• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2008년도 추계학술대회 논문집 Vol.21
• /
• pp.29-29
• /
• 2008

Platinum Thin films were deposited on $Al_2O_3$ by Rf magnetic Sputtering. The physical and electrical characteristics of these films were analyzed under various deposition conditions(Ar gas pressure, input power, substrate temperature.) and annealing condition. The deposition rate was increased with increasing the input power but not increased linear. In the other factor, The Pt thin films property was associated with resistance. so lower resistance had more and more good Pt thin films condition. For the purpose of this study, we will get the best Pt thin film characteristics.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1993년도 추계학술대회 논문집
• /
• pp.85-89
• /
• 1993

Silicone oil exhibits the properies of both organic and inorganic substances and, thus, it has many superior properties such as higher thermal resistance and lower thermal oxidation level when compared to other dielectric liquids. In order to investigate the dielectric characteristics, dielectric liquids of viscosity 1 [cSt] is chosen as the specimen and experiment is performed in the temperature range of 20∼65 [$^{\circ}C$] and frequency range of 30∼1${\times}$10$\^$6/ [Hz] respectively. As a result, the observed linear decrease in dissipation factor at the frequency range below 3 [kHz] is due to the influence of frequency, whereas the increase in dissipation factor at higher frequency range is contributed by electrode's resistance. At a fixed frequency of 30 [kHz], increasing temperature results in higher peak value and wide width of the absorption curve. This is due to the increase in dipole and viscosity. As temperature increases, dipole moment is decreased from 0.98 to 0.64 [debye]. The activation energy which causes the relaxation and loss of dielectric is obtained about 15 [kcal/mole].

• 대한조선학회논문집
• /
• 제48권2호
• /
• pp.134-140
• /
• 2011

The present paper deals with characteristics of resistance performance according to the variation of synthetic ice thickness and hull form. The resistance test has been conducted with pack ice condition in Pusan National University towing tank. Waterline angle has been chosen as a main parameter for the variation of hull form characteristics, which is the most important factor especially in icebreaking cargo vessel. The serial comparisons of resistance test have been done with the variation of hull form parameter as well as with the different thickness of synthetic ice. The different trend of resistance performances with increasing of waterline angle has been shown at each synthetic ice thickness. The present test results is expected to be confirmed by comparing the test results in ice tank in the near future.

• 대한의생명과학회지
• /
• 제18권2호
• /
• pp.146-151
• /
• 2012

Urinary tract infection (UTI) is one of the most common bacterial infections and is predominantly caused by uropathogenic Escherichia coli (UPEC). UPEC strains generally possess several genes encoding virulent factors, which are mostly adhesins, toxins, bacteriocin and siderophores. E. coli is composed of four main phylogenetic group (A, B1, B2, D) and virulent extra-intestinal strains mainly belong to groups B2 and D. Prescription of ciprofloxacin, a kind of fluoroquinolone group antibiotics, is increasing now a days, but resistance to this drug is also increasing. A total of 188 strains of E. coli were collected. Thirteen strains were collected from healthy students in 2011 and 175 strains from patients with urinary tract infection in 2010. Virulence factor genes (papC, fimG/H, sfaD/E, hlyA, cnf1, and usp) were amplified by polymerase chain reaction (PCR) methods for phylogenetic group (A, B1, B2, D) detection. Ciprofloxacin susceptibility test was performed by disk diffusion method. The identified virulence factors (VFs), phylogenetic groups and ciprofloxacin resistance in 13 E. coli strains isolated from healthy students were papC (15.4%), fimG/H (76.9%), sfaD/E (30.8%), hlyA (23.1%), cnf1 (23.1%), usp (7.7%), phylogenetic group A (23%), B1 (8%), B2 (46%), D (23%) and ciprofloxacin resistance (7.7%), while those of in 175 E. coli strains isolated from patients with UTI were papC (41.1%), fimG/H (92.5%), sfaD/E (30.3%), hlyA (10.3%), cnf1 (30.3%), usp (27.4%), phylogenetic group A (9.1%), B1 (5.1%), B2 (60.6%), D (25.1%) and ciprofloxacin resistance (29.7%). In this study, 10 out of 13 E. coli strains (76.9%) from healthy students were found to possess more than one virulence factor associated with adhesion. In addition, one E. coli strain isolated from healthy students who had never been infected with UPEC showed ciprofloxacin resistance. According to these results between the virulence factors and phylogenetic groups it was closely associated, and UPEC strains isolated from patients showed high level of ciprofloxacin resistance.

• 한국전기전자재료학회논문지
• /
• 제15권8호
• /
• pp.671-677
• /
• 2002

In this study, the high frequency SMD ceramic resonators with the size of $3.7{\times}3.1{\times}0.385\textrm{mm}^3$ were fabricated using $Pb_{0.88}(La_{0.6}Nd_{0.4})_{0.08}(Mn_{1/3}Sb_{2/3})_{0.02}Ti_{0.98}O_3$ ceramics with the variations of electrode radius size. With increasing the electrode radius size, resonant resistance in third overtone mode was decreased and electromechanical coupling factor($k_{t3}$) in third overtone mode was showed constant values. Taking into consideration mechanical quality factor($Qm_{t3}$) of 5,552 and dynamic range(D.R) of 60.72dB in third overtone mode, the ceramic resonator with the electrode radius size of $\theta$1.13mm was suitable for 20MHz resonator application.

• 콘크리트학회논문집
• /
• 제17권3호
• /
• pp.455-464
• /
• 2005

수중불분리성 콘크리트의 적용 사례가 점차 증대되고 있는 추세임에도 불구하고 역사가 짧은 탓으로 신뢰성 등에 대한 문제점을 지적하고 있다 특히 수중불분리성 콘크리트는 동결응해에 대한 저항성이 매우 취약한 것으로 알려져 있어 일본토목학회에서는 동결융해작용을 받는 지역에서는 사용해서는 않된다고 규정하고 있다. 본 연구에서는 수중불분리성 콘크리트의 내구성을 향상시키기 위한 목적으로 광물질혼화재 3종류로 제조한 수중불분리성 콘크리트의 기초물성과 동결응해 저항성에 대한 실험을 실시하였다. 본 연구실험결과 FA20 및 SG50의 유동성 및 장기강도는 기준콘크리트 보다 양호한 경향을 보인 반면 현탁물질량은 약간 큰 값을 나타내었다. 한편 MK10의 경우, 빠른 수화반응으로 현탁물질량과 압축강도는 양호한 결과를 나타내었으나 유동성은 다소 떨어지는 문제점이 있었다. 한편, 수중불분리성 콘크리트의 동결응해 저항성은 셀룰로오스계 수중불분리성 혼화제에 의한 크고 불규칙한 갇힌공기 때문에 광물질혼화재를 혼합한 경우에도 효과가 적었으나 SG50과 MK10의 공기량 $6{\pm}0.5\%$의 경우, 동결응해 저항성이 약간 향상되는 결과를 얻었다. 그러나 고로슬래그 미분말의 분말도를 달리한 경우 분말도가 증가할수록 활성도가 높아져 동결응해 저항성이 향상되는 경향을 나타내었다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1995년도 추계학술대회 논문집
• /
• pp.221-223
• /
• 1995

The electrical conductivity of SnO$_2$added ZnO was investigated using the DC and AC methods. The electrical conductivity of SnO$_2$added ZnO was decreased with increasing the concentration of SnO$_2$. The cal쳐lated effective dielectric constants of 3 mol%, 5 mo1%, and 7 mol% are ~7, ~13, and ~120, respectively. The factor of the decrease for the electrical conductivity seems to be the increase of the resistance of grain decreasing the size of grain.

• 한국방재학회:학술대회논문집
• /
• 한국방재학회 2011년도 정기 학술발표대회
• /
• pp.91-91
• /
• 2011

The quality of the surface layer in concrete structures plays an important role in the durability of the concrete. The concrete factory products are made as they improve the appearance of the surface and compressive strength in need. A common criterion to judge the quality of concrete products frequently seen in our daily life appears to be "beauty" in terms of consistent shaping. However, as for most concrete curb in such areas where a large amount of anti-freezing agents(NaCl) and ice and snow melting agents(CaCl2) are spread over roads to ensure road safety during the winter season, since deterioration advances from the surface, scaling is seen on the surface concrete due to deterioration which combined freezing damage and salt damage. Especially, In cold northern districts, the spreading amount of deicing salts increases by regulation of studded tire use, and the scaling of the concrete products, the various parts of concrete structures for roads is increasing in recent years. In this study, L-shape concrete curb were targeted, the permeable form method with the commercial permeable sheet was applied to it and the improvements of the quality were examined. By the permeable form method, surface layers got strengthened, which prevented permeation of the deterioration factor from the outside, and the scaling resistance of the upper surface where the permeable sheet was applied improved exceedingly. It will be expected by applying the permeable form method to various concrete products that frost resistance improves and scaling damage decreases.

• 한국염색가공학회지
• /
• 제23권1호
• /
• pp.43-50
• /
• 2011

Electrically conductive yarn coated with silver particles are widely used to make smart wear but recent studies on smart fabrics are focused on measuring method of electrical characteristics and improving technologies of its electric properties. Also durability of conductive yarn with environmental change was also important work to make smart fabric. We compared resistance changes of silver coated conductive yarns under various physical and chemical conditions such as repeated strain, heat exposure and pH for basic informations on smart wear manufacturing process. And we deduct that repeated strain among the physical conditions was most effective factors on yarn resistance change and the low resistance change was observed with increasing the number of filaments in identical yarn fineness.

• 동력기계공학회지
• /
• 제14권6호
• /
• pp.83-88
• /
• 2010

The wear behavior of epoxy matrix composites filled with nano sized silica particles is discussed in this paper. Especially, the variation of the coefficient of friction and the wear resistance according to the change of apply load and sliding velocity were investigated for these materials. Wear tests of pin-on-disc mode were carried out and the wear test results exhibited as following ; The epoxy matrix composites showed lower coefficient of friction compared to the neat epoxy through the whole sliding distance. As increasing the sliding velocity the epoxy matrix composites indicated lower coefficient of friction, whereas the neat epoxy showed higher coefficient of friction as increasing the sliding velocity. The specific friction work of both materials were increased with apply load. In case of the epoxy matrix composites, the running in periods of friction were reduced as increase in apply load. The epoxy matrix composites were improved the wear resistance by adding the nano silica particles remarkably. It is expected that the load carrying capacity of the epoxy matrix composites will be improved by increase of Pv factor.