• 한국운동역학회지
• /
• 제17권3호
• /
• pp.197-207
• /
• 2007

It has been reported that Back-Tension played a significant role in archery (Lee & Bondit, 2005; Kim, 2007) but there are a few researches related Back-Tension in Korea recently. Therefore, the purpose of this study was to investigate archery back tension technique for the second ranked archer in the World and to find ways to improve performance. A subject(height: 185cm, mass: 82kg, years: 21yrs, careers: 12yrs) who is a number of national team and the second ranked archer in the World authorized by FITA (Federation Internationale de Trial Arc) was perticipated in this experiment. When shooting 60 shots($12{\times}5$), shooting motions were recorded with 7 infrared cameras and 2 ultrahigh-speed cameras. A QTM and an Auto Track were used to acquire raw data. The sampling rates of both cameras were 200 Hz. and 1000 Hz. respectively and data were filtered using a fourth order Butterworth low pass filtering with a cutoff-frequency of 30Hz. The parameters were calculated with Matlab6.5 and analyzed with SPSS11.0. After Pearson's correlations between 8 parameters were analyzed, 5 parameters from 13parameters that affected records were analyzed with multiple regression analysis (Enter order: x1, x2, x3, x4, x5). The results were as follows: 1. Comparing between parameters according to scores, the patterns of horizontal and vertical angular velocity(av.) of scapular relative angle was different between 8 score and 9 or 10 scores. 2. The correlations of parameters that affected records were a horizontal av.(x1, p=.032<.05) and a vertical av.(x3, p=.033<.05) of scapular from release to delivery in KB back-tension (anchoring-delivery). 3. The decision coefficients(R2) of above two parameters and three parameters selected by experts that may affect record, that is, an absolute trunk angle(x4) from in KKC back-tension (anchoring-release) and a horizontal relative scapular angle(x2) and an absolute trunk angle(x5) from release to delivery in KB back-tension were 7.7%(x1), 0.1%(x2), 8.5%(x3), 0.7%(x4) and 0.9%(x5) in sequence. 4. The multiple regression equation was a y= -1.16E-2 x1 + 0.109 x2 + 3.437E-2 x3 + 6.139E-2 x4 + 0.117 x5 + 3.420 In conclusion, a total contribution was low, that is, R2(17.9%) suggested that on the one hand, Lim's motion may not depend on a certain factor because his postural factors affected shooting motion are some stable on the other hand, unknown factors may exist(e.g. psychological, physiological factors etc.). Further study of EMG patterns of muscles and anatomic consideration related to shoulder girdle and scapular bones may help to identify mechanism of Back-Tension.

• Tribology and Lubricants
• /
• 제32권2호
• /
• pp.39-43
• /
• 2016

Magnetorheological elastomers (MREs) are a type of “smart” material, and their properties can be controlled rapidly and reversibly under the influence of an external stimulus. The application of an external magnetic field can change the shear modulus, hardness, and friction coefficient of MREs. The friction can cause vibration; moreover, the vibration can affect friction. The change of friction depends on the relative motion, normal force, roughness of the rubbing surfaces, material type, temperature, lubrication, relative humidity, and vibration condition. As MREs are a type of “smart material,” their friction coefficient can be reduced by applying an external magnetic field—the applications of this feature in engineering have been widely studied. However, the friction properties of MREs under vibration have not been tested to date. In this study, MRE samples and a reciprocating friction tester were fabricated. The friction coefficient was measured to evaluate the friction properties under various vibration conditions; subsequently, the wear depth and wear surface profile of the MRE were observed in order to evaluate the wear properties. The results show that the friction coefficient of the MREs decreased when a magnetic field was applied. Moreover, the friction coefficient decreased when the vibrational amplitudes increased. The wear depth of the MRE also decreased as the vibrational amplitudes increased.

• Steel and Composite Structures
• /
• 제15권4호
• /
• pp.379-397
• /
• 2013

Conoidal shells are doubly curved stiff surfaces which are easy to cast and fabricate due to their singly ruled property. Application of laminated composites in fabrication of conoidal shells reduces gravity forces and mass induced forces compared to the isotropic constructions due to the high strength to weight ratio of the material. These light weight shells are preferred in the industry to cover large column free open spaces. To ensure design reliability under service conditions, detailed knowledge about different behavioral aspects of conoidal shell is necessary. Hence, in this paper, static bending, free and forced vibration responses of composite conoidal shells are studied. Lagrange's equation of motion is used in conjunction with Hamilton's principle to derive governing equations of the shell. A finite element code using eight noded curved quadratic isoparametric elements is developed to get the solutions. Uniformly distributed load for static bending analysis and three different load time histories for solution of forced vibration problems are considered. Eight different stacking sequences of graphite-epoxy composite and two different boundary conditions are taken up in the present study. The study shows that relative performances of different shell combinations in terms of static behaviour cannot provide an idea about how they will relatively behave under dynamic loads and also the fact that the points of occurrence of maximum static and dynamic displacement may not be same on a shell surface.

• International Journal of Aeronautical and Space Sciences
• /
• 제12권1호
• /
• pp.43-56
• /
• 2011

An integrated system composed of guidance, navigation and control (GNC) system for autonomous proximity operations and the docking of two spacecraft was developed. The position maneuvers were determined through the integration of the state-dependent Riccati equation formulated from nonlinear relative motion dynamics and relative navigation using rendezvous laser vision (Lidar) and a vision sensor system. In the vision sensor system, a switch between sensors was made along the approach phase in order to provide continuously effective navigation. As an extension of the rendezvous laser vision system, an automated terminal guidance scheme based on the Clohessy-Wiltshire state transition matrix was used to formulate a "V-bar hopping approach" reference trajectory. A proximity operations strategy was then adapted from the approach strategy used with the automated transfer vehicle. The attitude maneuvers, determined from a linear quadratic Gaussian-type control including quaternion based attitude estimation using star trackers or a vision sensor system, provided precise attitude control and robustness under uncertainties in the moments of inertia and external disturbances. These functions were then integrated into an autonomous GNC system that can perform proximity operations and meet all conditions for successful docking. A six-degree of freedom simulation was used to demonstrate the effectiveness of the integrated system.

• Ocean Systems Engineering
• /
• 제3권3호
• /
• pp.203-217
• /
• 2013

A PTO (power-take-off) mechanism by using relative heave motions between a floating buoy and its inner mass (magnet or amateur) is suggested. The inner power take-off system is characterized by a mass with linear stiffness and damping. A vertical truncated cylinder is selected as a buoy and a special station-keeping system is proposed to minimize pitch motions while not affecting heave motions. By numerical examples, it is seen that the maximum power can actually be obtained at the optimal spring and damper condition, as predicted by the developed WEC(wave energy converter) theory. Then, based on the developed theory, several design strategies are proposed to further enhance the maximum PTO, which includes the intentional mismatching among heave natural frequency of the buoy, natural frequency of the inner dynamic system, and peak frequency of input wave spectrum. By using the intentional mismatching strategy, the generated power is actually increased and the required damping value is significantly reduced, which is a big advantage in designing the proposed WEC with practical inner LEG (linear electric generator) system.

• Journal of Mechanical Science and Technology
• /
• 제15권8호
• /
• pp.1097-1107
• /
• 2001

In this paper, the wall following navigation algorithm of the mobile robot using a mono vision system is described. The key points of the mobile robot navigation system are effective acquisition of the environmental information and fast recognition of the robot position. Also, from this information, the mobile robot should be appropriately controlled to follow a desired path. For the recognition of the relative position and orientation of the robot to the wall, the features of the corridor structure are extracted using the mono vision system, then the relative position, the offset distance and steering angle of the robot from the wall, is derived for a simple corridor geometry. For the alleviation of the computation burden of the image processing, the Kalman filter is used to reduce search region in the image space for line detection. Next, the robot is controlled by this information to follow the desired path. The wall following control scheme by the PD control scheme is composed of two control parts, the approaching control and the orientation control, and each control is performed by steering and forward-driving motion of the robot. To verify the effectiveness of the proposed algorithm, the real time navigation experiments are performed. Through the result of the experiments, the effectiveness and flexibility of the suggested algorithm are verified in comparison with a pure encoder-guided mobile robot navigation system.

• 제어로봇시스템학회논문지
• /
• 제22권7호
• /
• pp.562-569
• /
• 2016

This paper proposes a navigation system with a robust localization method for an underwater unmanned vehicle. For robust localization with IMU (Inertial Measurement Unit), a DVL (Doppler Velocity Log), and depth sensors, the EKF (Extended Kalman Filter) has been utilized to fuse multiple nonlinear data. Note that the GPS (Global Positioning System), which can obtain the absolute coordinates of the vehicle, cannot be used in the water. Additionally, the DVL has been used for measuring the relative velocity of the underwater vehicle. The DVL sensor measures the velocity of an object by using Doppler effects, which cause sound frequency changes from the relative velocity between a sound source and an observer. When the vehicle is moving, the motion trajectory to a target position can be recorded by the sensors attached to the vehicle. The performance of the proposed navigation system has been verified through real experiments in which an underwater unmanned vehicle reached a target position by using an IMU as a primary sensor and a DVL as the secondary sensor.

• 한국철도학회논문집
• /
• 제5권4호
• /
• pp.260-266
• /
• 2002

A numerical simulation has been performed to estimate the transient pressure variation in the tunnel when G7 test train passes through the test tunnel in the Kyoeng-Bu high-speed railway. A modified patched grid scheme is developed to handle the relative motion between a train and a tunnel. Also, a hybrid dimensional approach is proposed to calculate the train-tunnel interaction problem efficiently. An axi-symmetric unsteady Euler solve using the Roe's FDS is used for analyzing a complicated pressure field in tunnel during the test train is passing through the tunnel. Usually, this complex phenomenon depends ell the train speed, train length, tunnel length, blockage ratio between train and tunnel cross-sectional area, relative position between train and tunnel, etc. Therefore, numerical simulation should be done carefully in consideration of these factors. Numerical results in this study would be good guidance to make test plans, test equipments selection and to decide their measuring locations. They will also supply important information to the pressurization equipment for high-speed train.

• 한국산업보건학회지
• /
• 제8권1호
• /
• pp.36-49
• /
• 1998

The purpose of this study is to investigate the relationship between the work postures and upper extremity cumulative trauma disorders(CTDs) in female medical insurance bill reviewers(n=448). This study included diagnosis for CTDs, anthropometry and job analysis (workstations and posture). The characteristics of subject were 33.6 years of average age and 8.7 years of average work duration. The results were as fallows. Ergonomic conditions of workstation were unsuitable compared with anthropometry result. The height of work surface(79.5 cm) and chair(43.0 cm)were high. work space was small, and legs space under the table was limited. Work postures were awkward compared with recommended neutral postures. Neck flexion($21.0-36.0^{\circ}$), elbow elevation, shoulder abduction ($46.0-47.0^{\circ}$). wrist radial and ulnar deviation, forearm supination and pronation, and wrist repeated motion(12.7-21.5 freq./min) were analyzed as hazardous risk factors by job analysis. The prevalence of CTDs was 32.8 % by medical diagnosis. The prevalence rate of CTDs in hazardous work posture group was significantly greater than safe work posture group both neck-shoulder (relative prevalence = 5.2, p<0.001) and wrist-hand (relative prevalence = 2.5, p<0.05).

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2008년도 추계학술대회A
• /
• pp.622-624
• /
• 2008

This investigation studies the effects of material properties and corresponding propagation wave types on optimal configurations of sound absorbing porous materials in maximizing the absorption performance by topology optimization. The acoustic behavior of porous materials is characterized by their material properties which determine motions of the frame and the air. When the frame has a motion, two types of compressional wave propagate in the porous material. Because each wave in the material make different influence on the absorption performance, it is important to understand the relative contribution of each wave to the sound absorption. The relative contribution of the propagating waves in a porous material is determined by the material properties, therefore, an optimal configuration of a porous material to maximize the absorption performance is apparently affected by the material properties. In fact, virtually different optimal configurations were obtained for absorption coefficient maximization when the topology optimization method developed by the authors was applied to porous materials having different material properties. In this investigation, some preliminary results to explain the findings are presented. Although several factors should be considered, the present investigation is focused on the effects of the material properties and corresponding propagation waves on the optimized configurations.