• Journal of Welding and Joining
• /
• v.5 no.1
• /
• pp.73-80
• /
• 1987

During PWHT, it is well known that residual stress in weld HAZ is one of the reasons for PWHT embitterment. In case of static loading, it was experimentally found that fracture toughness of weld HAZ was dependant upon PWHT conditions. However, the effects of PWHT on fatigue behavior are not clearly verified. Therefore, in this paper, the effects of heating rate PWHT conditions and residual stress simulated in weld HAZ of Cr-Mo steel on fatigue crack propagation behavior were evaluated by fatigue Testing and SEM observation. The obtained results are summarized as follows; 1. Applied stress($10 Kgf/mm^2$) in weld HAZ during PWHT tneded to decrease fatigue strength and to increase fatigue crack growth rate. 2. Applied stress and slow heating rate of 60.deg. C/hr during PWHT contributed to precipitin of impurity elements as well as carbide, which promoted the fatigue crack growth. 3. Fatigue crack growth rate decreased at the heating rate of 220.deg. C/hr in contrast with 600.deg. C/hr and 60.deg. C/hr.

• Structural Engineering and Mechanics
• /
• v.63 no.2
• /
• pp.251-257
• /
• 2017

A local damage identification method using measured structural static displacement is proposed in this study. Based on the residual force vector deduced from the static equilibrium equation, residual strain energy (RSE) is introduced, which can localize the damage in the element level. In the case of all the nodal displacements are used, the RSE can localize the true location of damage, while incomplete displacement measurements are used, some suspicious damaged elements can be found. A model updating method based on static displacement response sensitivity analysis is further utilized for accurate identification of damage location and extent. The proposed method is verified by two numerical examples. The results indicate that the proposed method is efficient for damage identification. The advantage of the proposed method is that only limited static displacement measurements are needed in the identification, thus it is easy for engineering application.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.262.2-262.2
• /
• 2014

Plasma processing is an essential process for pattern etching and thin film deposition in nanoscale semiconductor device fabrication. It is necessary to maintain plasma chamber in steady-state in production. In this study, we determined plasma chamber state with residual gas analysis with self-plasma optical emission spectroscopy. Residual gas monitoring of fluorocarbon plasma etching chamber was performed with self-plasma optical emission spectroscopy (SPOES) and various chemical elements was identified with a SPOES system which is composed of small inductive coupled plasma chamber for glow discharge and optical emission spectroscopy monitoring system for measuring optical emission. This work demonstrates that chamber state can be monitored with SPOES and this technique can potentially help maintenance in production lines.

• Smart Structures and Systems
• /
• v.17 no.2
• /
• pp.347-361
• /
• 2016

A two-stage method for damage detection in truss systems is proposed. In the first stage, a modal residual vector based indicator (MRVBI) is introduced to locate the potentially damaged elements and reduce the damage variables of a truss structure. Then, in the second stage, a differential evolution (DE) based optimization method is implemented to find the actual site and extent of damage in the structure. In order to assess the efficiency of the proposed damage detection method, two numerical examples including a 2D-truss and 3D-truss are considered. Simulation results reveal the high performance of the method for accurately identifying the damage location and severity of trusses with considering the measurement noise.

• ETRI Journal
• /
• v.37 no.4
• /
• pp.780-786
• /
• 2015

This paper describes an audio source separation that is based on nonnegative matrix factorization (NMF) and expectation maximization (EM). For stable and highperformance separation, an effective auxiliary source separation that extracts source residuals and reprojects them onto proper sources is proposed by taking into account an ambiguous region among sources and a source's refinement. Specifically, an additional NMF (model) is designed for the ambiguous region - whose elements are not easily represented by any existing or predefined NMFs of the sources. The residual signal can be extracted by inserting the aforementioned model into the NMF-EM-based audio separation. Then, it is refined by the weighted parameters of the separation and reprojected onto the separated sources. Experimental results demonstrate that the proposed scheme (outlined above) is more stable and outperforms existing algorithms by, on average, 4.4 dB in terms of the source distortion ratio.

• Economic and Environmental Geology
• /
• v.24 no.3
• /
• pp.245-260
• /
• 1991

Surficial dispersion patterns of heavy metals and toxic elements (U, Mo, Cu, Zn, Fe, Mn, Co, Cr, V, Ni, Pb, and Cd) were investigated in the Dukpyungri, Goesan area covered with low grade uranium-bearing black shales. Maximum abundance of U in the black shale was 455ppm. Radioactivity was counted at a maximum of 7cps in black shales, and was less than 0.5cps in shales, slates, and oil shales of the control areas. Enrichment of Mo, V, Cu, Zn, Cd, and Pb in black shales is particularly characteristic compared with shales, slates, and oil shales of the control areas, whereas contents of Mn, Cr, Co, and Th in all rock samples tend to be almost similar. Residual top soils (0~15cm depth) over black shales show high contents of Mo, Cu, Zn, Ni, Cd, and V in comparison with the control areas. Contents of trace elements in subsoils (15~30cm depth) were higher about one and half times than those in topsoils. Average contents of Mo, Cu, Pb, Zn, Cd and V in garden soil and playground soil of an elementary school in Dukpyungri, Goesan area, were high about two to fifteen times compared with the control areas. Contents of trace elements in stream sediments were higher from two to eight times than those in residual soils. Sodium, AI, K, V, Cr, and Fe were more enriched in the roots of pine than in the twigs of pine. Contents of Li, AI, V, Ni, Cd, Fe, and Co were higher in the roots of azalea than in the twigs of azalea. Enrichment of P, Ca, and Mg was remarkable in the twigs of both pine and azalea. Biological absorption coefficients for essential elements (Zn, P, Mn, Ca and K)tend to be high, whereas those for the non-essential elements.(Ba, Ti, V, and Mo) and toxic elements(Cr, Co, Pb and Ni) be low. Less mobile elements (Pd, Cd, and Co) tend to show anomalies with higher contrast than more mobile elements(Mo, V, Zn, Cu and Ni) in the area covered with black shales.

• Economic and Environmental Geology
• /
• v.29 no.4
• /
• pp.495-508
• /
• 1996

This study had three purposes: (1) to investigate dispersion and enrichment level of potentially toxic elements; (2) to identify uranium-bearing minerals in black shales; and (3) to assess the chemical speciation of heavy metals in soils and sediments. Rock, surface soil and stream sediment samples were collected in the Chungjoo area covered with black shales in Korea. These samples were analyzed for multi-elements using INAA and ICP-AES. The maximum abundance of U in black shales is 56 ppm and radioactivity counts up to 240CPM. Molybdenum, V, Ba, Cu, and Pb are enriched in black shales and most of soils show high concentrations of U, Mo, Ba, Cu, Pb and Zn. Concentrations of potentially toxic elements decrease in the order of mountain soil > farmland soil > paddy soil. Enrichment index of soils and sediments are calculated and higher than 1.0 in the black shale area with the highest value of 6.1. In order to identify U-bearing minerals, electron probe micro analysis was applied, and uraninite and brannerite in black shale were found. Uraninite grains are closely associated with monazite or pyrite with the size of $2{\mu}m$ to $10{\mu}m$ in diameter whereas brannerite occurs as $50{\mu}m$ euhedral grains. With the results of sequential extraction scheme, residual fractions of Cu, Pb and Zn in soils are mainly derived from weathering of black shale but Cu, Pb and Zn in sediments are present as non-residual fractions. Lead is predominantly present as oxidizable phase in soils whereas Zn is in exchageable/water-acid soluble phase in sediments.

• Journal of Oral Medicine and Pain
• /
• v.23 no.2
• /
• pp.193-209
• /
• 1998

In identifying bodies that are severely decayed or damaged, methods using fingerprints and various biochemical tests are known to have its limits. To overcome this, forensic odontological method which is based on the analysis of the cranium, tooth and dental restoration is used to enhance the accuracey of individual identification. For this reason, I have come to analysis of the dental materials that exists between the teeth that is perceived to have been previously restored and the one adjacent to it. By analyzing the constituents of gold crown-restored, non-precious metal-restored, gold inlay-restored and amalgam -restored teeth, and adjacent teeth using EDX(energy dispersive X-ray microanalysis) which was invented to analyze very small amount of elements, the nature of the restoration could be predicted and the results obtained were as follows. 1. Some of constitute of gold alloy was extracted from residual cement of gold crown restoration, but that was not extracted from the restored tooth and the one adjacent to it. 2. Some of constituents of non-precious metal alloy was extracted both in the residual cement on the tooth with no-precious metal restoration and in the tooth with the restoration itself. However, none of its constituents were found in the tooth adjacent to it. 3. Some of constituents of gold alloy were found in the residual cement of gold inlay, but they were not found in the restored tooth and the adjacent tooth. 4. Some of constituents of amalgam alloy were found both in tooth restored with amalgam and in the adjacent tooth. From the results obtained above, it is possible to utilize the data obtained from analyizing residual dental materials in a more effective way. This data compensates for the lost data due to any harm done to the restorations prior to individual identification and further enhances the accuracy. Therefore, it could be concluded that this process of analyzing residual dental materials could be beneficial to individual identification in the area of forensic odontoldogy.

• Steel and Composite Structures
• /
• v.25 no.5
• /
• pp.617-624
• /
• 2017

In this study, a new empirical method is presented to obtain Dynamic Increase Factor (DIF) in nonlinear static analysis of structures against sudden removal of a gravity load-bearing element. In this method, DIF is defined as a function of minimum ratio of difference between maximum moment capacity ($M_u$) and moment demand ($M_d$) to plastic moment capacity ($M_p$) under unamplified gravity loads of elements. This function determines the residual strength of a damaged building before amplified gravity loads. For each column removal location, a nonlinear dynamic analysis and a step-by-step nonlinear static analysis are carried out and the modified empirical DIF formulas are derived, which correspond to the ratio min $[(M_u-M_d)/M_p]$ of beams in the bays immediately adjacent to the removed column, and at all floors above it. Therefore, the new DIF can be used with nonlinear static analysis instead of nonlinear dynamic analysis to assess the progressive collapse potential of a moment frame structure. The proposed DIF formulas can estimate the real residual strength of a structure based on critical member.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.29 no.9 s.240
• /
• pp.1169-1174
• /
• 2005

Imprint lithography is a promising method for high-resolution and high-throughput lithography using low-cost equipment. In particular, ultraviolet-nanoimprint lithography (UV-NIL) is applicable to large area imprint easily. We have proposed a new UV-NIL process using an elementwise patterned stamp (EPS), which consists of a number of elements, each of which is separated by channel. Experiments on UV-NIL are performed on an EVG620-NIL using the EPS with 3mm channel width. The replication of uniform sub 70 nm lines using the EPS is demonstrated. We investigate the nonuniformity of residual layer caused by wafer deformation in experiment with varying wafer thickness. Severely deformed wafer works as an obstacle in spreading of dropped resin, which causes nonuniformity of thickness of residual layer. Numerical simulations are conducted to analyze aforementioned phenomenon. Wafer deformation in the process is simulated by using a simplified model, which is a good agreement with experiments.