• 대한의용생체공학회:의공학회지
• /
• 제18권1호
• /
• pp.1-8
• /
• 1997

This study was performed to evaluate the effect of resin and filler type on the compressive strength of light-activated composite resins. Experimental composite resins containing either amorphous spherical silica or crushed quartz in two matrix resins of BisGMA/TEGDMA and UTMA/TEGDMA were prepared and the specimens of 3 m in diameter and 6m in length were made. Compressive test was subjected to a crosshead speed of 0.5 mm/min, and the fracture surFaces were examined by SEM. The compressive strength of UTMA-based composite resin was higher than that of BisGMA-based composite resin. The loading rate of spherical silica was higher than that of crushed silica when the size dis- tribution of fillers was same. Strength decrease of Bis-GMA-based composite resin was severer than that of UTMA-based composite resin in a $37^{\circ}$c water environment. Fracture surface showed that the composite resin failure developed along the matrix resin and the filler/resin interface region.

• 대한치과보철학회지
• /
• 제46권2호
• /
• pp.105-115
• /
• 2008

전치부 영역에서의 복합 레진을 이용한 수복물의 표면은 착색과 치태 침착이 적어야 하며 치은 조직에 좋은 내성을 갖도록 평활해야 한다. 레진 수복 후 여러 마무리 방법중 blade를 이용한 방법은 치은과 접해있는 변연 부위의 불필요한 레진을 제거하고 마무리하는데 있어 치은 손상을 최소화하면서 간편하게 이용할 수 있는 방법이다. 본 연구의 목적은 현재 많이 사용되고 있는 nano-hybrid composite resin과 ormocer-based compostie resin 간의 여러 가지 마무리 방법에 있어 blade를 이용한 방법과 polishing을 시행한 경우의 표면 거칠기 및 nano계열과 ormocer 계열 복합 레진의 표면 특징을 비교하는 것으로 실험을 위해 가로 6mm, 세로 3mm, 높이 2mm의 금속 주형을 이용하여 레진 블록을 형성하고 대조군은 상면에 mylar strip을 위치시켜 광중합 하였으며, Ormocer - based composite resin ($Admira^{(R)}$)과 nanohybrid composite resin ($Grandio^{(R)}$)에서는 blade를 이용한 경우와 rubber polishing을 이용한 경우를 실험군으로 하였고, ormocer-based flowable composite resin ($Admira^{(R)}$ Flow)과 nanohybrid flowable composite resin ($Grandio^{(R)}$ Flow)에서는 blade를 이용한 경우, rubber polishing을 이용한 경우와 추가적으로 아무것도 시행하지 않은 경우를 실험군으로 하였다. 레진 블록의 표면은 profilometer 및 SEM을 이용하여 거칠기 및 조도를 비교하였으며 통계분석 하였다. 실험 결과 mylar stirp을 적용한 경우 Ra (${\mu}m$) 평균 값은 ormocer-base composite resin이 $0.25{\mu}m$, ormocer-based flowable resin $0.17{\mu}m$, nanohybrid composite resin $0.24{\mu}m$, nanohybrid flowable resin $0.18{\mu}m$ 였으며 blade를 적용한 경우 평균 값은 각각 $0.43{\mu}m$, $0.37{\mu}m$, $0.48{\mu}m$, $0.41{\mu}m$ 였다. 가장 낮은 Ra (${\mu}m$)은 mylar stirp을 적용한 시편에서 얻어졌으며, blade를 이용한 마무리 방법과 rubber polishing을 시행한 경우와 표면 거칠기 비교시 Ra (${\mu}m$)값에서 통계적으로 유의한 차이를 보이지 않았다 (P>0.05). Nanohybrid composite resin이 blade로 마무리하거나 rubber polishing후 ormocer-based composite resin보다 표면 거칠기 증가율이 좀 더 큰 것을 알 수 있었다. 이상의 결과는 blade를 이용한 마무리 방법이 다른 마무리 방법을 대체할 수 있을 것이라는 것을 보여주며, 이에 따라 본 실험 결과에 한정지어 볼 때 복합레진 수복후 마무리 방법으로 blade를 이용하여 시행하는 것이 적용가능 할 것이라 생각된다.

• Restorative Dentistry and Endodontics
• /
• 제26권4호
• /
• pp.316-325
• /
• 2001

The purpose of this study was to evaluate the effect of adhesive curing timing on the direction of polymerization shrinkage of light-curing composite resin. In this study, the curing times of adhesive and composite resin were measured by differential scanning calorimeter(DSC). 28 extracted human molars were embedded in clear resin and box-type cavities were prepared. Based on DSC data, the experimental teeth were divided into 4 groups. Group 1: no bond; Group 2: late curing; Group 3: Intermediate curing; Group 4: Early curing. After treating with adhesive, the buccal cavities were filled with Z-100 hybrid composite resin and the lingual ones were filled with AEliteflo flowable composite resin. The depressions at the surface were measured by surface profilometer, then the specimens were embedded in clear resin and sectioned. Impressions were obtained and used to get epoxy resin replicas. The epoxy replicas were gold-coated and observed under SEM. Average Maximum Gap(AMG), Gap Proportion(GP), Average Marginal Index(AMI) were used to compare the shrinkage gap of each group. The results were statistically analyzed using the Kruskal-Wallis One Way ANOVA, Student-Newman-Keuls method. The results of this study were as follows. 1. Average Maximum Gap, Gap Proportion, Average Marginal Index and depression at the surface or Z-100 hybride composite resin were smaller than those of AEliteflo flowable composite resin(P<0.05). 2. When the bonding between composite resin and tooth structure was strong, the shrinkage gap was small, and depression at the surface was deep(P<0.05). 3. In the well-bonded group, light-curing composite resin shrank toward bonded cavity wall, not toward light source. The result suggested that the direction of polymerization shrinkage was affected by the quality of bonding in the dentin-resin interface. The strong was the bonding between composite resin and tooth structure, the smaller was the gap and the deeper was the depression at the surface. Then the flow to compensate the polymerization shrinkage proceeded from surface to bonded cavity wall.

• 대한치과의사협회지
• /
• 제50권7호
• /
• pp.368-376
• /
• 2012

The demand for tooth-colored restorations has grown considerably during the last decade. Posterior composite restorations have risen in popularity as a result of the development of improved resin composites, bonding systems and operating techniques. A major limitation of direct composite restoration is the difficulty of controlling the polymerization shrinkage. To overcome this limitation, the indirect fabrication of a composite restoration and cementation with resin cement has been advocated. Unfortunately, the current available resin cements with indirect restorations do not always bond to dentin as strongly as dentin adhesive systems bond with direct resin composite restorations. Several procedural strategies have been proposed for indirect composite restoration. In this regard, the rationale for the indication, characteristics and clinical application is described in this paper. As a result, we will try to suggest the evidence-based guidelines for indirect composite restorations by reviewing each available indirect composite products, technical procedure and pronosis.

• International Journal of Aerospace System Engineering
• /
• 제4권1호
• /
• pp.9-12
• /
• 2017

In this study, an investigation on mechanical properties of flax natural fiber composite is performed as a precedent study on the design of eco-friendly structure using flax natural fiber composite. The Vacuum Assisted Resin Transfer Molding-Light (VARTML) manufacturing method is adopted for manufacturing the flax fiber composite panel. The VARTML is a manufacturing process that the resin is injected into the dry layered-up fibers enclosed by a rigid mold tool under vacuum. In this work, the resin flow analysis of VARTM manufacturing method is performed. A series of flax composite panels are manufactured, and several kinds of specimens cut out from the panels are tested to obtain mechanical performance data. Based on this, structural design of chemical storage tank for agricultural vehicle was performed using flax/vinyl ester. After structural design and analysis, the resin flow analysis of VARTM manufacturing method was performed.

• International Journal of Aerospace System Engineering
• /
• 제1권1호
• /
• pp.21-28
• /
• 2014

In this study, an investigation on mechanical properties of flax natural fiber composite is performed as a precedent study on the design of eco-friendly structure using flax natural fiber composite. The Vacuum Assisted Resin Transfer Molding-Light (VARTML) manufacturing method is adopted for manufacturing the flax fiber composite panel. The VARTML is a manufacturing process that the resin is injected into the dry layered -up fibers enclosed by a rigid mold tool under vacuum. In this work, the resin flow analysis of VARTM manufacturing method is performed. A series of flax composite panels are manufactured, and several kinds of specimens cut out from the panels are tested to obtain mechanical performance data. Based on this, structural design of chemical storage tank for agricultural vehicle was performed using flax/vinyl ester. After structural design and analysis, the resin flow analysis of VARTM manufacturing method was performed.

• Restorative Dentistry and Endodontics
• /
• 제35권2호
• /
• pp.69-79
• /
• 2010

본 연구는 여러 레진 시멘트의 film thickness에 따른 상아질과 간접 레진 수복물 간의 미세인장 결합 강도를 측정하고, 각 레진 시멘트의 중합 수축 및 굴곡 강도, 탄성 계수를 비교 분석하며, 접착 계면 및 파단면의 주사전자 현미경 관찰을 통하여 레진 시멘트의 film thickness가 레진 간접 수복물의 접착 효율에 미치는 영향을 평가하고자 시행하였다. 복합 레진형 레진 시멘트인 Variolink II와 Duo-Link, 접착형 레진 시멘트인 Panavia F와 Rely X Unicem의 4가지 레진 시멘트를 사용하였고, 각각의 시멘트를 film thickness에 따라 < $50\;{\mu}m$ (control)의 대조군과 $50\;{\mu}m$ (T50), $100\;{\mu}m$ (T100), $150\;{\mu}m$ (T150)의 실험군으로 나누어 총 16개의 군으로 분류하였다. 데이터는 ANOVA와 Duncan's multiple comparison test (p < 0.05)를 이용하여 통계 분석하였으며 다음과 같은 결론을 얻었다; 1. Variolink Ⅱ는 모든 film thickness에서 접착형 레진 시멘트보다 높은 결합 강도를 나타냈지만(p < 0.05), Duo-Link는 대조군을 제외하고는 통계학적 유의차가 없었다(p > 0.05). 2. Film thickness가 증가할수록 복합 레진형 레진 시멘트의 결합 강도는 유의성 있게 감소(p < 0.05)하는 경향을 보인 반면, 접착형 레진 시멘트는 통계학적 유의차가 없었다(p > 0.05). 3. Panavia F는 통계학적으로 유의성 있게 낮은 중합 수축량을 나타냈다(p <0.05). 4. 굴곡 강도와 탄성 계수는 복합 레진형 레진 시멘트가 접착형 레진 시멘트보다 유의성 있게 높게 나타났다(p < 0.05). 5. FE-SEM 관찰 결과 결합 강도가 높은 복합 레진형 레진 시멘트는 균일한 접착층과 잘 발달된 resin tag 소견을 보였으나, 접착형 레진 시멘트는 불분명한 접착층과 resin tag 소견을 나타냈다. 파단면 관찰에서 복합 레진형 레진 시멘트는 혼합형 파괴 양상을 나타냈으나 접착형 레진 시멘트는 접착성 파괴 양상을 나타냈다.

• Restorative Dentistry and Endodontics
• /
• 제39권4호
• /
• pp.310-318
• /
• 2014

Objectives: This study examined the influence of the resin thickness on the polymerization of silorane- and methacrylate-based composites. Materials and Methods: One silorane-based (Filtek P90, 3M ESPE) and two methacrylate-based (Filtek Z250 and Z350, 3M ESPE) composite resins were used. The number of photons were detected using a photodiode detector at the different thicknesses (thickness, 1, 2 and 3 mm) specimens. The microhardness of the top and bottom surfaces was measured (n = 15) using a Vickers hardness with 200 gf load and 15 sec dwell time conditions. The degree of conversion (DC) of the specimens was determined using Fourier transform infrared spectroscopy (FTIR). Scratched powder of each top and bottom surface of the specimen dissolved in ethanol for transmission FTIR spectroscopy. The refractive index was measured using a Abbe-type refractometer. To measure the polymerization shrinkage, a linometer was used. The results were analyzed using two-way ANOVA and Tukey's test at p < 0.05 level. Results: The silorane-based resin composite showed the lowest filler content and light attenuation among the specimens. P90 showed the highest values in the DC and the lowest microhardness at all depth. In the polymerization shrinkage, P90 showed a significantly lower shrinkage than the rest two resin products (p < 0.05). P90 showed a significantly lower refractive index than the remaining two resin products (p < 0.05). Conclusions: DC, microhardness, polymerization rate and refractive index linearly decreased as specimen thickness linearly increased. P90 showed much less polymerization shrinkage compared to other specimens. P90, even though achieved the highest DC, showed the lowest microhardness and refractive index.

• Composites Research
• /
• 제28권1호
• /
• pp.6-14
• /
• 2015

치아의 수복에 사용되는 재료인 Methacrylate 기질 복합레진(Clearfil AP-X)과 Silorane 기질 복합레진(Filtek P90)을 대상으로 스트레인게이지법과 FEM 분석법으로 중합수축응력거동을 분석하였다. 또한 복합레진의 탄성계수와 수축변형률을 중합수축응력과 관계시켜 이론식을 제시하고 이 식의 계산결과와 FEM 분석법의 결과를 비교하였다. 스트레인 게이지법으로 측정한 결과, 중합수축응력의 최대값은 Clearfil AP-X가 Filtek P90 보다 약 2.8배 높게 나타났다. FEM 분석 결과, Von-Mises 응력은 복합레진 수복재와 PMMA 링사이의 계면부에서 최대로 되었으며 시편표면의 계면부가 내부보다 응력집중이 더 컸음을 알았다. 예측식을 통한 반경 방향의 수축응력은 평면응력상태의 FEM 분석법을 통한 값과 비교하여 오차 5% 이내로 정확했음을 확인하였다.

• Advanced Composite Materials
• /
• 제18권2호
• /
• pp.167-185
• /
• 2009

Environmental problems caused by extensive use of polymeric materials arise mainly due to lack of landfill space and depletion of finite natural resources of fossil raw materials like petroleum or natural gas. The substitution of synthetic petroleum-based resins with natural biodegradable resins appears to be one appropriate measure to remedy the above-mentioned situation. This study presents the development of a composite that uses environmentally degradable starch-based resin as matrix and natural mineral basalt fibres as reinforcement, and investigates the fibre's and the composite's mechanical properties. The tensile strength of single basalt fibres was verified by means of single fibre tensile tests and statistically investigated by means of a Weibull analysis. Prepreg sheets were manufactured by means of a modified doctor blade system and hot power press. The sheets were used to manufacture specimens with fibre volume contents ranging from 33% to 61%. Specimens were tested for tensile strength, flexural strength and interlaminar shear strength. Composites manufactured during this study exhibited tensile and flexural strength of up to 517 MPa and 157 MPa, respectively.