• Journal of Sensor Science and Technology
• /
• v.14 no.2
• /
• pp.78-84
• /
• 2005

A contactless recharging device for totally implantable middle ear systems has been designed as a pillow type that the user can recharge the implanted battery with taking a rest. The proposed device uses the electromagnetic coupling between the transmitting coil and the receiving coil. To supply sufficient power for the implanted circuits, each coil uses LC resonance and the implanted device uses voltage doubler. A power MOSFET is used for switching the DC voltage of LC parallel circuit and the switching frequency demands on a programmable frequency generator which is controlled by microcontroller. In order to improve the electromagnetic coupling efficiency at specific positions of coil which may vary with the displacement of head, the optimal location of receiving coil was studied, and the 5 transmitting coils in a pillow for recharging the implant module was designed. From such a recharging experiment, it was found that the proposed device could provide the sufficient operating voltage within the distance of 4 cm between pillow and the implanted device.

• Journal of the Korean Magnetic Resonance Society
• /
• v.23 no.4
• /
• pp.87-92
• /
• 2019

Allium hookeri (Liliaceae) has been received the increasing attention as a bioactive resource due to its potent biological activities including anti-oxidant, anti-obesity, anti-microbial and lipid-regulating activities. The beneficial effects of A. hookeri are known contributed from the high content of organosulfur compounds in A. hookeri. Though a variety of articles demonstrated that A. hookeri contains 'saponin' as a bioactive constituent, the scientific evidence to prove it was limited. In the present study, we have attempted to identify saponin contained in A. hookeri through chromatographic isolation and NMR spectroscopic methods. As a result, a spirostane-type steroidal saponin (1) has been successfully isolated from the methanolic extract of A. hookeri roots. The structure of 1 was elucidated by extensive 1D and 2D spectroscopic methods including ¹H-NMR, ¹³C-NMR, ¹H-¹H COSY, HSQC, HMBC and NOESY; identified as (3β, 22R, 25S)-spirost-5-en-3yl O-6-deoxy-α-L-mannopyranosyl-(1→4)-O-6-deoxy-α-L-mannopyranosyl-(1→4)-O-[6-deoxy-α-L-mannopyranosyl-(1→2)]-β-D-gluco pyranoside. 1 showed the significant inhibitory activity on mushroom tyrosinase with IC₅₀ values of 248.7 μM while the inhibition on alpha-glucosidase was not significant.

• Bulletin of the Korean Chemical Society
• /
• v.22 no.4
• /
• pp.395-400
• /
• 2001

The effects of ortho- (R = H and CH3) and Y-substituents (Y = OCH3, CH3H and CN), which are directly attached to the carbonyl carbon, on the protonation equilibria of the para-X-substituted benzoyl derivatives, 4-X -2, 6-di-R-C6H2-C(=O)-Y, are investigated theoretically using the B3LYP method with 6-31+G* basis set. Structurally, both of the (B) and (BH+ ) forms in the species with R = H are nearly coplanar regardless of the Y-substituents implying that the steric repulsion between Y-substituent and R = H is relatively small. In the species with R = CH3 , the tortional angle (Θ) between the carbonyl moiety and aryl ring varies from zero to near right angle depending on the degree of steric repulsion between Y and R = CH3 and the resonance demand. However the reaction energies, ΔG°, for the protonation processes are more favorable for R = CH3 than for R = H due to stronger electron donating effect of R = CH3 , although the species with R = CH3 are unfavorable sterically. On the other hand, the Hammett type plots are progressively better correlated with б+ than with б values on going from Y = OCH3 to Y = CN for both species with R = H and CH3 indicating that the degree of resonance delocalization between carbonyl moiety and X-substituent is increased for a more electron accepting Y-substituent. Nevertheless the effects of R = CH3 on the magnitude of Hammett type reaction constants ( б or б+ ) are not much different from those of R = H.

• Journal of Biomedical Engineering Research
• /
• v.40 no.1
• /
• pp.1-6
• /
• 2019

Human mesenchymal stem cells (hMSC) are multipotent stromal cells that have great potential to differentiate into a variety of cell types such as osteocytes, chondrocytes, and myocytes. Although there have been many studies on their clinical availability, little is known about how intracellular signals can be modulated by topographic features of the extracellular matrix (ECM). In this study, we investigated whether and how microwavy-patterned extracellular matrix (ECM) could affect the signaling activity of focal adhesion kinase (FAK), a key cellular adhesion protein. The fluorescence resonance energy transfer (FRET)-based FAK biosensor-transfected cells are incubated on microwavy-patterned surfaces and then platelet derived growth factor (PDGF) are treated to trigger FAK signals, followed by monitoring through live-cell FRET imaging in real time. As a result, we report that PDGF-induced FAK was highly activated in cells cultured on microwavy-patterned surface with L or M type, while inhibited by H type-patterned surface. In further studies, PDGF-induced FAK signals are regulated by functional support of actin filaments, microtubules, myosin-related proteins, suggesting that PDGF-induced FAK signals in hMSC upon microwavy surfaces are dependent on cytoskeleton (CSK)-actomyosin networks. Thus, our findings not only provide new insight on molecular mechanisms on how FAK signals can be regulated by distinct topographical cues of the ECM, but also may offer advantages in potential applications for regenerative medicine and tissue engineering.

• Journal of the Korean Electrochemical Society
• /
• v.22 no.2
• /
• pp.53-59
• /
• 2019

To examine the solution structure of electrolytes, it is very important to understand ion-ion and ion-solvent interactions. In this review, we introduce the basic principle of dielectric relaxation spectroscopy (DRS) and studies of electrolyte structure. DRS is a type of impedance method, which measures the dielectric properties of electrolytes over a high frequency domain at levels of tens of GHz. Therefore, DRS provides information on the different polar chemical species present in the electrolyte, including the type and concentration of free solvents and ion pairs with dipole moments. The information of DRS is complementary to the information of conventional analytical techniques (Infrared/Raman spectroscopy, nuclear magnetic resonance (NMR), etc.) and thus enables a broad understanding of electrolyte structure.

• Journal of Biomedical Engineering Research
• /
• v.43 no.5
• /
• pp.319-330
• /
• 2022

In this study, the optimal driving frequency was derived through finite element analysis (FEA) to optimize the developed piezoelectric ultrasonic medical devices(PUMD) for bone surgery. The core of the PUMD is the piezoelectric ceramic (PZT), which is a vibrator that generates vibration energy. The piezoelectric ceramic shows the maximum current value with respect to the input voltage at the resonance frequency, which generates the maximum mechanical vibration. In the past, various studies have been conducted related to the analysis of PUMD, but most of the research so far has been limited to free vibration analysis. However, in order to derive the accurate resonant frequency, the initial stress generated by bolt tightening in the bolt-clamped Langevin type transducer (BLT) must be considered. In this study, after designing a PUMD, the driving performance according to the bolt tightening value was analyzed through FEA, and this was experimentally verified. First, the resonance mode and frequency response were confirmed through modal and harmonic analysis at 20-40 kHz, which is known as the optimal driving frequency band of PUMD for bone surgery. In addition, the design of the PUMD was confirmed by checking the mechanical behavior of the tip and the piezoelectric ceramic at the resonant frequency. Consequentially, the characteristic evaluation was performed, and it was confirmed that the resonant frequency result derived through the FEA was reasonable. Through this study, we presented a more rational FEA method than before for BLT transducers. We expect that this will shorten the time and cost of developing a PUMD, and will enable the development of more stable and high-quality products.

• Maxillofacial Plastic and Reconstructive Surgery
• /
• v.28 no.4
• /
• pp.310-319
• /
• 2006

Submucosal type cleft palate is subdivision of the cleft palate. It is very difficult to find submucosal cleft, because when we exam submucosal type cleft palate patients, it seems to be normal. But in fact, there are abnormal union of palatal muscles of submucosal type cleft palate patients. Because of late detection, the treatment - for example, the operation or the speech therapy - for the submucosal type cleft palate patient usually becomes late. Some patients visited our hospital due to speech disorder nevertheless normal intraoral appearance. After precise intraoral examination, we found out submucosal cleft palate. We evaluated the speech before and after surgery of these patients. In this study, we want to find the objective characteristics of submucosal type cleft palate patients, comparing with the normal and the complete cleft palate patients. Experimental groups were 10 submucosal type cleft palate patients and 10 complete cleft palate patients who got the operation in our hospital. And, the controls were 10 normal person. The sentence patterns using in this study were simple 5 vowels. Using CSL program we evaluated the Formant, Bandwidth. We analized the spectral characteristics of speech signals of 3 groups, before and after the operation. In most cases, the formant scores were higher in experimental groups (complete cleft palate group and submucosal type cleft palate group) than controls. There were small differences when speeching /a/, /i/, /e/ between experimental groups and control groups, large differences when speeching /o/, /u/. After surgery the formant scores were decreased in experimental groups (complete cleft palate group and submucosal type cleft palate group). In bandwidth scores, there were no significant differences between experimental groups and controls.

• Journal of Korean Neurosurgical Society
• /
• v.49 no.2
• /
• pp.102-106
• /
• 2011

Objective : Although there are several explanations for a duplicated middle cerebral artery (DMCA), its embryological origin is still an open question. We reviewed these anomalous vessels to postulate a theory of their different origins, sizes, and courses. Methods : A retrospective review of 1,250 cerebral angiographies, 1,452 computed tomography (CT)-angiographies, and 2,527 magnetic resonance (MR)-angiographies was performed to identify patients with DMCA. Results : Twenty-five patients had 25 DMCAs. Conventional angiography detected nine patients with DMCA (9/1250, 0.72%), MR-angiography detected seven patients with DMCA 0.28%), and CT-angiography detected nine patients with DMCA (9/1452, 0.62%). The DMCAs originated near the internal carotid artery terminal in eight patients (type A), and between the origin of the anterior choroidal artery and the terminal internal carotid artery in 17 patients (type B). The diameters of the eight type A DMCAs were the same or slightly smaller than those of the other branch of the DMCA. All type A DMCAs showed a course parallel to that of the other branch of the DMCA. The diameters of the 17 type B DMCAs were the same, slightly smaller, or very much smaller than that of the other branch of the DMCA. Nine type B DMCAs showed parallel courses, and the other eight curved toward the temporal lobe. Conclusion : The two branches of the type A DMCAs can be regarded as early bifurcations of the MCA. The branches of the type B DMCAs had parallel courses or a course that curved toward the temporal lobe. The type B DMCA can be regarded as direct bifurcations of the MCA trunk or the early ramification of the temporal branch of the MCA.

• Journal of Periodontal and Implant Science
• /
• v.40 no.5
• /
• pp.239-243
• /
• 2010

Purpose: The purpose of this study was to evaluate the effects of implant shape and bone preparation on the primary stability of the implants using resonance frequency analysis. Methods: Sixty bovine rib blocks were used for soft and hard bone models. Each rib block received two types of dental implant fixtures; a straight-screw type and tapered-screw type. Final drilling was done at three different depths for each implant type; 1 mm under-preparation, standard preparation, and 1 mm over-preparation. Immediately after fixture insertion, the implant stability quotient (ISQ) was measured for each implant. Results: Regardless of the bone type, the ISQ values of the straight-screw type and tapered-screw type implants were not significantly different (P>0.05). Depth of bone preparation had no significant effect on the ISQ value of straight-screw type implants (P>0.05). For the tapered-screw type implants, under-preparation significantly increased the ISQ value (P<0.05), whereas overpreparation significantly decreased the ISQ value (P<0.05). Conclusions: Within the limitations of this study, it is concluded that bone density seemed to have a prevailing effect over implant shape on primary stability. The primary stability of the tapered-screw type implants might be enhanced by delicate surgical techniques.

• Journal of the Korean Society for Precision Engineering
• /
• v.4 no.1
• /
• pp.65-73
• /
• 1987

In recent days, the application of ultrasonics has been increased in the field of engineering and medicine. The ultrasonic hardness tester to apply the principle of contact compliance method is entirely different from hardness tester in the past and in the practical use, the more pre- cisive measurement is required because it has a slight change of hardness value due to the difference of resonance frequency. Therefore, in this study, as one type of applicative transducers which can detect the optimum pressure load, ring type load cell was used in the measurement of ultrasonic hardness. From experimental results, it was compared ultrasonic hardness testing method with the other hardness testing methods. Also, the measurement error of ultrasonic hardness tester could be measured within .+-. 0.5 HRC F.S. in the case of 3.0Kg pressure load.