• Journal of the Korea Concrete Institute
• /
• 제15권3호
• /
• pp.462-469
• /
• 2003

This paper presents an experimental study on the potential durability enhancement of infrastructures repaired by a sprayed high ductile fiber-reinforced cementitious composite (ECC). For this study, a PVA-ECC which exhibits sprayable properties in the fresh state and tensile strain-hardening behavior in hardened state was sprayed and tested. The experimental results show that the sprayed ECC exhibits mechanical properties with strain capacity comparable to the cast ECC with the same mix design. During loading, the crack widths of ECC are tightly controlled with an average of 30${\mu}m$. It is also revealed that when sprayed ECC is used as a repair material, ductility represented by deformation capacity at peak load of repaired beams in flexure are obviously increased in comparison to those of commercial prepackaged mortar (PM) repaired beams. In addition to high delamination resistance, the significant enhancement of energy absorption capacity and crack width control in ECC repair system suggest that sprayed ECC can be effective in extending the service life of rehabilitated infrastructures.

• Journal of the Korea institute for structural maintenance and inspection
• /
• 제24권1호
• /
• pp.59-66
• /
• 2020

In this study, self - healing solid capsules of crystal growth type which can be mixed directly with repair mortar were prepared, and the quality and crack healing performance of repair mortar with self - healing solid capsules were evaluated. The table flow and the air flow rate of the repair mortar material mixed with self-healing solid capsules were found to have no significant influence on table flow and air volume regardless of mixing ratio. Compressive strength tended to decrease with increasing capsule mixing ratio. As a result of evaluation of crack healing properties according to constant water head permeability test, initial water permeability decreased, and reaction products were generated over time and cracks were healed.

• Journal of the Korea Institute of Building Construction
• /
• 제19권4호
• /
• pp.299-306
• /
• 2019

In general, repair mortar is used to rehabilitate underground communities, but difficulties are encountered in the execution of long-term construction due to spatial co-operatives. In this study, the engineering properties of repair mortar according to the curing condition and accelerator type were reviewed. The results showed that the aluminate, alkali-free and calcium-aluminate precipitates in the water curing conditions showed higher compressive strength at the beginning of age than mortar specimens under air curing conditions, and increased. Especially in CA and AF test specimen with cement mineral quick setting, a large amount of ettringite products were observed compared with AL, thus reducing the pore volume and increasing the strength of the compound by micro-filling effect were found.

• Journal of the Architectural Institute of Korea Structure & Construction
• /
• 제34권9호
• /
• pp.19-26
• /
• 2018

The focus of this study was centered around 15 common injection type water leakage repair materials (3 different types for each; synthetic polymer, cementitious, acrylic, epoxy, urethane) used in concrete structures of Korea and analyzing their wet surface adhesion performance in accordance to the ISO TS 16774 Test Method for Repair Materials for Water-leakage Cracks in Underground Concrete Structures, Part 4: Test Method for Adhesion on Wet Concrete Surface, and the results of this study was taken to be place under a comparative analysis with the results of the preceeding study on response to substrate movement performance study. The results of this comparative study showed that other than 1 specimen of 1 type of the acrylic and 3 specimens of 1 type of the synthetic polymer type materials, all of the 93% of the specimens used in this study showed stable adhesion on wet substrate surface, and we were able to determine that materials that have proper response properties against substrate movement are highly flexible and have high adhesion properties, but their adhesion properties on wet substrate would change based on their viscosity.

• Journal of the Korean Recycled Construction Resources Institute
• /
• 제5권4호
• /
• pp.395-402
• /
• 2017

Recently, many researches on crack healing and repairing technique using bacteria which can produce vital-reacted calcite have been proposed. This study is for a basic research on repair material with slime formation through bacteria and deals with durability evaluation for coating materials containing bacteria-forming slime. For the work, 4 types of bacteria (Rhodobacter capsulatus, Rhodopseudomonas palustris, Bacillus thuringiensis, and Bacillus subtilis) and 2 types of nutrient conditions are considered, and several tests covering strength evaluation under sulfate condition, accelerated chloride diffusion, and UV (Ultrasonic Velocity) measurement are performed. Strength improvement in coating materials containing bacteria is evaluated in spite of even exposure to sulfate attack to 7 days. Chloride diffusion coefficient and UV properties are also improved except for the case of Rhodopseudomonas palustris. With resistance of slime to long term exposure and aerobic conditions for bacteria longevity, the proposed bacteria shows an engineering feasibility for repair material of RC structure exposed harsh environment.

• The Journal of Advanced Prosthodontics
• /
• 제12권5호
• /
• pp.273-282
• /
• 2020

PURPOSE. To assess shear bond strengths (SBS) of resin composites on aged and non-aged prosthetic materials with various surface treatments. MATERIALS AND METHODS. Cerasmart (CE), Vita Enamic (VE), Vita Mark II (VM), and IPS e.max CAD (EC) blocks were sliced, and rectangular-shaped specimens (14 × 12 × 1.5 mm; N = 352) were obtained. Half of the specimens were aged (5000 thermal cycles) for each material. Non-aged and aged specimens were divided into 4 groups according to the surface treatments (control, air abrasion, etching, and laser irradiation; n = 11) and processed for scanning electron microscopy (SEM). The repair procedure was performed after the surface treatments. SBS values and failure types were determined. Obtained data were statistically analyzed (P≤.05). RESULTS. The material type, surface treatment type, and their interactions were found significant with regard to SBS (P<.001). Aging also had a significant effect on prosthetic material-resin composite bonding (P<.001). SBS values of non-aged specimens ranged from 12.16 to 17.91 MPa, while SBS values of aged specimens ranged from 9.46 to 15.61 MPa. Non-aged VM in combination with acid etching presented the highest score while the control group of aged CE showed the lowest. CONCLUSION. Etching was more effective in achieving durable SBS for VM and EC. Laser irradiation could be considered as an alternative surface treatment method to air abrasion for all tested materials. Aging had significant effect on SBS values generated between tested materials and resin composite.

• Journal of the Korean Association of Oral and Maxillofacial Surgeons
• /
• 제33권5호
• /
• pp.464-469
• /
• 2007

The bone graft materials are grossly divided into autogenous bone, allogenic bone, xenogenic bone, and alloplastic material. Among the various allogenic graft materials, hydroxyapatite($Ca_{10}(PO_4)_6(OH)_2$, HA), the main inorganic phase of human hard tissue, is widely used as a repair material for bones. When HA applied to bony defect, however, it may be encapsulated with fibrous tissue and floated in the implanted area by the lack of consolidation. Fluoridated hydroxyapatite($Ca_{10}(PO_4)_6(OH)_2$, FHA), where F- partially replaces the OH- in the hydroxyapatite, is considered as an alternative material for bone repair due to its solubility and biocompatibility. This study was designed to find out the bone healing capacity of FHA newly produced as a nanoscale fiber in the laboratory. We implanted HA and FHA in the rabbit cranium defect and histologically analysed the specimen. The results were as follows. 1. In the 4 weeks, fibrous connective tissue and little bone formation around materials of the experimental group I implanted HA were observed. In the experimental group II implanted FHA, newly formed bone around materials were observed. 2. In the 8 weeks, the amount of newly formed and matured bone of the experimental group II was more than the experimental group I and control group. From the results obtained, we suggest that FHA, newly synthesized, is relatively favorable bone substitute with bioconpatibility and has better bone healing capacity than pure HA.

• Journal of Korean Neurosurgical Society
• /
• 제64권5호
• /
• pp.799-807
• /
• 2021

Objective : Cerebrospinal fluid leakage related complications (CLC) occasionally occur after intradural spinal surgery. We sought to investigate the effectiveness of early ambulation after intradural spinal surgery and analyze the risk factors for CLC. Methods : For this retrospective cohort study, we enrolled 314 patients who underwent intradural spinal surgery at a single institution. The early group contained 79 patients who started ambulation after 1 day of bedrest without position restrictions, while the late group consisted of 235 patients who started ambulation after at least 3 days of bed rest and were limited to the prone position after surgery. In the early group, Prolene 6-0 was used as the dura suture material, while black silk 5-0 was used as the dura suture material in the late group. Results : The overall incidence rate of CLC was 10.8%. Significant differences between the early and late groups were identified in the rate of CLC (2.5% vs. 13.6%), surgical repair required (1.3% vs. 7.7%), and length of hospital stay (2.99 vs. 9.29 days) (p<0.05). Logistic regression analysis revealed that CLC was associated with practices specific to the late group (p=0.011) and the revision surgery (p=0.022). Conclusion : Using Prolene 6-0 as a dura suture material for intradural spinal surgery resulted in lower CLC rates compared to black silk 5-0 sutures despite a shorter bed rest period. Our findings revealed that suture - needle ratio related to dura defect was the most critical factor for CLC. One-day ambulation after primary dura closure using Prolene 6-0 sutures appears to be a costeffective and safe strategy for intradural spinal surgery.

• Restorative Dentistry and Endodontics
• /
• 제46권4호
• /
• pp.53.1-53.11
• /
• 2021

Objectives: This study evaluates the bond strength and marginal adaptation of mineral trioxide aggregate (MTA) Repair HP and Biodentine used as apical plugs; MTA was used as reference material for comparison. Materials and Methods: A total of 30 single-rooted teeth with standardized, artificially created open apices were randomly divided into 3 groups (n = 10 per group), according to the material used to form 6-mm-thick apical plugs: group 1 (MTA Repair HP); group 2 (Biodentine); and group 3 (white MTA). Subsequently, the specimens were transversely sectioned to obtain 2 (cervical and apical) 2.5-mm-thick slices per root. Epoxy resin replicas were observed under a scanning electron microscope to measure the gap size at the material/dentin interface (the largest and smaller gaps were recorded for each replica). The bond strength of the investigated materials to dentin was determined using the push-out test. The variable bond strengths and gap sizes were evaluated independently at the apical and cervical root dentin slices. Data were analyzed using descriptive and analytic statistics. Results: The comparison between the groups regarding the variables' bond strengths and gap sizes showed no statistical difference (p > 0.05) except for a single difference in the smallest gap at the cervical root dentin slice, which was higher in group 3 than in group 1 (p < 0.05). Conclusions: The bond strength and marginal adaptation to root canal walls of MTA HP and Biodentine cement were comparable to white MTA.

• Proceedings of the Korea Concrete Institute Conference
• /
• 한국콘크리트학회 2001년도 가을 학술발표회 논문집
• /
• pp.497-502
• /
• 2001

We examined the silicate-based material to develop the surface-treatment agent, which would be used to restore performance of the deteriorated concrete and to inhibit corrosion of the reinforcing bar. As a part of the study, we carried out experiments of the penetration and strengthening properties of concrete treated by the considering agent. The variables of experiment, were the type of silicates, the ratio of distilled water-silicate, the usage of surface-strengthening material, and the usage of biochemical material. The penetrating ability of concrete is assessed by viscosity and surface tension. Also assessments of strengthening effects of concrete are performed on compressive strength, absorption, and water permeability tests.