• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.29 no.2A
• /
• pp.195-201
• /
• 2004

In this paper, U-Shaped slot Bow-Tie antenna for 5.15㎓∼5.35㎓ is designed, fabricated, and measured. The prototype consist of U-Shaped slot. To obtain suitable bandwidth, the form layer is inserted between ground plane and substrate. Important parameters in the design are U-slot length, width, position, air-gap height, and feed point position. From these parameters optimized, a U-shaped slot Bow-Tie antenna is fabricated and measured. The measured results of the antenna are obtained as follows results. The resonant frequency of the Fabrication U-shaped slot Bow-Tie antenna is 5.28㎓, bandwidth for approximately 7.76％(VSWR<1.2) and the gain is 4∼7dBi. The experimental far-field patterns are stable across the pass band. The 3dB bandwidth in Elevation and Azimuth are 73.63$^{\circ}$and 65.08$^{\circ}$, respectively.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.29 no.3A
• /
• pp.303-310
• /
• 2004

In this paper, L-shaped slot antenna for 5.15㎓-5.35㎓ is designed, fabricated. and measured. The prototype consist of four L-shaped slot. To obtain suitable bandwidth, the form layer is inserted between ground plane and substrate. Important parameters in the design are four L-slot length. width, position, air-gap height. and feed Point position. From these parameters optimized, a four L-shaped slot antenna is fabricated and measured. The measured results of the antenna are obtained as follows results. The resonant frequency of the fabrication four L-shaped slot antenna is 5.25㎓, bandwidth for approximately 5％(VSWR＜1.5) and the gain is 8-9㏈i. The experimental far-field patterns are stable across the pass band. The 3dB bandwidth in H-Plane and I-Plane are 69$^{\circ}$and 62$^{\circ}$, respectively.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.28 no.6A
• /
• pp.414-424
• /
• 2003

In this paper, a multiple U-shaped slot antenna for 5.25㎓~5.35㎓ is designed, fabricated, and measured. The prototype consists of U-slot and two invert U-slot. To obtain enough bandwidth, the foam layer is inserted between ground plane and substrate. Important parameters in the design are U-slot length, width, position, airgap length, and feed point. From these parameters optimized, a multiple U-shaped slot antenna is fabricated and measured. The measured results of the antenna are compared with its simulated results. The resonant frequency of the fabricated multiple U-shaped slot antenna is 5.25㎓ the bandwidth for approximately 7.4%(VSWR<1.5) and the gain is 2.9~5.3dBi. The experimental far-field patterns are stable across the pass band. The 3dB bandwidth in H-Plane and I-Plane are 62$^{\circ}$ and 50$^{\circ}$, respectively.

• Journal of electromagnetic engineering and science
• /
• v.18 no.2
• /
• pp.117-128
• /
• 2018

In this paper, compact linear dual polarized series-fed $1{\times}2$ linear and $2{\times}2$ planar arrays antennas for airborne SAR applications are proposed. The proposed antenna design consists of a square radiating patch that is placed on top of the substrate, a quarter wave transformer and $50-{\Omega}$ matched transformer. Matching between a radiating patch and the $50-{\Omega}$ microstrip line is accomplished through a direct coupled-feed technique with the help of an impedance inverter (${\lambda}/4$ impedance transformer) placed at both horizontal and vertical planes, in the case of the $2{\times}2$ planar array. The overall size for the prototype-1 and prototype-2 fabricated antennas are $1.9305{\times}0.9652{\times}0.05106{{\lambda}_0}^3$ and $1.9305{\times}1.9305{\times}0.05106{{\lambda}_0}^3$, respectively. The fabricated structure has been tested, and the experimental results are similar to the simulated ones. The CST MWS simulated and vector network analyzer measured reflection coefficient ($S_{11}$) results were compared, and they indicate that the proposed antenna prototype-1 yields the impedance bandwidth >140 MHz (9.56-9.72 GHz) defined by $S_{11}$<-10 dB with 1.43%, and $S_{21}$<-25 dB in the case of prototype-2 (9.58-9.74 GHz, $S_{11}$< -10 dB) >140 MHz for all the individual ports. The surface currents and the E- and H-field distributions were studied for a better understanding of the polarization mechanism. The measured results of the proposed dual polarized antenna were in accordance with the simulated analysis and showed good performance of the S-parameters and radiation patterns (co-pol and cross-pol), gain, efficiency, front-to-back ratio, half-power beam width) at the resonant frequency. With these features and its compact size, the proposed antenna will be suitable for X-band airborne synthetic aperture radar applications.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.20 no.6
• /
• pp.535-543
• /
• 2009

This paper describes a design for RFID(Radio Frequency Identification) tag antenna using license plate attached the vehicle bumper in 900 MHz band. The proposed tag antenna size which is located on upper center position of a vehicle license plate is 162.5${\times}$40${\times}$1 mm$^3$. A resonant frequency of design antenna and the bandwidth which has return loss of -10 dB below are 900 MHz and about 720 MHz(640${\sim}$1,360 MHz), respectively. The commercial chip impedance considered on design was 16- j131 ${\Omega}$ and the complex conjugate impedance of chip was used as input impedance of tag antenna. The measured return loss and radiation pattern were agreed well with the calculated results. The measured readable range of the proposed tag antenna designed on only the vehicle license plate was 11.5 m. Moreover, its range of the fabricated tag antenna that the license plate and the vehicle bumper were fixed by volt and nut was observed 10.4 m. These measured readable range showed about 5 m above far distance more than the average readable range of commercial tag antenna.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.18 no.3 s.118
• /
• pp.273-281
• /
• 2007

This paper presented design for a dipole antenna operated at 900 MHz band RFID tag, and antenna performance varied by the sticked material was experimentally evaluated. When dipole antenna was sticked by the material having a difffrent electric characteristic such as dielectric material, fero-magnetic material and conductor, variations of antenna return loss and radiation pattern according to the sticked material kinds, size, and height between antenna and the sticked plate were experimentally observed and evaluated. When antenna was sticked by dielectric surface, the measured return loss and radiation pattern by affection of different dielectric permittivity ratio showed resonant frequency shift of about 40 MHz and relative attenuation of 1 dB to 3 dB. Even though frequency shift by size variation of the sticked plate was observed, the measured radiation pattern of dipole antenna located on the sticked plate was similar with one without backside plate. In the case of conductor or fero-magnetic material as the sticked ground plate, because of frequency shift and phase difference by distance between dipole antenna and the sticked ground plate, amplitude decrease of radiation pattern at 910 MHz was observed about 5 dB above.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.14 no.2
• /
• pp.121-136
• /
• 1989

In this paper, an attempt has been made to analyze the theoretically and verify experimentally the effect of curvature on the radiation characteristics of microstrip array antennas mounted conformally on the concave surface and the convex surface of the cylindrical body. The analysis of single element microstrip antenna is made by using the analysis method of Transmission Line Model. The theory of array antennas is established by application of the method of transformed coordinates, in which the translation and the ratation about each single element arrayed two-demensionally on the nonplanar surface are under consideration, and it is investigated by computation of the synthetic electric field strength in the far zone. In addition, various radiation characteristics, such as return loss, resonant frequency, radiation pattern, half-power, beamwidth, gain, are measrued and compared with the theroetical values according to the variation of curvature, by designing and building 4-element array microstrip antenna operating at 10 GHz, and microstrip feed lines. As predicted in theroy, it is verified that radiation pattern of antennas mounted on the concave and the convex surfaces alike broadens as the radius of curvature decreases. And for the curved surfaces, aggrement between computed values of the total synthetic radiation power pattern by the method of transformed coordinates and measured valuse is good. Besides, it is found that resonant frequency, input impedance and gain are hardly affected by the radius of curvature.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.16 no.5 s.96
• /
• pp.526-533
• /
• 2005

In this paper, the miniaturized the linear polarization and the circular polarization microstrip antennas, which are the two ends in the resonance length direction or all the four-ends were folded are designed and fabricated at the resonant frequency of 1.575 GHz(fur GPS system). For the linear polarization microstrip antenna, the antenna was bent. downward so that the visible length(=L) was reduced by $31.7\%(\varepsilon_r=1.06)$. The folded antenna was folded toward the center of the antenna once again. In this case, the visible length reduction rate, gain, -10 dB bandwidth, E-plane and H-plane HPBW were $73.9\%$, 5.12 dBd, $64MHz(4\%),\;151^{\circ}\;and\;79.2^{\circ}$, respectively. For the circular polarization microstrip antenna, the folded structure of the linear polarization antenna was applied to all the few directions. For the most efficiency the folded bottom surfaces were designed in a triangular shape. In this case, the visible area reduction rate, gain, -10 dB bandwidth, and HPBW in horizontal polarization of the z-x plane and the z-y plane were $71.5\%,\;3.96dBd,\;84MHz(5.3\%),\;80.6^{\circ}\;and\;82.1^{\circ}$, respectively. Therefore, we have confirmed that the folded structure is suitable fer the miniaturization of the microstrip antenna.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.21 no.8
• /
• pp.886-892
• /
• 2010

In this paper, the hybrid antenna utilizing epsilon negative zeroth-order resonance(ENG ZOR) and $TM_{010}$-mode is presented. The antenna has a directional radiation pattern and improved bandwidth. To obtain a ENG ZOR and $TM_{010}$-mode, the hybrid antenna employs the mushroom structure and the microstrip patch, respectively. Two antennas of the mushroom and the patch are coupled by gap and fed by one coaxial feed. The frequencies of ENG ZOR and of $TM_{010}$ resonance are designed to be 4 GHz and 3.9 GHz, respectively. Because two resonant frequencies are set to be close, the dual-resonance can be formed, resulting in the broader bandwidth. Even though the radiation pattern of an ENG ZOR antenna is omnidirectional, the directional radiation of a microstrip patch antenna compensates the null of omnidirectional pattern of an ENG ZOR antenna. Thus, the hybrid antenna has a directional radiation pattern. The antennas having 4, 3, and 2 unit cells of mushroom structure are designed and analyzed. The antennas have fractional bandwidths of 4.29~4.95 %, gains of 3.16~5.57 dBi, and radiation efficiencies of 62.4~94.2 %.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.10 no.2
• /
• pp.374-379
• /
• 2006

In this paper, the high Gain and the wideband microstrip patch antenna, which is applicable to 5 GHz band wireless LAN, is designed and fabricated. Firstly to widen the bandwidth of microstrip antenna, U-Slot in rectangular form patch is inserted and used the microstrip line-Coaxial probe feeding method. Secondly, the antenna gain is improved to be embodied in $2{\times}2$ array form. As a result, in this paper, is designed and fabricated 5 GHz Band wideband U-Slot $2{\times}2$ array patch antenna using microstrip line-coaxial probe feeder. The U-Slot $2{\times}2$ array patch antenna were fabricated on the PEC using press-technique that is based on the simulation results. And the Anritsu 37169A vector network analyzer has been used in measurement of a prototype antenna. As a result, it was measured that the superior characteristic of wideband showing approximately 1 GHz ($5.110 GHz{\sim} 6.142 GHz$) of input return loss (VSWR < 2) in resonant frequency of 5 GHz band. And the antenna gain is 13 dBi, in both the E-plane and H-plane measured at 5.15 GHz, 5.35 GHz, 5.50 GHz, and 5.87 GHz.