• Maxillofacial Plastic and Reconstructive Surgery
• /
• v.23 no.1
• /
• pp.87-94
• /
• 2001

The present study was performed to investigate the effect of $HTR^{(R)}$ (Hard Tissue Replacement) on osteogenesis in the mandibular bone defects. Eight adult male white rabbits weighing 2.5 to 3.0kg were used. Four bone defects (8mm in diameter and 4mm in depth) were made at the both mandibular body. In the control group, the right mesial bone defect was filled with blood clot and spontaneously healed. In the DFDB group, the right distal bone defect was filled with xenogenic demineralized freeze-dried bone. In the $HTR^{(R)}$ group, the left mesial bone defect was filled with $HTR^{(R)}$. In the $HTR^{(R)}-membrane$ group, the left distal bone defect was filled with $HTR^{(R)}$ and covered with BioMesh membrane. The rabbits were sacrified at 2,4,6 and 9 weeks after the operation and microscopic examination was performed. Results obtained were as follows: In the control and DFDB groups, inflammatory cells and the fibrous connective tissue existed and the bone growth was slower than $HTR^{(R)}$ group by 6 week, and there was intervention of the soft tissue at 9 week. In the $HTR^{(R)}$ group, bone trabeculi extended between the $HTR^{(R)}$ particles without intervention of inflammatory cells and the connective tissue at 4 and 6 weeks. In addition, extensive osseous ingrowth into the $HTR^{(R)}$ particles was observed at 9 week. Bone formation was more active in the $HTR^{(R)}$ group than the control and DFDB groups. There was not obvious difference in the bone healing rate between the $HTR^{(R)}$ and the $HTR^{(R)}-membrane$ group. These results suggest that the $HTR^{(R)}$ promotes osteogenesis in the bone defects and the $HTR^{(R)}$ group has no difference in comparison with the $HTR^{(R)}-BioMesh^{(R)}$ membrane group in bone healing.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2008.11a
• /
• pp.851-854
• /
• 2008

Using the recycled aggregate not only saves landfill space but also reduces the demand for extraction of natural raw material for new construction activity. However few investigations have been carried out to study the shear behaviors of RC beams with recycled aggregates such as low absorption of recycled aggregate and full-scale specimens. In this study, six reinforced concrete beams were tested to evaluate the effects of shear strength, and shear behavior on the replacement level (0, 30, 60, and 100%) of recycled coarse aggregate and different amounts of shear reinforcement. The results showed that the beams with recycled coarse aggregates present the similar shear strength and deflections as the beam with natural aggregate on an equal amount of shear reinforcement. the reinforced concrete beams with recycled coarse aggregates present the Influence of shear span-to-depth ratio, effective depth, tension reinforcement ratio and compressive strength as the beams with natural aggregate. Shear strength were compared with the provisions in current code (KCI2007) and the equation proposed by Zsutty. The KCI equations were conservative and subsequently can be used for the shear design of recycled aggregate concrete beam.

• Journal of Industrial Technology
• /
• v.26 no.B
• /
• pp.93-99
• /
• 2006

Centrifuge model experiments were performed to investigate the confining effects of the sheet piles, installed to the sides of soft clay ground treated with sand compaction piles, on the bearing capacity and concentration ratio of composite ground. For the given g-level in the centrifuge model tests, replacement ratio of SCP and the width of surcharge loads on the surface of ground with SCP, the confining effects of installing the sheet piles on the edges of SCP ground on the bearing capacity, change of stress concentration ratio and failure mechanism were investigated. Kaolin, one of typical clay mineral, and Jumunjin standard sand were used as a soft clay ground and sand compaction pile irrespectively. As results of experiments, lateral confining effect by inserting the model sheet piles fixed to the loading plate was observed. For the strip surcharge loading condition, the yielding stress intensity in the form of the strip surcharge loads tends to increase with increasing the embedded depth of sheet piles. The stress concentration ratio was found not to be influenced consistently with the embedded depth of sheet piles whereas the effect of stress intensity on stress concentration ratio shows the general trend that values of stress concentration ratio are relatively high at the initial stage of loading and tend to decrease and converge to the certain values. For the failure mechanism in the case of reinforced with sheet piles, displacement behavior related to the punching failure, settlement right beneath the loading plate occurred since the soil was confined with sheet piles, was observed.

• Steel and Composite Structures
• /
• v.45 no.3
• /
• pp.389-408
• /
• 2022

Residual capacity is defined as the load carrying capacity of an RC column after undergoing severe damage. Evaluation of residual capacity of RC columns is necessary to avoid damage initiation in RC structures. The central aspect of the current research is to propose an empirical formula to estimate the residual capacity of RC columns after undergoing severe damage. This formula facilitates decision making of whether a replacement or a repair of the damaged column is adequate for further use. Available literature mainly focused on the simulation of explosion loads by using simplified pressure time histories to develop residual capacity of RC columns and rarely simulated the actual explosive. Therefore, there is a gap in the literature concerning general relation between blast damage of columns with different explosive loading conditions for a reliable and quick evaluation of column behavior subjected to blast loading. In this paper, the Arbitrary Lagrangian Eulerian (ALE) technique is implemented to simulate high fidelity blast pressure propagations. LS-DYNA software is utilized to solve the finite element (FE) model. The FE model is validated against the practical blast tests, and outcomes are in good agreement with test results. Multivariate linear regression (MLR) method is utilized to derive an analytical formula. The analytical formula predicts the residual capacity of RC columns as functions of structural element parameters. Based on intensive numerical simulation data, it is found that column depth, longitudinal reinforcement ratio, concrete strength and column width have significant effects on the residual axial load carrying capacity of reinforced concrete column under blast loads. Increasing column depth and longitudinal reinforcement ratio that provides better confinement to concrete are very effective in the residual capacity of RC column subjected to blast loads. Data obtained with this study can broaden the knowledge of structural response to blast and improve FE models to simulate the blast performance of concrete structures.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.27 no.5
• /
• pp.16-22
• /
• 2023

In this study, a salt water immersion test was performed on concrete specimens simulating the concrete mix design of the nuclear power plant, and the correlation between the amount of chloride and the XRF component according to the depth of the concrete was analyzed. The amount of chloride on the surface of the nuclear power plant concrete increased slightly with increasing immersion time in salt water, but the amount of chloride in the depth of 5.5 mm or more showed a clear tendency to increase with increasing immersion time in salt water. As a result of analyzing the correlation between the amount of chloride in concrete and the XRF component, the concrete with 20% FA substitution compared with the OPC concrete showed a very high correlation between the composition ratio of Cl ions and the evaluation result of salt damage resistance by XRF component analysis. Accordingly, it was confirmed that chlorine ion analysis and salt damage resistance performance evaluation by XRF component analysis were possible through repeated data accumulation in the nuclear power plant concrete mix with 20% fly ash replacement.

• Economic and Environmental Geology
• /
• v.6 no.4
• /
• pp.195-200
• /
• 1973

Temperature environments of the formation of fluorite deposits in the Wolaksan area and the Cheonil Mine, Chungcheongbuk-Do are presented and interpreted in brief. These deposits occur more or less near the contact zone between the Paleozoic limestone formations and the Cretaceous biotite granites as a number of hydrothermal veins or replacement deposits. The homogenization temperatures of fluorite crystals from the Wolaksan area fall within the narrow range of $149{\sim}167^{\circ}C$, of which lower limit is quite high, while those of the Cheonil Mine show wide range of $126{\sim}177^{\circ}C$, which indicates much lower mean temperature of formation. If the possible correction for pressure, which may not exceed $+30^{\circ}C$ as the depth of the deposits was 1.5km, were applied, the possible highest value of the true formation temperatures of fluorites in both area might be reached to around $200^{\circ}C$ that means these deposits were formed as a series of early products of the epithermal stage of hydrothermal processes.

• Transactions of Materials Processing
• /
• v.24 no.4
• /
• pp.264-271
• /
• 2015

In the current study, a method was proposed to quantitatively predict the wear and fatigue life of a shearing die in order to determine an effective replacement period for the die. The shearing die model of a retainer manufacturing process was used for the proposed method of quantitative life prediction. The retainer is produced through shearing steps, such as piercing and notching. The shearing die of the retainer is carefully controlled because the dimensional accuracy of the retainer is critical. The fatigue life for the shearing die was predicted using ANSYS considering S-N curves of STD11 and Gerber’s equation. The wear life for the shearing die was predicted using DEFORM-3D considering the Archard’s wear model. Experimental shearing of the retainer was conducted to verify the effectiveness of the proposed method for predicting die life. The fatigue failure of the shearing die was macroscopically measured. The wear depth was measured using a 3D coordinate measuring machine. The results showed that the wear and fatigue life in the FE analysis agree well with the experimental results.

• Magazine of the Korea Concrete Institute
• /
• v.10 no.6
• /
• pp.161-168
• /
• 1998

Increase of traffic volume in recent years results in deterioration of the bridge slab, which is directly subjected ot vehicle loads. Where extensive repair is necessary, replacement or enhancement of load carrying capacity using full depth precast concrete deck is often the most practical solution. Precast deck system has transverse joints between adjacent precast decks. Vertical shear forces occur when a vehicle wheel load is carried by precast decks and the joints are used to transfer the load to an adjacent deck. Effective load transfer between precast decks is critical for integral behavior. Finite element analysis and tests were run on the proposed femal-to-female type joint. 18 joint specimens were tested to investigate the effects of angle. D/H, and confining stress under static load. Results indicate joint with angle of 60$^{\circ}$ and D/H of 1/4 shows the improved load carrying capacity on crack. It is effective in protecting the cracking of joints to keep the joint in compression using confining stress.

• Steel and Composite Structures
• /
• v.12 no.5
• /
• pp.379-393
• /
• 2012

Many steel bridge infrastructures in the world are getting older, and a large number of these structures are in need of maintenance, rehabilitation or replacement. Most of them are subjected to corrosion due to exposure to aggressive environmental conditions and inadequate maintenance, causing reduction of their carrying capacities. In order to have an adequate bridge management, it is of paramount importance to develop an efficient, accurate and rapid condition assessment method which can be used to make reliable decisions affecting the cost and safety. Therefore, a simple and accurate method of calculating remaining yield and tensile strength by using a concept of representative effective thickness with correlation of initial thickness and maximum corroded depth is proposed in this study, based on the results of many tensile coupon tests of corroded plates obtained from a steel plate girder with severe corrosion, used for about 100 years. Furthermore, a strength reduction diagram which will be very useful for bridge inspection engineers to make rational decisions about the maintenance management of aged steel bridge infrastructures is presented.

• Steel and Composite Structures
• /
• v.24 no.1
• /
• pp.113-128
• /
• 2017

This paper highlights a study undertaken on the free vibration of a precast steel-concrete composite slab panel for track support. The steel-concrete composite slab track is an evolvement from the slab track, a form of ballastless track which is becoming increasingly attractive to asset owners as they seek to reduce lifecycle costs and deal with increasing rail traffic speeds. The slender nature of the slab panel due to its reduced depth of construction makes it susceptible to vibration problems. The aim of the study is driven by the need to address the limited research available to date on the dynamic behaviour of steel-concrete composite slab panels for track support. Free vibration analysis of the track slab has been carried out using ABAQUS. Both eigenfrequencies and eigenmodes have been extracted using the Lanczos method. The fundamental natural frequencies of the slab panel have been identified together with corresponding mode shapes. To investigate the sensitivity of the natural frequencies and mode shapes, parametric studies have been established, considering concrete strength and mass and steel's modulus of elasticity. This study is the world first to observe crossover phenomena that result in the inversion of the natural orders without interaction. It also reveals that replacement of the steel with aluminium or carbon fibre sheeting can only marginally reduce the natural frequencies of the slab panel.