• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1997년도 추계학술대회 논문집
• /
• pp.585-590
• /
• 1997

Conventional foaming process has defects such as lower mechanical properties than ur~foaming material due to non-uniform cell distribution and environmental pollution problem caused by chemical blowing agency. So, a new foaming process such as Microcelluar plastics has been introduced to use inactive gases as a foaming agency. In order to apply Microcellular plastics for mass production process system such as extrusion, injection molding and blow molding, it needs to predict the change in material properties of polymer according to the amount of meltingas. In Polymer molding applying Microcelluar plastics, the change of viscosity among several material properties is the most important factor. Therefore, this paper is aimed to establish the method which not only finds out but also predicts the change of viscosity of ABS(Acrylonitri1e Butadiene Styrene) resin according to inert gas amount in extrusion molding.

• Tribology and Lubricants
• /
• 제16권1호
• /
• pp.1-8
• /
• 2000

Friction and wear tests have been performed on nylon, acetal resin, and PTFE (polytetrafluoroethylene), in reciprocating dry sliding conditions against steel discs. According to the results, acetal resin showed the lowest wear rates and PTFE exhibited the lowest friction coefficient. The prominent wear mechanisms found were adhesion and abrasion.

• 한국안전학회지
• /
• 제22권3호
• /
• pp.22-27
• /
• 2007

The knowledge of the flash point of the various liquid substances is required because of process safety and control in industrial fire protection. The epoxy resin is one of versatile resins that has wide selection of using curing agents and additives to achieve various applications such as coatings, adhesives, interior materials, reinforced plastics and electrical insulation. In this study, the lower flash points for p-xylene+epoxy resin, o-xylene+epoxy resin and n-butanol+epoxy resin systems were measured by using Pensky-Martens closed cup tester. The lower flash points for p-xylene+epoxy resin, o-xylene+epoxy resin and n-butanol+epoxy resin systems rapidly increased 80wt%, 90wt% and 95wt% of epoxy resin concentration, respectively. This results serve as a guide to estimate flash point of any epoxy resin solution.

• Design & Manufacturing
• /
• 제15권2호
• /
• pp.1-10
• /
• 2021

In this study, the current state of the plastics industry has been examined. The direction of development and innovation is reviewed and commented. The technical statuses of various sectors such as thermoplastic resin, composite material, mold engineering, and simulation have been scrutinized. In addition, the industrial status of each sector has been reviewed. Then, the challenges that the plastics manufacturing industry has to deal with have been discussed. Especially, the situation in Republic of Korea has been elaborated in detail. Based on the discussion, an open innovation strategy has been suggested. It has been argued in this work that the open innovation strategy will enables efficient funding and development by avoiding resource consuming rent seeking.

• 비파괴검사학회지
• /
• 제34권2호
• /
• pp.141-147
• /
• 2014

경제성과 함께 다양한 기능성으로 유리 및 금속제를 대체하고 있는 고분자 합성수지인 플라스틱(plastic) 재료의 열화(thermal degradation) 및 열적 특성을 비파괴적으로 평가하기 위하여 초음파의 전파특성(속도 및 감쇠)이 사용되었다. 플라스틱 재료중 범용 열가소성 재료인 높은 투명도의 아크릴 수지(PMMA)에 대해 유리전이온도($T_g$) 범위내에서 열화온도 및 열화시간에 따른 다양한 열화시편에 대해 전파특성 변화가 측정되었다. 열화가 진전될수록 감쇄는 증가하였고 속도는 감소함을 보였으며, 초음파 전파특성의 측정을 통해 열가소성 플라스틱 재료의 정량적 열화평가 및 유리전이온도($T_g$) 영역의 정성적 추정이 가능하였다.

• 자원리싸이클링
• /
• 제26권1호
• /
• pp.69-77
• /
• 2017

폐소형가전의 재활용 공정에서 발생하는 플라스틱류 중 검정색 플라스틱의 경우 재질 선별이 어려워 혼합물의 형태로 저급 재활용 되고 있다. 본 연구에서는 검정색 플라스틱의 재질별 선별을 위하여 비중선별, 정전선별, 근적외선 선별 및 IR/Raman 분광법 등 기존 선별 기술의 검토를 통하여, 현장 적용에 대한 문제점 및 제한사항을 확인하였다. 검정색 플라스틱의 재질선별에 대한 기술적 한계를 극복하기 위하여 레이저유도붕괴분광법(Laser Induced Breakdown Spectroscopy, LIBS)을 이용하여 검정색 플라스틱의 각 재질별 LIBS 스펙트럼을 분석하였으며, 정규화 과정을 수행한 후 차원축소 알고리즘인 주성분 분석(Principal Component Analysis, PCA)을 수행하였다. 또한, 검정색 플라스틱의 각 재질별 LIBS 스펙트럼 분석 및 주성분 분석을 통하여 향후 재질별 인식 및 선별 기술의 현장적용을 위해서는 추가적으로 해결해야 할 문제점을 확인하였다. 검정색 플라스틱의 재질별 인식의 정확성 및 선별효율의 향상을 위하여 지능형 알고리즘 분야의 연구를 통하여 효율이 우수한 분류기를 설계하고 분류기의 성능 및 신뢰도 향상을 위한 연구가 추가적으로 진행되어야 할 것으로 사료된다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2003년도 추계학술대회 논문집 Vol.16
• /
• pp.235-238
• /
• 2003

Thermo-plastic has generally bad electrical characteristics at high temperature comparing to thermoset-plastics when the plastic apply to electrical power apparatus as an electrical insulator. To solve the problem, we study engineering plastics such as Polyamide and Polyphthalamide as a base resin. And filler of the engineering plastics is glass fiber. Electrical characteristics studied are permittivity, loss factor and breakdown strength according to temperature and frequency of measuring signal. Electrical characteristics of Polyphthalamide has good temperature and frequency dependency comparing to those of Polyamide.

• Advanced Composite Materials
• /
• 제16권2호
• /
• pp.181-194
• /
• 2007

This paper presents the mechanical properties of a composite consisting of acrylonitrile-butadiene-styrene (ABS) resin mixed with carbon fiber reinforced plastics (CFRP) pieces (CFRP/ABS). CFRP pieces made by crushing CFRP wastes were utilized in this material. Nine kinds of CFRP/ABS compounds with different weight fraction and size of CFRP pieces were prepared. Firstly, tensile and flexural tests were performed for the specimens with various CFRP content. Next, fracture surfaces of the specimens were microscopically observed to investigate fracture behavior and fiber/resin interface. Finally, the tensile modulus and strength were discussed based on the macromechanical model. It is found that the elastic modulus increases linearly with increasing CFRP content while the strength changes nonlinearly. Microscopic observation revealed that most carbon fibers are separated individually and dispersed homogeneously in ABS resin. Epoxy resin particles originally from CFRP are dispersed in ABS resin and seem to be in good contact with surrounding resin. The modulus and strength can be expressed using a macromechanical model taking account of fiber orientation, length and interfacial bonding in short fiber composites.

• 한국해양공학회지
• /
• 제23권2호
• /
• pp.98-103
• /
• 2009

The resin infusion method is the latest technology of FRP laminating and cleaning to improve FRP hull quality. This method is focused on how to arrange infusion channels for the laminiating strategy. The laminating strategy using the resin infusion method has been utilized to complete the infusion work and remove the cavities on the FRP surface within the curing time. It is resulting from the arrangement of infusion and vacuum channels, the resin property, and the combination of FRP. This strategy has been depended on the field experience for manufacturing FRP without the resin infusion simulation. This study can help to improve the efficiency of FRP fabrication with the laminating strategy including the resin infusion simulation instead of the field experience.

• 한국신뢰성학회:학술대회논문집
• /
• 한국신뢰성학회 2005년도 학술발표대회 논문집
• /
• pp.303-305
• /
• 2005

Recently, various plastics are used for improvement of reliability and thermal stability of electronic goods. But, it is difficult to choose suitable balance of grade resin to each other product property. Selection of high efficiency resin is becoming inescapable circumstance according to change of reflow temperature of product and development of product following to lead free. Using a inexpensive and reasonable resin, that sustain a uniform performance of product quality. It is make a robust product and increase a company's competitive power. Hereupon, I introduce example that use ESPI methods of thermal deformation analysis of product using in our company product. I try to refer to a structural weak point detection of real time measurement of electronic parts instead of mechanical and chemical measurement of specimen type.