• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.48 no.7
• /
• pp.376-383
• /
• 1999

The piezoelectric transformer (PT) is an electro-mechanical device that transfers electrical energy through a mechanical vibration. In this paper, a PT operating in the contour vibration mode is introduced for an application of fluorescent lamp ballast. Utilizing its inherent characteristics of the LC resonator and a high voltage gain to ignite the lamp in light load condition, an investigation of a power piezoelectric transformer as a potential component for a fluorescent lamp ballast is discussed. PT is easy to be produced in mass and reduces the cost of the ballast. The modified equivalent circuit model of the PT considering the operating current level is derived to design the fluorescent lamp ballast. This model describes the voltage gain of the PT in wide load variations and various input current levels. The experimental and simulation results are provided to verify theoretical analysis. The power capacity of the currently developed PT is relatively low (15W), but it can be increased by adopting a multi-layer structure and is currently under investigation. It is also possible to parallel the PT for higher power processing.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.35 no.3
• /
• pp.312-322
• /
• 1999

A ultrasonic transduce with a single acoustic matching layer has been designed as an attempt to increase the bandwidth of underwater transducer. The wideband resonance condition was accomplished by attaching a single matching layer on the front face of a ceramic resonator composed of a piezoelectric bar, a taper part and a head part. A modified Mason's model was used for the performance analysis and the design of transducers, and the constructed transducers were tested experimentally and numerically by changing the impedance and thickness of the matching layer in the water tank.The obtained results are summarized as follows:1. Measured resonant and antiresonant frequencies of the piezoelectric transducer with no matching layer in air were 24.7 kHz and 25.6 kHz, respectively. 2. Two resonant frequencies of the piezoelectric transducer with a single matching layer were 21.7 kHx and 26.9 kHz, respectively, in air and 21.4 kHz and 22.7 kHz, respectively, with a water load.3. Two distinct resonance peaks in the transmitting voltage response(TVR) of the developed transducer were observed at 22.0 kHz and 25.8 kHz, respectively, with center frequency of 24.0 kHz. The values of TVR at these frequencies were 130.1 dB re $1 \muPa$/V at 22.0 kHz and 128.5 dB re $1 \muPa$/V at 25.8 kHz, respectively.Reasonable agreement between the experimental results and the numerical values was achieved.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.14 no.1
• /
• pp.20-26
• /
• 2003

This paper presents hairpin-comb bandpass filter using ground aperture. Hairpin-comb resonator maintains the weak coupling though the space between two resonators is very small. This has the good merit that the entire filter size is small for narrowband bandpass filter. The coupling between two hairpin-comb resonators so very weak that can't be applicable to general microstrip. We compensate the coupling by using ground aperture. It makes the hairpin-comb filter possible that can be applicable to general microstrip. Also it has the good merit which adjusts the bandwidth by changing the size of aperture without changing the space. In this paper, we fabricate the bandpass filter, which has 1.78 GHz center frequency and 62 MHz (3.5%) fractional bandwidth.

• Proceedings of the Korea Electromagnetic Engineering Society Conference
• /
• 2005.11a
• /
• pp.7-12
• /
• 2005

A compact microstrip band-selective filter for ultra-wideband (UWB) radio system is proposed. The filter combines the traditional short-circuited stub highpass filter and coupled resonator bandstop filter on both sides of the mitered 50-ohm microstrip line. To realize the pseudo-highpass filtering characteristic over UWB frequency band (3.1 GHz to 10.6 GHz), a distributed highpass filter scheme is adopted. Three coupled resonators are utilized to obtain the band stop function at the desired frequency band. By meandering the coupled resonators, there is 29% reduction in footprint compared to the traditional bandstop filter using L-shaped resonators. The measured results show that the filter has a wide passband of 146.7 % (2.1 GHz to 10.15 GHz) with low insertion loss and the stop band of 7.42 % (5.32 GHz to 5.73 GHz) for 3-dB bandwidth. The measured group delay is less than 0.7 ns within the passband except the rejection band.

• ETRI Journal
• /
• v.30 no.2
• /
• pp.268-274
• /
• 2008

This paper proposes an open-loop clock recovery circuit (CRC) using two high-Q dielectric resonator (DR) filters for 39.8 Gb/s and 42.8 Gb/s dual-mode operation. The DR filters are fabricated to obtain high Q-values of approximately 950 at the 40 GHz band and to suppress spurious resonant modes up to 45 GHz. The CRC is implemented in a compact module by integrating the DR filters with other circuits in the CRC. The peak-to-peak and RMS jitter values of the clock signals recovered from 39.8 Gb/s and 42.8 Gb/s pseudo-random binary sequence (PRBS) data with a word length of $2^{31}-1$ are less than 2.0 ps and 0.3 ps, respectively. The peak-to-peak amplitudes of the recovered clocks are quite stable and within the range of 2.5 V to 2.7 V, even when the input data signals vary from 150 mV to 500 mV. Error-free operation of the 40 Gb/s-class optical receiver with the dual-mode CRC is confirmed at both 39.8 Gb/s and 42.8 Gb/s data rates.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.21 no.1
• /
• pp.18-23
• /
• 2011

With hydraulic noise test facility, a variety of tests were performed to investigate the pulsation pressure generation mechanism and its transmission characteristics and to derive the noise control methodology. Many experiments were carried out by changing average pressure, flow rate, pump speed, hose length and MCV spool condition. From the test results, the correlations between pulsation pressure and other design parameters, such as static pressure, flow rate and MCV spool opening area and length of hose, were found out. And also each contribution factors were evaluated from the regression analysis. By changing hose length, the pulsation pressure resonance phenomenon was investigated. In order to find out the pulsation pressure reduction measures pulsation pressure analysis, such as pulsation pressure of hydraulic pump itself and pulsation pressure of hydraulic system, by using AMESim were studied. In addition hydraulic silencer was developed based on the Helmholtz resonator. And its performance was evaluated by installing the silencer at the excavator.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.4 no.3
• /
• pp.557-564
• /
• 2000

A microstrip band-pass filter using cross-coupled resonators is designed and studied experimentally. The cross-coupled microstrip hairpin resonator filters exhibit ripples in both passband and stopband. These ripples can improve both frequency selectivity and insertion loss. The cross-coupled filters are not only simple and compact in configuration, but also have great flexibility to form filters into a variety of size. In this paper, a microstrip band-pass filter using cross-coupled resonators is designed at the center frequency of 1.8GHz with bandwidth of 5.0% using Ensemble software. The experimental results show that the bandwidth is about 4.53% at 1.8GHz.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.21 no.1
• /
• pp.83-89
• /
• 2010

In this paper, we propose a new varactor coupled line structure and design the VCO using the proposed structure. The proposed coupled line structure removes the reflected signals from the varactor diode using an added $\lambda$/4 transmission line. The frequency synthesizers are designed using the PLL technique at Ku-band. The synthesizer using the proposed coupled structure has 38 MHz frequency tuning range and -97 dBc/Hz phase noise characteristic at 100 KHz offset frequency. The measured results show improved tuning range as well as the improved phase noise characteristics compared to the conventional designs.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.5 no.1
• /
• pp.26-32
• /
• 2012

This paper presents a metamaterial absorber unit sell structure with four-element electric-LC resonators (ELC). In order to enhance the operating bandwidth of the proposed absorber unit cell two pairs of ELC resonators with a different size are used. The proposed unit cell shows negative permittivity and permeability when the electric field is parallel to the capacitive gap and the magnetic field is normal to the plane of ELC resonator. The simulated results show peak absorbance over 90% at two frequencies of 8.53 and 9.08 GHz, respectively.

• Journal of Electrical Engineering and Technology
• /
• v.12 no.4
• /
• pp.1556-1565
• /
• 2017

This paper depicts the design, implementation and analysis of efficient resonant based wireless power transfer (WPT) technique using three magnetic coupled coils. This work is suitable for mid ranged device due to small form factor while minimizing the loading effect. A multi turned loop size resonator is exploited for both the transmitter and receiver for longer distance. In this paper, class-E power amplifier (class-E PA) is introduced with an optimum power tracking mechanism of WPT system to enhance the power capability at mid-range with a flat gain. A robust method of finding optimum distance is derived with an experimental analysis of the designed system. In this method, the load sensitive issue of WPT is resolved by tuning coupling coefficient at considerable distances. Our designed PA with a drain efficiency of 77.8% for a maximum output of 5W is used with adopted tuning technique that improves the overall WPT system performance by 3 dB at various operating points.