• Corrosion Science and Technology
• /
• 제14권3호
• /
• pp.120-126
• /
• 2015

The usage of bending products recently have increased since many industries such as automobile, aerospace, shipbuilding, and chemical plants need the application of pipings. Bending process is one of the inevitable steps to fabricate the facilities. Induction heat bending is composed of compressive bending process by local heating and cooling. This work focused on the effect of induction heat bending process on the properties of ASME SA312 Gr. TP304 stainless steel pipes. Tests were performed for base metal and bended area including extrados, intrados, crown up, and down parts. Microstructure was analyzed using an optical microscope and SEM. In order to determine intergranular corrosion resistance, Double Loop Electrochemical Potentiokinetic Reactivation (DL-EPR) test and ASTM A262 practice A and C tests were done. Every specimen revealed non-metallic inclusion free under the criteria of 1.5i of the standard and the induction heat bending process did not affect the non-metallic inclusion in the alloys. Also, all the bended specimens had finer grain size than ASTM grain size number 5 corresponding to the grain sizes of the base metal and thus the grain size of the pipe bended by induction heat bending process is acceptable. Hardness of transition start, bend, and transition end areas of ASME SA312 TP304 stainless steel was a little higher than that of base metal. Intergranular corrosion behavior was determined by ASTM A262 practice A and C and DL-EPR test, and respectively step structure, corrosion rate under 0.3 mm/y, and Degree of Sensitization (DOS) of 0.001~0.075% were obtained. That is, the induction heat bending process didn't affect the intergranular corrosion behavior of ASME SA312 TP304 stainless steel.

• 한국물환경학회지
• /
• 제37권6호
• /
• pp.433-441
• /
• 2021

The aim of this study was to optimize the ozonation and ceramic membrane integrated process for greywater reclamation. The integrated process is a repeated sequential process of filtration and backwash with the same ceramic membrane. Also, this study used ozone and oxygen gas for the backwashing process to compare backwashing efficiency. The study results revealed that the optimum filtration and backwash time for the process was 10 minutes each when comparing the filtrate flow and membrane recovery rate. The integrated process was operated at three different operating conditions with i) 10 minutes for filtration and 10 minutes for ozonation, ii) 10 minutes for filtration and 10 minute for oxygen aeration, and iii) continuous filtration without any aeration for synthetic greywater. The integrated process with ozone backwashing could produce 0.55 L/min of filtrate with an average of 18.42% permeability recovery, while the oxygen backwashing produced 0.47 L/min and 6.26%, respectively. And without any backwashing, the integrated process could produce 0.29 L/min. This shows that the ozone backwash process is capable of periodically recovering from membrane fouling. The resistance of the fouled membrane was approximately 34.4% for the process with ozone backwashing, whereas the resistance was restored by 10.8% for the process with oxygen backwashing. Despite the periodical ozone backwashing and chemical cleaning, irreversible fouling gradually increased approximately 3 to 4%. Approximately 97.6% and 15% turbidity and TOC were removed by ceramic membrane filtration, respectively. Therefore, the integrated process with ozonation and ceramic membrane filtration is a potential greywater treatment process.

• 산업경영시스템학회지
• /
• 제35권1호
• /
• pp.16-23
• /
• 2012

Recently, as organizational systems have become larger and more complicated, the evaluation for their efficiency and effectiveness has become more difficult but important. It is essential to understand the current strength and weakness of the organizational process. It can be a starting point for improving the efficiency and effectiveness of the organizational systems, because the quality of system outputs depend greatly on the capability of system process. Particularly in such process-based industries as semiconductor, energy or software industries, an assessment of process capability is more highlighted to gain knowledge of the expected quality and reliability of system outputs. As a result, much attention has been given to the issues of process capability assessment in the process-based industries. However, most of the previous research in those industries is based on case studies, a more generalized method for process capability assessment is in need for help more companies improve their processes. Therefore, this study aims to propose a process capability assessment method and apply the proposed method to an energy company. This research argues that the process capability is composed of individual and organizational capabilities of the process. Then, the concept of Capability Maturity Model Integration, which was initially suggested to evaluate the software development process, was introduced to develop the assessment tools and process. Finally, the proposed method was applied to a Korean company in the energy industry sector to verify its utility. The research outputs are expected to help more firms assess their process capability and ultimately improve the process.

• 한국미생물생명공학회:학술대회논문집
• /
• 한국미생물생명공학회 2003년도 2003 Annual Meeting, BioExhibition and International Symposium
• /
• pp.202-203
• /
• 2003

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2003년도 International Meeting on Information Display
• /
• pp.981-983
• /
• 2003

Using the conventional standard CMOS logic process, the high voltage MOSFET to drive top emission OLEDs was fabricated for the silicon-based organic electroluminescent display. The drift region of the conventional high voltage MOSFET was implemented by the n-well of the logic process. The measurement result shows a good saturation characteristic up to 50 V without breakdown phenomena.

• 한국미생물·생명공학회지
• /
• 제21권4호
• /
• pp.354-365
• /
• 1993

A novel control method with automatic tuning of PID controller parameters has been developed for efficient regulation of dissolved oxygen concentration in fed-batch fermentations of Escherichia coli. Agitation speed and oxygen partial pressure in the inlet gas stream were chosen to be the manipulated variables. A heuristic reasoning allowed improved tuning decisions from the supervision of control performance indices and it coule obviate the needs for process assumptions or disturbance patterns. The control input consisted of feedback and feedforword parts. The feedback part was determined by PID control and the feedforward part is determined from the feed rate. The proportional gain was updated on-line by a set of heuristics rules based on the supervision of three performance indices. These indices were output error covariance, the average value of output error, and input covariance, which were calculated on-line using a moving window. The integral and derivative time constants were determined from the period of output response. The specific growth rate was maintained at a low level to avoid acetic acid accumulation and thus to achieve a high cell density. The specific growthe rate was estimated from the carbon dioxide evolution rate. In fed-batch fermentation, the simutaneous control of dissolved oxygen concentration (at 0.2; fraction of saturated value) and specific growth rate (at 0.25$hr^{-1}$) was satisfactory for the entire culture period in spite of the changes in the feed rate and the switching of control input.

• 한국환경생물학회:학술대회논문집
• /
• 한국환경생물학회 2001년도 학술대회
• /
• pp.99-99
• /
• 2001

• 한국미생물생명공학회:학술대회논문집
• /
• 한국미생물생명공학회 2001년도 Proceedings of 2001 KSAM Annual Meeting
• /
• pp.17-18
• /
• 2001

• Ocean Systems Engineering
• /
• 제2권1호
• /
• pp.49-68
• /
• 2012

In this paper, an offshore process front end engineering design (FEED) method is systematically introduced and reviewed to enable efficient offshore oil and gas production plant engineering. An integrated process engineering environment is also presented for the topside systems of a liquefied natural gas floating production, storage, and offloading (LNG FPSO) unit, based on the concepts and procedures for the process FEED of general offshore production plants. Various activities of the general process FEED scheme are first summarized, and then the offshore process FEED method, which is applicable to all types of offshore oil and gas production plants, is presented. The integrated process engineering environment is presented according to the aforementioned FEED method. Finally, the offshore process FEED method is applied to the topside systems of an LNG FPSO in order to verify the validity and applicability of the FEED method.

• Biotechnology and Bioprocess Engineering:BBE
• /
• 제9권2호
• /
• pp.137-142
• /
• 2004

In this study, a simple procedure is described for patterning biotin on a glass substrate and then selectively immobilizing proteins of interest onto the biotin-patterned surface. Microcontact printing (CP) was used to generate the micropattern of biotin and to demonstrate the selective immobilization of proteins by using enhanced green fluorescent protein (EGFP) as a model protein, of which the C-terminus was fused to a core streptavidin (cSA) gene of Streptomyces avidinii. Confocal fluorescence microscopy was used to visualize the pattern of the immobilized protein (EGFP-cSA), and surface plasmon resonance was used to characterize biological activity of the immobilized EGFP-cSA. The results suggest that this strategy, which consists of a combination of $\mu$CP and cSA-fused proteins. is an effective way for fabricating biologically active substrates that are suitable for a wide variety of applications. one such being the use in protein-protein assays.