• Structural Engineering and Mechanics
• /
• v.26 no.4
• /
• pp.409-426
• /
• 2007

Following previous work carried out in Building Research Institute in Japan, finite element analyses of conceptual column designs are performed in this paper. The effectiveness of the numerical model is evaluated by experimental tests and parametric studies are conducted to determine influential factors in conceptual column designs. First, three different column designs are analysed: bonded, un-bonded, and un-bonded with additional reinforcing bars. The load-displacement curves and cracking patterns in concrete are obtained and compared with experimental ones. The comparisons indicate that the finite element model is able to reflect the experimental results closely. Both numerical and experimental results show that, the introduction of un-bonded zones in a column end can reduce cracking strains, accordingly reduce the stiffness and strength as well; the addition of extra reinforcement in the un-bonded zones can offset the losses of the stiffness and strength. To decide the proper length of the un-bonded zones and the sufficient amount of the additional reinforcing bars, parametric studies are carried out on their influences. It has been found that the stiffness of un-bonded designs slightly decreases with increasing the length of the un-bonded zones and increases with the size of the additional reinforcing bars.

• Structural Engineering and Mechanics
• /
• v.46 no.5
• /
• pp.615-627
• /
• 2013

One of the most common defects in reinforced concrete bridge decks is corrosion of steel reinforcing bars. This invisible defect reduces the deck stiffness and affects the bridge's serviceability. Regular monitoring of the bridge is required to detect and control this type of damage and in turn, minimize repair costs. Because the corrosion is hidden within the deck, this type of damage cannot be easily detected by visual inspection and therefore, an alternative damage detection technique is required. This research develops a non-destructive method for detecting reinforcing bar corrosion. Experimental modal analysis, as a non-destructive testing technique, and finite element (FE) model updating are used in this method. The location and size of corrosion in the reinforcing bars is predicted by creating a finite element model of bridge deck and updating the model characteristics to match the experimental results. The practicality and applicability of the proposed method were evaluated by applying the new technique to a two spans bridge for monitoring steel bar corrosion. It was shown that the proposed method can predict the location and size of reinforcing bars corrosion with reasonable accuracy.

• Journal of the Korean Geosynthetics Society
• /
• v.6 no.2
• /
• pp.27-32
• /
• 2007

Analysis was performed using AHP (Analytic Hierarchy Process) technique for the determination of priority on the effect factors and the preferences on cut-slope reinforcing methods. The results from professional group, such as researchers, design engineers and construction engineers, show that stability, durability and environmental condition are the most important effect factors. The retaining wall and the cutting methods were predominant for stability, economical efficiency, and maintenance/management in the evaluation of preferences on the cut-slope reinforcing methods interpreted for the increasing method of safety factor.

• Corrosion Science and Technology
• /
• v.4 no.3
• /
• pp.81-88
• /
• 2005

The effects of rebar corrosion on the structural behaviour of reinforced concrete structures were discussed based on recent experimental investigation. The load carrying capacity of the deteriorated beams was quantitatively estimated by evaluating the degree of rebar corrosion in terms of the average cross-sectional loss of longitudinal reinforcing bars and bond deterioration between corroded reinforcing bars and concrete.

• Advances in concrete construction
• /
• v.2 no.3
• /
• pp.163-176
• /
• 2014

Essentially, when electrical current flows easily in concrete that has large pores filled with highly connective pore water, this is an indication of a low resistivity concrete. In concrete, the flow of current between anodic and cathodic sites on a steel reinforcing bar surface is regulated by the concrete electrical resistance. Therefore, deterioration of any existing reinforced concrete structure due to corrosion of reinforcement steel bar is governed, to some extent, by resistivity of concrete. Resistivity of concrete can be improved by using SCMs and thus increases the concrete electrical resistance and the ability of concrete to resist chloride ingress and/or oxygen penetration resulting in prolonging the onset of corrosion. After depassivation it may slow down the corrosion rate of the steel bar. This indicates the need for further study of the effect of electric arc furnace dust (EAFD) addition on the concrete resistivity. In this study, concrete specimens rather than mortars were cast with different additions of EAFD to verify the electrochemical results obtained and to try to understand the role of EAFD addition in influencing the corrosion behaviour of reinforcing steel bar embedded in concrete and its relation to the resistivity of concrete. The results of these investigations indicated that the corrosion resistance of steel bars embedded in concrete containing EAFD was improved, which may link to the high resistivity found in EAFD-concrete. In this paper, potential measurements, corrosion rates, gravimetric corrosion weight results and resistivity measurements will be presented and their relationships will also be discussed in details.

• Steel and Composite Structures
• /
• v.5 no.5
• /
• pp.375-394
• /
• 2005

An experimental study was conducted to develop a new base plate anchorage system for concrete filled tubular column under an axial load and a moment. The column was connected to a concrete foundation using ordinary deformed reinforcing bars that are installed at the inside and outside of the column. In order to investigate the moment resisting capacity of the system, horizontal cyclic loads are applied until the ultimate condition is reached with the axial load held constant. To derive a design method for moment resisting capacity, the reinforced concrete section approach was investigated with the assumption of strain compatibility. The results by this approach agreeded well with those of experiments when the bearing pressure of confined concrete and tangent modulus of steel bars are assumed appropriately. Also, it was found that the column interaction curve can be used to predict the yield strength of the base plate system.

• Fiber Technology and Industry
• /
• v.1 no.1
• /
• pp.97-106
• /
• 1997

• Polymer Science and Technology
• /
• v.6 no.5
• /
• pp.470-480
• /
• 1995

• Proceedings of the Korean Fiber Society Conference
• /
• 2003.10a
• /
• pp.11-12
• /
• 2003

The reinforcing effect of single wall carbon nanotubes (SWNTs) on polyacrylonitrile (PAN) fiber were investigated. The tensile fracture images of the composite fibers demonstrate that SWNTs are well dispersed in PAN matrix as bundles (ropes) ca. 20nm in thickness. It was found that SWNTs play a role not only to reinforce but also to toughen the PAN fiber by increasing breaking strain as well as modulus and strength of the fiebrs. The composite fibers exhibited improved dimensional stability at elevated temperature compared to the neat PAN fiber.

• Journal of the Korean Applied Science and Technology
• /
• v.22 no.2
• /
• pp.91-95
• /
• 2005

Carbon composites were prepared with pitch-based round, C, hollow-type carbon fibers and pitch matrix. The thermal conductivities parallel and perpendicular to the fiber axis were measured by steady-state method. It was found that the thermal conductivities depended on the cross-sectional forms of the reinforcing fibers as well as the reinforcing orientation and carbon fiber precusors. Especially, mesophase pitch-based hollow carbon fiber-carbon composites had the most excellent thermal anisotropy, which was above 100.