• Coupled systems mechanics
• /
• 제8권3호
• /
• pp.273-287
• /
• 2019

Elastoplastic analysis of an annular disc, being fully constrained on its outer rim and interacting with a purely elastic inclusion perfectly bonded with its inner rim, is conducted to study its plastic deformation and residual stress under thermal cycles. The system is termed the composite disc. Quasi-static plane-strain deformation is assumed, and the von Mises yield criterion with or without the Ludwik hardening rule is adopted in our finite element calculations. Effects of multiple material properties simultaneously being temperature dependent on the plastic behavior of the composite disc are considered. Residual stress is analyzed from a complete loading and unloading cycle. Results are discussed for various inclusion radii. It is found that when temperature dependent material properties are considered, the maximum residual stress may be greater than the maximum stress inside the disc at the temperature-loaded state due to lower temperature having larger yield stress. Temperature independent material properties overestimate stresses inside materials, as well as the elastic irreversible temperature and plastic collapse temperature.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2006년도 춘계학술대회 논문집
• /
• pp.145-148
• /
• 2006

Cold gas dynamic spray is a relatively new coating process by which coatings can be produced without significant heating during the process. Cold gas dynamic spray is conducted by powder sprayed by supersonic gas jet, and generally called the kinetic spray or cold-spray. Cold-spray was developed in Russia in the early 1980s to overcome the defect of thermal spray method. Its low process temperature can minimize thermal stress and also reduce the deformation of the substrate. Most researches on cold-spray have focused on micro scale coating, but our research team tried to apply this method to macro scale deposition. The macro scale deposition causes deformation of a thin substrate which is usually convex to the deposited side. In this research, the main cause of the deformation was investigated using 6061-T6 aluminum alloy and properties of deposited aluminum layer such as coefficient of thermal expansion, Elastic modulus, hardness, electric conductivity were measured. From the result of the analysis, it was concluded that compressive residual stress was the main reason of substrate deformation while CTE had little effect.

• 한국CDE학회논문집
• /
• 제21권3호
• /
• pp.234-241
• /
• 2016

Conventional bent plate used in mandibular reconstruction surgery needs safety verification since its mechanical properties are changed due to the plastic deformation during the bending process. In this study we investigate stability of the plastically deformed plate and the plate with the same shape without plastic deformation through the finite element analysis(FEA). First we simulate the process of plate bending to fit the defect in patient. Then, the other plate is modelled to represent a customized plate with the same shape of the plastically deformed one, but without any residual stresses from plastic deformation. After binding these plates to the mandible, we conduct the masticatory simulation. Finally, we compare the resulting Von Mises stress of the customized plate and of the bent plate. The bent plate shows much higher stress than the customized one due to the residual stresses form the bending process. The study shows that plastic deformation in the plate may decrease the safety of the reconstruction surgery.

• 대한기계학회논문집A
• /
• 제27권4호
• /
• pp.507-514
• /
• 2003

Most of CAE analyses for injection molding have been based on the Mele Shaw's approximation: two-dimensional flow analysis. in some cases, that approximation causes significant errors due to loss of the geometrical information as well as simplification of the flow characteristics in the thickness direction. Although injection molding analysis software using three-dimensional solid elements has been developed recently, such as Moldflow Flow3D, it does not contain a deformation analysis function yet. The present work covers three-dimensional deformation analysis or injection molded plastic parts using solid elements. A numerical scheme for deformation analysis has bun proposed from the results of injection molding analysis using Moldflow Flow3D. The accuracy of the proposed approach has been verified through a numerical analysis of rectangular plates with various thicknesses in comparison with the classical shell-based approach. In addition, the reliability of the approach has also been proved through an industrial example. an optical plastic lens, in comparison of real experiments.

• 대한기계학회논문집A
• /
• 제36권4호
• /
• pp.355-360
• /
• 2012

마봉강(CD bar)은 표면조도, 치수 정밀도 그리고 진직도 등에서 우수한 특성을 가진다. 그러한 특성들로 인해 자동차 및 가전 제품의 부품으로 산업현장에서 다양하게 사용되고 있다. 산업계에서 다양하게 사용되는 마봉강 제품은 두롤 교정기를 통해 만들어지고 있으며 본 논문에서는 마봉강을 생산하는 핵심공정인 두롤 교정기 연구를 통해 롤 갭에 따른 영향을 살펴 보았다. 두롤 사이의 간격인 롤 갭의 변화는 봉강의 잔류응력과 소성변형에 많은 영향을 주는 것을 실험적으로 확인하였다. 이를 확인하기 위해 2 롤 교정 전 공정인 인발공정에서 다이 통과 후 선경 변화와 봉강 내 잔류응력분포에 대해 유한요소 시뮬레이션을 수행하였다. 두롤 교정후 잔류응력과 선경의 변화를 확인하기 위해 실험을 수행하였으며, 여기서 X 선 회절기를 이용하여 축방향 및 원주방향에서의 표면 잔류응력을 실험적으로 측정하였다.

• 비파괴검사학회지
• /
• 제34권1호
• /
• pp.18-22
• /
• 2014

용접 잔류응력은 용접공정에서 발생하는 하는데, 용접 구조물의 결함 유발 및 파괴의 주요 원인이 된다. 본 논문에서는 전자 처리 레이저 스페클 간섭법을 이용하여 원전 배관의 용접부 잔류응력을 측정하였다. 인장시험기를 이용하여 용접된 배관에 압축 하중을 가하였으며, 면내 변형 측정 간섭계를 이용하여 용접부와 모재부의 변형을 측정하였고, 제안된 수식에 의하여 탄성계수를 측정하였다. 용접 배관에 가해지는 하중에 따라 변형이 일정하게 증가하며, 용접 배관의 모재부와 용접부에 발생한 변형을 비교하였을 때, 모재부의 변형이 더 크게 나타남을 확인할 수 있었다. 용접 배관 모재부의 탄성계수는 202.46 GPa, 용접부의 탄성 계수는 212.14 GPa, 잔류응력은 6.29 MPa로 측정되었다.

• 한국지반공학회논문집
• /
• 제24권6호
• /
• pp.101-116
• /
• 2008

보강토 옹벽의 영구구조물로서의 적용성이 증가함에 따라 지속 혹은 반복하중 등 다양한 하중조건하에서 장기적인 잔류변형이 설계/시공시 주요 관점이 되고 있다. 본 연구에서는 교량구조물의 피어 및 Back-to-Back(BTB) 형태의 보강토 옹벽을 대상으로 사용하중 작용 이전에 작용시키는 선행하중이 보강토 구조물의 잔류변위를 제어에 미치는 영향을 고찰하였다. 이를 위해 모형 피어와 BTB 옹벽을 축조하여 단순재하, 지속하중, 반복하중 등 다양한 하중조건 및 시공조건에 대한 모형실험을 수행하였다. 그 결과 선행재하 공법은 다양한 하중 및 시공조건에서 잔류변위 제어에 탁월한 것으로 나타났다.

• Journal of Welding and Joining
• /
• 제33권6호
• /
• pp.60-66
• /
• 2015

Molten zone shape of pulse laser welding is affected by welding conditions such as beam power, beam speed, irradiation time, pulse frequency, etc. and is divided into conduction type and keyhole type. It is necessary to design heat source model for irradiation of laser beam in the pulse laser welding. Shape variables and the maximum energy density value of the heat source model are different depending on the molten zone shape. In this paper, pulse laser welding simulation for joining of cylindrical part and circular cover was carried out. The heat source model for pulse laser beam with circular path was applied to the heat input boundary condition, radiative and conductive heat transfer were considered for the thermal boundary condition. For each phase, thermal and mechanical properties according to temperature were also applied to analysis. Analytical results were in good agreement with the molten zone size of specimen under the same welding conditions. So, the reliability of the welding simulation was verified. Finally, the improvements for reducing residual deformation after cover welding could be reviewed analytically.

• 대한기계학회논문집A
• /
• 제24권7호
• /
• pp.1740-1747
• /
• 2000

Under repeated rolling, initial plastic deformation introduces residual stresses which render the steady cyclic state purely elastic. This is called the process of shakedown. Many studies have been done about the shakedown in semi-infinite half space using calculated Hertizian pressure. In this paper shakedown processes in a shaft are studied by finite element analyses of a two dimensional(plane strain) model with elastic-linear-kinematic-hardening-plastic material subjected to repeated, frictionless rolling contact. Symmetric and non-symmetric pressure distributions are obtained using a simplified model of the bearing-shaft assembly. The rolling contact is simulated by repeatedly translating both pressure distributions along the surface of the shaft. By the influence of the non-symmetric pressure, larger residual radial tensile stress is generated in the immediate subsurface layer, which may make a crack propagate and, the subsurface undergoes a zigzag plastic deformation during the shakedown process, which may lead to a crack initiation.

• 한국전산구조공학회:학술대회논문집
• /
• 한국전산구조공학회 2008년도 정기 학술대회
• /
• pp.331-336
• /
• 2008

An self-centering energy-dissipative (SCED) bracing system has recently been developed as a new seismic force resistant bracing system. The advantage of the SCED brace system is that, unlike other comparable advanced bracing systems that dissipate energy, such as the buckling restrained brace system, it has a self-centering capability that reduces or eliminates residual building deformations after major seismic events. In this study seismic performance of SCED braced frames is evaluated for a set of 20 design level earthquake records. According to analysis results the SCED systems showed more uniform interstory drift demand for buildings with 8 story or fewer. The residual deformation in SCED buildings turned out to be much less than that of moment-resisting frames.