최근의 건축 구조물이 고층화, 대형화됨에 따라 초고강도 콘크리트의 적용 및 수요가 증가하고 있는 추세이나, 화재에 대한 취약성을 가지고 있는 초고강도 콘크리트의 열적 특성에 대한 검토는 아직 충분하지 않으며 이에 대한 성능 검토 또한 요구되고 있는 실정이다. 이에 이 논문에서는 초고강도 콘크리트의 고온 재료 모델 개발에 대한 기초적 자료를 제공하기 위하여 상온에서 $800^{\circ}C$까지의 고온 가열을 받은 100 MPa급 초고강도 콘크리트를 대상으로 가열온도의 변화에 따른 잔존압축강도, 탄성계수 및 응력-변형 성상, 반복하중 시의 응력-변형 성상 등 역학적 특성 변화를 확인하였다. 또한, TG/DTA분석과 SEM 촬영으로 콘크리트의 화학 물리적 특성을 확인하고 국내 외의 기존 연구와 비교 검토하였다. 그 결과, 가열온도 $300^{\circ}C$에서 잔존압축강도 및 탄성계수의 급격한 저하를 확인하였으며, 반복하중 하에서는 가열온도 $400^{\circ}C$부터 소성거동이 발생하는 것과 함께 단일하중과 거의 동일한 경향을 보임을 확인할 수 있었다. TG/DTA 분석 및 SEM 촬영을 실시한 결과와 기존 연구를 비교 검토한 결과, 콘크리트 내부 조직의 열화와 수분 증발 및 화학반응 등으로 인하여 잔존압축강도 및 탄성계수의 저하가 일어났음을 확인할 수 있었다.
재료에 가해지는 하중에 따른 변형정도를 측정하는 연속압입시험은 비파괴적으로 재료의 기계적 물성을 직접 평가할 수 있는 기법으로, 하충의 범위에 따라 macro, micro 그리고 nano의 세 범위로 나눌 수 있다. Macro 범위는 kgf 영역에서 사용되어, 국부 영역의 인장물성과 신뢰성 저하의 주요 원인인 잔류응력을 구할 수 있으며, 최근에는 국내기술에 의해 관련 기기와 기술이 개발되었다. 산업구조물, 사용중인 배관 등 기존 시험법으로는 평가하기 힘든 소재의 신뢰성 평가에 많은 활용이 이루어지고 있다. Micro 범위는 gf 영역으로, macro 범위보다 높은 분해능에 의해 용접부 등 물성 구배가 존재하는 재료에 사용된다. 한편 mgf 영역의 극미소하중에 적용되는 nanoindentation technique은 기본적으로 경도와 탄성계수를 구할 수 있으며, 잔류응력, 인장물성 등을 유도하는 연구가 진행중이다. 반도체 재료, 다 상 재료, 바이오 소재 등에서 많은 활용이 이루어지고 있으며, 그 수요가 급격히 증가하고 있는 추세이다. 이러한 연구 들올 바탕으로 하여 국제 표준 규격 및 국내 표준 규격의 제정이 추진 중이다.
콘크리트는 고온에 강한재료로 인식되어 왔으나, 화재 등의 고온에 의해 내부조직의 물리 화학적 변화가 발생해 역학적 특성이 저하하게 된다. 이에, 고온시 콘크리트의 역학적 특성의 저하에 관한 연구보고 및 기준이 제시되고 있다. 그러나 고강도 콘크리트 및 하중을 재하한 상태에 관한 연구데이터는 적다. 따라서 이 연구에서는 고온 및 하중재하에 따른 고강도 콘크리트의 고온특성을 평가하였다. W/B 12.5%, 14.5%, 20%의 고강도 콘크리트를 대상으로 비재하상태 및 $0.25f_{cu}$의 하중조건을 설정하여, 고온시의 응력-변형, 최대하중에서의 변형, 압축강도, 탄성계수, 열팽창변형, 단기 고온크리프을 평가하였다. 실험 결과, 압축강도가 높아질수록 가열에 의한 압축강도의 저하가 크게 나타났고, $500^{\circ}C$이상의 온도에서 고온에 의한 열팽창변형과 하중재하에 의한 수축변형이 상쇄되어 압축강도 및 탄성계수의 잔존율이 높아지는 것을 확인할 수 있었다.
In this study, unidirectional and plain woven carbon fiber reinforced magnesium matrix composite laminates were fabricated by the liquid pressing infiltration process, and evolutions of the microstructure and compressive strength of the composite laminates under corrosion were investigated by static immersion tests. In the case of the unidirectional composite laminate, the main microstructural damage during immersion appeared as a form of corrosion induced cracks, which were formed at both CF/Mg interfaces and the interfaces between layers. On the otherhand, wrap/fill interface cracks were mainly formed in the plain woven composite laminate, without any cracks at the CF/Mg interface. The formation of these cracks was considered to be associated with internal thermal residual stress, which was generated during cooling after the fabrication process of these materials. As a consequence of the corrosion induced cracks, the thickness of both laminates increased in directions vertical to the fibers with increasing immersion time. With increasing immersion time, the compressive strengths of both composite laminates also decreased continuously. It was found that the plain woven composite laminates have superior corrosion resistance and stability under a corrosive condition than unidirectional laminates.
방전 플라즈마 소결법을 적용하여 $Al_2O_3$-SiC 나노 복합체를 150$0^{\circ}C$ 이하의 온도에서 완전치밀화를 이루었다. 제조된 $Al_2O_3$-SiC 복합체는 이상 결정립 성장 없이 매우 균질한 미세구조를 형성하고 있는데, 첨가된 SiC 입자는 주로 결정립 내 및 결정립계에 존재하면서 $Al_2O_3$기지상에서 결정립 성장을 억제하는데 매우 유호하였음을 확인 할 수 있다. 한편, SiC 입자의 첨가는 크랙 회절 및 브릿징 등에 의해서 유도된 재료 강도 및 인성 강화 기구에 의해서 $Al_2O_3$-SiC 복합체의 기계적 물성을 크게 향상시켰다.
Kim, Hyung-Chul;Lee, Dong-Jin;Kweon, Oh-Seong;Kim, Ik-Jin
한국세라믹학회지
/
제42권8호
/
pp.532-536
/
2005
Thermal shock resistance of structural ceramics is a property that is difficult to quantity, and as such is usually expressed in terms of a number of empirical resistance parameters. These are dependant on the conditions imposed, but one method that can be used is the examination of density, Young's modulus and thermal expansion retention after quenching. For high temperature applications, long-annealing thermal durability, cycle thermal stability and residual mechanical properties are very important if these materials are to be used between $1000^{\circ}C$ and $1300^{\circ}C$. In this study, an excellent thermal shock-resistant material based on $Al_2TiO_5-mullite$ composites of various compositions was fabricated by sintering reaction from the individual oxides and adjusting the composition of $Al_2O_3TiO_2/SiO_2$ ratios. The characterization of the damage induced by thermal shock was done by measuring the evolution of the Young's modulus using ultrasonic analysis, density and thermal expansion coefficients.
In general, spot welding is used at no welding rod or flux for the process, low welding point temperature compared to arc welding, short heating time, less damage to the parent material, and low deformation and residual stress, relatively. Also, because of the pressurization effect, better mechanical qualities of the welding parts are obtained. Therefore, in various fields of industry its rapid operation speed can make mass production possible such as motor industry. In FEM analysis for the spot welding process, it is effective to use simple modeling rather than complicated one because of its numerous number of spots and reduction of analysis time. Therefore, this study provides with not only simplification of modeling analysis by using beam component composition of structure without re-compositing the spot welding point mesh but also modeling analysis of which property of fracture strength is reflected. In addition complete spot welding model is examined at rectangular post shape (hat shape) by impact test, compared the results, and verified its validity. As a result, it is possible to optimize the welding position and to recognize the strength of structure and the proposed equal distance model shows the effect of welding point reduction and improvement of stiffness.
Two kinds of multifilament Bi-2223/Ag tapes, which are different in the precursor calcination temperatures, were heat treated for different time (12, 20, 30, 50, 70, or 100 h) firstly to obtain varied B2223 contents, and then followed by the same pressing and sintering cycles. The relation of the 2223 phase contents after the first sintering and the transport property of the fully processed tapes was studied. The results show that 75-80% 2223 phase formed in tapes before the first cold pressing is beneficial to get a high $I_{c}$ in the final tapes. Compensating the total heat treatment time of the tapes first sintered for 20 h to the same length as that first sintered for 50 h in the subsequent sintering stages, different $I_{c}$ enhancements were observed in these two tapes. No improvement on $I_{c}$ was found in the tape made from the powder calcined at higher temperature, whereas for the tape prepared with the lower temperature calcined powder, the $I_{c}$ was increased to the same level as that first sintered for 50 h. The 2223 contents before the intermediate mechanical work is related to the residual reactants, especially to the liquid phase, which is of vital importance to the phase conversion and healing microcracks, meanwhile, to the size and distribution of the non-superconducting secondary phases. The lower temperature calcined powder resulted in slow formation of 2223 phase, but also provided more reactants and liquid phase for the further phase conversion, as a consequence, for the Improvement of $I_{c}$. c/.
발전설비 구조물은 기대 수명동안의 안전성을 확보하기 위하여 정해진 규격에 부합하도록 설계하여 건설된다. 하지만 가동 중 다양한 복합 환경에 노출됨에 따라 구조물을 이루고 있는 재료의 열화 현상이 가속화 되어 예상하지 못한 파손이 발생할 수 있기 때문에, 용접부와 같은 구조물의 취약부에 대하여 기계적 물성을 정확하게 측정하는 기술은 안전과 직결되는 필수적인 연구 분야이다. 인장시험 등의 기존의 역학물성 측정 시험법들은 특정 크기의 시편을 요구하고 파괴적인 시험이기 때문에 가동 중 구조물에 적용하는 것이 불가능하였다. 이러한 한계점을 극복하고자 비파괴적이고 간편한 방법으로 다양한 역학물성 평가가 가능한 연속압입시험법이 각광받는 시험법으로서 연구되고 있다. 본 연구에서는 연속압입시험에서 압입자 하부에 발생하는 응력장 해석을 기반으로 하여 인장물성 및 잔류응력을 평가할 수 있는 최신 기법을 소개한다. 또한, 원전 구조물의 취약부로 알려진 용접부에 대하여 실험을 수행하여 산업상에서 연속압입시험이 건전성 평가에 유용하게 적용할 수 있음을 확인하였다.
일반사출성형은 공정 중 보압단계에서 캐비티에 높은 압력이 작용하여 성형품에 큰 잔류응력이 남게 된다. 또한 캐비티 내 위치 별로 압력분포가 달라 균일한 물성의 제품을 얻는데 한계가 있다. 다수 개 빼기 일반사출성형에서는 캐비티간 충전 불균형이 일어나 캐비티간 품질의 편차를 일으킨다. 이와 같은 한계를 극복하기 위해 사출압축성형 공정을 사용하는 경우가 많다. 본 연구에서는 다수 개 캐비티를 갖는 금형을 이용하여 일반사출성형과 사출압축성형을 비교 분석하였다. 실험과 해석을 통하여 연구를 수행하였으며 투명한 수지인 PC와 PS를 이용하여 시편에 나타나는 복굴절을 관찰하여 일반사출성형과 사출압축성형에서 나타나는 성형특성을 비교하였다. 연구결과, 사출 압축성형으로 제작된 시편에서 캐비티 내의 압력이 균일하여 복굴절과 성형수축률이 낮고 균일하게 나타났다. 그리고 일반사출성형에서 나타나는 캐비티간 충전 불균형에 의한 캐비티간 물성의 편차가 사출압축성형에서는 크게 줄어들었다. 본 연구를 통하여 사출압축성형은 다수 개 빼기 사출성형에서 캐비티 내 균일한 물성확보뿐만 아니라 캐비티간 품질 불균형을 해소하는데 유용함을 확인할 수 있었다.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.