations from the corresponding solar wind data. The present result provides a scheme to predict the development of Dst 30 minutes to 1 hour in advance by using the real time solar wind data from the ACE spacecraft.

• Proceedings of the KSME Conference
• /
• 2007.05b
• /
• pp.2885-2889
• /
• 2007

In this study, the effect of particle aggregation on dynamic response time of Electrorheological (ER) fluid is investigated. The particle aggregation time is defined as the time interval between the application of the field and the formation of the first chain bridging the two electrodes. The dynamic response times of an ER fluid sheared between two concentric cylinders have been obtained under two different experimental conditions: the one is that the electric field is induced before shearing, and the other is that the electric field is induced after shearing. From the difference between two response times, the particle aggregation times are determined under various electric fields and shear rates. The experimental results show that the aggregation rate is decreased with an increase of shear rate, while electric field has little effect on it. Therefore, it is verified that the hydrodynamic force hinders the formation of chain-like structures.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.33 no.6
• /
• pp.411-417
• /
• 2009

The transient shear stress response of an electrorheological fluid is investigated experimentally. The characteristic time constants of an electrorheological fluid sheared between two concentric cylinders were obtained under various electric field strengths and shear rates. Also, two experimental modes are adopted to investigate the effect of the shear flow on the dynamic behavior of the fluid; one is that the electric field is induced before shearing, and the other is the electric field is induced after shearing. From the difference in the response time between two modes, the cluster formation time were obtained. The response times were decreased with the increase of the shear rate, irrelatively of the electric field strength. The cluster formation time were monotonically increased with increase of shear rate, and thereafter, were converged with a certain value.

• Computational Structural Engineering
• /
• v.9 no.4
• /
• pp.107-115
• /
• 1996

Displacement response is one of the important parameter to determine vibration characteristics of bridge structure. Reliable estimate of displacement response is obtained economically from integration of measured acceleration data in frequency domain. Proper sampling rate of frequency in discretization process of measured acceleration is proposed. Comparison of integrated and directly measured displacement response from laboratory experiment for a cantilever beam shows good agreement each other. Mode shape obtained from estimated displacement response also closely match with analytical result, thus the developed method is proved to be effective in practical use.

• Journal of the Korean Society for Precision Engineering
• /
• v.14 no.9
• /
• pp.124-129
• /
• 1997

The purpose of this study is to predict the stability and frequency response of multipurpose vehicle. The vehicle model has seven degrees of freedom. The motion equations are derived by using Lagrangian equation and linearized. The positions of eigenvalues of model which are dominated by lateral velocity, yaw rate, roll rate of sprung mass are used to predict the stability of motion. The resonse of sprung mass to steering wheel is simulated in time domain. It is predicted that the roll response of sprung mass would rather be improved by modifying the position of eigenvalues. The responses of sprung mass to steering wheel are also simulated in frequency domain. The magnitude and phase plots of gains are evaluated in driver's steering input frequency range.

• International conference on construction engineering and project management
• /
• 2020.12a
• /
• pp.257-264
• /
• 2020

Objective: To investigate test-retest reliability and responsiveness of Equivital Lifemonitor and photoplethysmography based wristwatch tools in assessing physiological parameters during a simulated fatigue task. Methods: Ten university students (Mean age, 30.6 ± 1.7 years) participated in this pilot study. Participants were asked to perform a 30-minute of a simulated fatigue task in an experimental setup in a lab. The physiological parameters (e.g., heart rate, heart rate variability, respiratory rate, electrodermal activity, and skin temperature) were measured at baseline and immediately after the fatigue task. An intraclass correlation coefficient (ICC2,1) was used to evaluate the test-retest reliability of each tool in assessing physiological measures. In addition, the responsiveness of each tool to measure changes from baseline to posttest was calculated using a standardized response mean. Results: The Equivital Lifemonitor has shown good to excellent test-retest reliability for the assessment of heart rate (ICC, 0.97), heart rate variability (ICC, 0.86), respiratory rate (ICC, 0.77), and local skin temperature (ICC, 0.76). However, photoplethysmography based wristwatch showed moderate to good test-retest reliability for the assessment of heart rate (ICC, 0.71), heart rate variability (ICC, 0.73), electrodermal activity (ICC, 0.80), and skin temperature (ICC, 0.72). A large standardized response mean (>0.8) indicates that both tools can capture the changes in heart rate, heart rate variability, respiratory rate, skin temperature, and electrodermal activity after a 30-minute of fatigue task. Conclusions: The Equivital Lifemonitor and photoplethysmography based wristwatch devices are reliable in measuring physiological parameters after the fatigue task. Additionally, both devices can capture the fatigue response after a simulated construction task. Future field studies with a larger sample should investigate the sensitivity and validity of these tools in measuring physiological parameters for fatigue assessment at construction sites.

• Korean Journal of Animal Reproduction
• /
• v.26 no.1
• /
• pp.69-72
• /
• 2002

Two trials were conducted in a commercial dairy on heifer synchronization with PGF$_2$$\alpha$. Animals showing estrous following the first injection were bred and animals not showing estrus were given the second injection 10 days later. In the first trial, the injection routes were rump and rump. In the second trial, the injection routes were rump and shoulder. Estrous detection were performed from 24 h after injection. Animals were bred by the same technician. In the first trial, the response rate for the first injection was 51.4% and the subsequent pregnancy rate of these animals was 60.0%. The response rate in the second injection was 57.1% and the pregnancy rate was 50.0%. In the second trial, the response rate in the first injection on the rump was 48.7% and the subsequent pregnancy rate was 70.6%. The second injection was given on the shoulder and the response rate was 60.0% and the subsequent pregnancy rate was 25.0%. The data suggest that the route of PGF$_2$$\alpha$ administration was critical to achieve success in estrous synchronization and pregnancy rates.