• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 추계학술대회논문집A
• /
• pp.93-98
• /
• 2001

Fatigue strength evaluation was carried out for the core support structure of a low voltage circuit breaker. The impact load acting on the core support was calculated based on the strains measured during operation. A three-dimensional finite element analysis was performed to determine local peak stresses for fatigue evaluation. Fatigue safety factors were calculated using the modified Goodman, Gerber, Soderberg, and modified Findley lines, considering the magnitude of the residual stress and impact load.

• 소성∙가공
• /
• 제25권2호
• /
• pp.136-140
• /
• 2016

Although the finite element method is a good tool to analyze skin-pass rolling, it is hard to be applied in the field because of its long calculation time. In the current study, simple numerical models were developed for the prediction of roll force and residual stress profiles along the strip width. These models are based on finite element analysis and a coupled solution of Sims’ equation and Hitchcock’s formula. The results indicate that plastic strains can be represented as in simple equations of the deformed roll profile and the initial thickness of the strip.

• 한국해양공학회:학술대회논문집
• /
• 한국해양공학회 2006년 창립20주년기념 정기학술대회 및 국제워크샵
• /
• pp.213-216
• /
• 2006

During the last decade several different methods have been proposed for the estimation of thermal deformations in the line heating process. These are mainly based on the assumption of residual strains in the heat-affected zone or simulated relations between heating conditions and residual deformations. However these results were restricted in the application from the too simplified heating conditions or the shortage of the data. The purpose of this paper is to develop a simulator of thermal deformation in the line heating using the artificial neural network. Two neural network predicting the maximum temperature and deformations at the heating line are studied. Deformation data from the line heating experiments are used for learning data for the network. It was observed that thermal deformation predicted by the neural network correlate well with the experimental result.

• International Journal of Korean Welding Society
• /
• 제1권2호
• /
• pp.45-50
• /
• 2001

This paper presents application of neutron diffraction technique to the measurement of residual stresses in the T-type 20 m thick welded stainless steel plates(100$\times$50 $mm^2$ and 50$\times$50 $mm^2$). The High Resolution Powder Diffractormeter of the Korea Atomic Research Institute was utilized in the measurement. The power of nuclear reactor was 24 MWt and the measured reflection in the 220 plane (2$\theta$）was $92.66^{\circ}$. Poisson ratio of 0.265 and elastic constant of 211 GPa were applied to the calculation of stresses and strains. Three directional components such as normal, transverse, and longitudinal stresses were measured. The results showed that three components were tensile and became compressive along the y axis in the zone away from the welded center. The compressive stresses became tensile in the zone away from the center line of x axis. This may be due to the balance effect caused by the net stress to keep the specimen shape flat.

• 농업과학연구
• /
• 제11권1호
• /
• pp.25-33
• /
• 1984

This experiment carried out to obtain the thermophilic yeast, suitable for ethanol fermentation, and two usable strain were isolated. And microbial characteristics of these strains were investigated, and ethanol fermentation tested. The results obtained were as follows; 1. The selected yeasts were identified D-71 with Saccharomyces cerevisiae, and J-515 with Saccharomyces fermentati. 2. The strains D-71 and J-515 were showed the highest ethanol fermentation activity in the crushed corn mash of high concentration at $35^{\circ}C$, and showed the slightly lower at $40^{\circ}C$ than in the case of $35^{\circ}C$. 3. The strains D-71 and J-515 were showed the very higher ethanol fermentation activity than that of compared strain at $35^{\circ}C$ and $40^{\circ}C$, and at these temperature, fermentation period was a little bit of short. 4. On fermentation test using D-71 and J-515, the residual total sugar in the mash was very lower at $35^{\circ}C$.

• 한국해양공학회지
• /
• 제13권3호통권33호
• /
• pp.68-76
• /
• 1999

The welding residual stresses produced by the welding frequently caused a crack and promote stress corrosion etc. in HAZ(heat affected zone) contained with external load and weakness of material. Therefore, PWHT(post welding heat treatment) is widely used to reduce wekdubg residuss, to relax hardening of heat affected zone and to get rid of impurity. In this study, in order to define the effect on shappes of T-welded joint, during the post welding heat treatment, we have carried out numerical analyses on the several test pieces by using computer program which was based on thermal-elasto-plato-plasto-creep theories for the study. The main results obtained form this study is as follows: 1) The mechanical difference for change the thickness of plate and groove angle did not appear. 2) The distribution modes of welding residual stresses are same on the all test specimens during the post welding heat treatment. 3) In a mecharical point of view, minimum groove groove angle($40^{circ}$) is more suitable than maximum groove angle($60^{circ}$). 4) Therefore, it is appropriate to minimize the size of groove shape in strength and safety.

• Geomechanics and Engineering
• /
• 제16권5호
• /
• pp.463-469
• /
• 2018

In offshore engineering, lateral cyclic loading may induce excessive lateral movement and bending strain in pile foundations. Previous studies mainly focused on deformation mechanisms of single piles due to lateral cyclic loading. In this paper, centrifuge model tests were conducted to investigate the response of a $2{\times}2$ pile group due to lateral cyclic loading in clay. After applying each loading-unloading cycle, the pile group cannot move back to its original location. It implies that residual movement and bending strain are induced in the pile group. This is because cyclic loading induces plastic deformation in the soil surrounding the piles. As the cyclic load increases from 62.5 to 375 kN, the ratio of the residual to the maximum pile head movements varies from 0.30 to 0.84. Moreover, the ratio of the residual to the maximum bending strains induced in the piles is in a range of 0.23 to 0.82. The bending strain induced in the front pile is up to 3.2 times as large as that in the rear pile. Thus, much more protection measures should be applied to the front piles to ensure the serviceability and safety of pile foundations.

• Journal of Dairy Science and Biotechnology
• /
• 제39권3호
• /
• pp.104-112
• /
• 2021

This study was conducted to evaluate the efficacy of commercial disinfectants at inactivating Enterobacter sakazakii (Cronobacter spp.) in water. Disinfectant I contained 6.15% sodium hypochlorite, and disinfectant II contained both 2.25% n-alkyl dimethylbenzyl ammonium chloride and 2.25% n-alkyl ethylbenzyl ammonium chloride. Disinfectant I was added to distilled water to obtain a range of residual chloride concentrations at 50 ppm intervals with a maximum of 1-1,000 ppm. Disinfectant II was prepared at concentrations ranging from 1-200 ppm with 5 ppm intervals. Exposure time for all solutions was 10 min. In total, 58 E. sakazakii (Cronobacter spp.) strains were tested in this study. Nine isolates were obtained from clinical samples, and 49 isolates were obtained from environmental samples. Seven strains (6 clinical and 1 environmental) were able to survive in 100 ppm disinfectant I, and a maximum of 5 ppm of disinfectant II. Fifty one strains (3 clinical and 48 environmental) were not killed in 10 ppm of disinfectant I and 1 ppm of disinfectant II in water. In conclusion, this study demonstrated that clinical E. sakazakii (Cronobacter spp.) strains displayed 5- to 10-fold higher resistance to disinfectants than environmental E. sakazakii (Cronobacter spp.) strains. Disinfectant II, containing quaternary ammonium compounds, was shown to be more potent in inactivating E. sakazakii (Cronobacter spp.) in water used to clean infant formula manufacturing equipment than disinfectant I.

• 대한기계학회논문집A
• /
• 제26권9호
• /
• pp.1787-1794
• /
• 2002

TiNi alloy fiber was used to solve the problem of the tensile residual stress as the reinforced material. TiNi alloy fiber improves the tensile strength of composite by occurring compressive residual stress in the matrix using shape memory effect. In order to generate compressive residual stress in TiNi/Al6061 shape memory alloy(SMA) composite, 1, 3 and 5% pre-strains were applied to the composite in advance. It was also evaluated the effect of compressive residual stress corresponding to the pre-strain variation and the volume fraction of TiNi alloy. AE technique was used to clarify the microscopic damage behavior at high temperature and the effect of pre-strain in TiNi/Al6061 SMA composite. The results of the microscopic damage evaluation of TiNi/Al6061 SMA composite under various pre-strain using AE technique can be divided into three stage corresponding to the AE signals. AE counts and events were useful parameters to evaluate the fracture mechanism according to the variation of pre-strain. In addition, two dimensional AE source location technique was applied for monitoring the crack initiation and propagation in composite.

• 비파괴검사학회지
• /
• 제22권1호
• /
• pp.45-52
• /
• 2002

금속복합재료 (MMC) 내부에서의 강화재와 기지재사이의 열팽창계수의 차이에 의해 발생하는 인장잔류응력은 복합재료의 인장강도를 저하시키는 심각한 문제중의 하나이다. 따라서 본 연구에서는 TiNi/A16061 형상기억복합재료내부의 인장잔류응력의 문제를 해결하기 위하여 강화재로써 TiNi 합금을 사용하였다. TiNi 합금은 형상기억효과를 이용하여 복합재료내부에 압축잔류응력을 발생시킴으로써 인장강도를 증가시키는 역할을 한다. 복합재료내부에 압축잔류응력을 발생시키기 위하여 예변형(pre-strain)을 가하였다. 본 연구에서는 예변형의 변화에 따른 압축잔류응력의 영향을 평가하였으며 AE 기법을 이용하여 고온에서의 복합재료의 미시적 손상거동과 예변형의 영향을 평가하였다.