• 대한물리치료과학회지
• /
• 제4권1호
• /
• pp.255-263
• /
• 1997

The purpose of this study was to examed the pain relief effects of myofascial pain syndrome patient by post-isometric relaxation. From July, 1996 to January, 1997, PIR was applied to myofascial pain syndrome associated with musculoskelatal lesions and was examed on 17 muscles in 98 patients at Sun General Hospital, Taejon city. The results of this study were as follows ; 1. Immediate pain relief group was 58(59%). 2. Only tenderness relief group was 24(25%). 3. No effect group was 16(16%). These results could be confirmed that the increased tension of the affected muscles with the resulting pain relieved by restoring the full stretch length of the muscle by PIR.

• 한국지형학회지
• /
• 제23권1호
• /
• pp.1-16
• /
• 2016

This study estimates relationships between physical and chemical weathering indices of various rock types and topographical relief. Physical weathering properties such as rock strength and joint and chemical weathering indices such as the $SiO_2/Al2O_3$, CIA and WPI were analyzed from 18 rock outcrops in mountain and valley areas consisting of 9 rock types. The results indicate that the elevation and relief of topography increase physical strength of rock increases. It can be suggested that the total r(rock-mass strength rating) and R(rock rebound strength by Schmidt Hammer) are most useful indices as a quantitative weathering property factor to explain formative causes of topographical relief. The results also suggest that rock types such as sandstone, granite, gneiss and schist are most suitable to explain meaningful difference in topographical relief with the physical and chemical weathering indices.

• 드라이브 ㆍ 컨트롤
• /
• 제15권4호
• /
• pp.61-66
• /
• 2018

Almost every hydraulic system is equipped with a pressure relief valve, to maintain working pressure of the system at a pre-determined level. Thus, dynamic characteristics of such a relief valve, in conjunction with other hydraulic components, are important in designing the hydraulic control system. The single stage pressure relief valve is dynamically undesirable, due to relatively low viscous damping, that causes high frequency oscillations. This problem is overcome by introducing orifices in the inner pilot line, and drain line. In this study, for the single stage spool type pressure relief valve, the system equations were derived through an adequate linearisation and several simplifications were made, to use the transfer function formulation technique. All coefficients were evaluated and used, to make some results by using Matlab software. Results of analysis are compared with experimental results. In this study, parameters affecting stability of valve design are determined and suggested relative to the design.

• 한국유체기계학회 논문집
• /
• 제12권1호
• /
• pp.16-21
• /
• 2009

In the last five years, 91 accidents from portable gas ranges and non-refillable metallic gas cartridges have occurred. The gas cylinder installed with a relief valve was developed to prevent an explosive accident from the gas cartridge. In this study it was carried out to evaluate the safety of a gas cylinder mounted with a relief valve which can prevent an explosion. Under the real using condition and the extreme condition the gas cylinder is heated with an electric heater. Simultaneously, the operating pressure is checked and the suitability of releasing flux is evaluated. And the possibility of fire or explosion was tested when the gas was released from the relief valve at the real using condition. Using a numerical simulation method, the diffusion of butane gas released from a relief valve was visualized.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2011년도 제37회 추계학술대회논문집
• /
• pp.854-856
• /
• 2011

우주발사체의 액체 추진제 공급 시스템에 사용되는 산화제 탱크용 벤트릴리프밸브를 설계하였다. 벤트릴리프밸브는 충전 중 산화제 탱크의 배기를 담당하고 충전 후 과압이 걸리지 않도록 보호하는 역할을 한다. 충전 중 탱크 배기는 벤트밸브에서 담당하며 탱크의 보호는 릴리프밸브와 벤트밸브의 연계 작동을 통하여 이루어진다. 수치해석을 통하여 공압 성능 및 동특성이 밸브 요구조건을 만족하는 것을 확인하였다. 시제품을 제작한 후 벤트릴리프밸브의 성능을 평가하기 위한 시험을 수행하고 있다.

• 한국기계가공학회지
• /
• 제11권1호
• /
• pp.88-94
• /
• 2012

An axle drive shaft with double joint shaft, cross kit and yoke has an important role by transferring power and changing steering angle between axle and wheel in power train system. It has been used widely in the heavy machinery requiring a high reliability in the power train system. At fatigue failures of the axle drive shaft with the long span, a relatively high stress concentration at a snap ring groove on the drive shaft brings to significant fatigue damages under repeated loading condition. As Peterson's suggestions on this study, a relief groove in the vicinity of the snap ring groove is applied by decreasing the stress concentration and improving the fatigue life of axle drive shaft. By using FEM analysis, the decreasing effect of the stress concentration and extended fatigue life are due to the change of design parameters related with size and location of the relief groove. The relief groove with the design parameters such as d/b=2.0 and r/h=1.2 enables to decrease the stress concentration of 22.3% and increase the fatigue life more than 3 times by comparing with no relief groove application.

• 한국생산제조학회지
• /
• 제25권3호
• /
• pp.171-176
• /
• 2016

Growing concerns about air pollution have led to increased demand for liquefied natural gas (LNG)-fuelled ships that have crankcases equipped with explosion relief valves to relieve excessive crankcase pressures and stop the flames emitted from the crankcase. The results of a computational fluid dynamics (CFD)-based feasibility analysis of the crankcase relief valve flame arrester design conducted using ANSYS CFX V14 showed that the inlet and outlet relief valve temperatures differed by $350-700^{\circ}C$. An explosion test was performed based on European standard EN14797 to evaluate the flame transmission and mechanical integrity of the valve. No flame transmission from the pressure vessel to the exterior was detected, and the mechanical integrity of the valve was confirmed. Thus, the relief valve components were found to be safe from the viewpoint of fracture.

• 대한물리의학회지
• /
• 제11권4호
• /
• pp.49-54
• /
• 2016

PURPOSE: The purpose of this study was to determine the effect of different frequencies (4Hz and 100Hz) of transcutaneous electrical nerve simulation (TENS) on pain relief using c-fos expression in the spinal cord of rat osteoarthritis to investigate the appropriate frequency for pain relief. METHODS: Total of 30 Sprague-Dawley rats was used and randomly divided 2 groups according TENS frequency and applicate the TENS during 3 period (3 days, 7 days, 10 days). The induction of osteoarthritis by 3mg monosodium iodoacetat was injected into the right knee joint of rats. Three days later, commercially available TENS unit was used for stimulation was set to 20minutes on 3, 7, 10 days after surgery. Western blot analysis system was used to detect immunoreactive proteins. The thickness of the bands were photographically measured by Scion Image. RESULTS: When investigating the c-fos expression of TENS on spinal cord in OA knee over 10 days, between-groups differences in c-fos expression reached a significant level by day 10. For within-groups comparisons, the c-fos expression decreased significantly across days in low- and high-frequency TENS groups. CONCLUSION: Whether at low- and high-frequency, the TENS as a therapy obtained beneficial effects of pain relief and TNES at high-frequency is more beneficial effects on the pain relief when TENS applied at injury site.

• 한국유체기계학회 논문집
• /
• 제8권3호
• /
• pp.16-25
• /
• 2005

The purpose of this study is localization of safety relief valves for Nuclear Service. The safety relief valve is the important equipment used to protect the pressure vessel, the steam generator and the other pressure facility from overpressure by discharging the operating medium when the pressure of system is reaching the design pressure of the system. We developed design technology used FEM ' CFM about safety relief valve for Nuclear Service according to ASME (or KEPIC) Code and KHNP's Technical Specification. To prove validity of a design technology, actually, we manufactured and inspected and tested the sample products designed according to a developed technology. The capacity qualification test was achieved according to requirement of ASME(or KEPIC) Code by NBBI and the functional qualification test was achieved according to ASME QME-1 for operating condition in technical specification of KHNP by NLI. Therefore we have to achieve the development of safety relief valves for Nuclear Service with our own technologies.

• 항공우주산업기술동향
• /
• 제9권1호
• /
• pp.130-138
• /
• 2011

벤트릴리프 밸브는 추진제 탱크의 충전 중 내부의 기체를 배출시키고 충전이 완료된 후에는 탱크의 과압을 해소하는 안전밸브의 역할을 수행한다. 신뢰성과 비용 절감 차원에서 모든 미국의 극저온 액체 추진제를 사용하는 발사체에서는 거의 유사한 벤트릴리프 밸브를 적용해오고 있다. 그리고 발사체의 다양한 임무요구조건을 만족하기 위하여 밸브를 다소 수정하여 사용해오고 있다. 본 논문에서는 발사체 추진제 공급 시스템에 적용되는 벤트릴리프 밸브의 설계 및 제작과 관련한 핵심 기술 동향을 살펴본다. 그리고 우주개발 선진국 발사체에 사용된 벤트릴리프밸브의 운용기술을 소개한다.