• Advances in materials Research
• /
• 제8권1호
• /
• pp.25-36
• /
• 2019

The utilization of fibre in concrete production not only solves the problem of disposing this solid waste but helps conserve natural resources. This study investigated the effect of waste aluminum shavings on bond strength of laterized concrete. Laterized concrete spliced beams of $150{\times}250{\times}2150mm$ and $175{\times}275{\times}2300mm$ were prepared. Fifteen specimens with 16 mm and 20 mm were cast with the addition of aluminium shavings at varying percentages of 1vol%, 1.5vol% and 2vol%; another ten specimens with 16 mm and 20 mm diameter bars at 0% of aluminium shavings were cast as control. Concrete cubes of number were prepared, three taken for each set of various percentages of aluminium shavings were used to determine the concrete strength. It was observed from the analysis that the compressive strength decreased as the percentage of aluminium shavings increased, while the aluminium shavings increased the bond between concrete and steel. However, for normal concrete there was an increase in bond resistance with increase in aluminium shavings. The bond resistance of 16 mm was found to be higher than that of 20 mm in all the specimens tested.

• Structural Engineering and Mechanics
• /
• 제83권6호
• /
• pp.799-810
• /
• 2022

This study investigated the effect of the strengthening efficiency of unbonded steel-bar truss system on the out-of-plane behavior of perforated masonry walls. Four full-scale unreinforced masonry (URM) walls with two different planes were prepared using the unbonded steel-bar truss system and a URM walls without strengthening. All masonry walls were tested under constant axial and cyclic lateral loads. The obtained test results indicated that the pinching effect in the out-plane behavior of masonry walls tends to decrease in the in- and out-of-plane strengthened URM walls using the unbonded steel-bar truss system with the higher prestressing force ratio (R_p) of vertical reinforcing bars in the unbonded steel-bar truss system, regardless of the perforated type of the masonry wall. Consequently, the highest maximum shear resistance and cumulative dissipated energy at peak load in the post-peak behavior were observed in the in- and out-plane strengthened URM walls with the highest R_p values, which are 2.7 and 6.0 times higher than those of URM. In particular, the strengthening efficiency of the unbonded steel-bar truss system was primarily attributed to the vertical prestressed steel-bars rather than the diagonal steel-bars, which indicates that the strains in the vertical prestressed steel-bars at the peak load were approximately 1.6 times higher than those in the diagonal steel-bars.

• Composites Research
• /
• 제35권5호
• /
• pp.359-364
• /
• 2022

Polymers are inherently vulnerable to flame, which limits their application to various high-tech industries. In addition, environmental regulations restrict the use of halogen-based flame retardants which has best flame-retardant effect. There are inorganic flame retardants and phosphorous flame retardants as representative non-halogen-based flame retardants. However, high content of flame retardants is required to impart high flame retardancy of the polymers, and this leads to a decrease in mechanical properties. In this research, a new approach for inorganic flame retardant-based polymer composites with high mechanical properties and flame retardancy was suggested. Inorganic flame retardants called as magnesium oxysulfate whisker (MOSw) were used in this research. MOSw can extinguish fire by releasing water and non-combustible gases when exposed to flame. In addition, they have reinforcing effect when added into the polymer with its high aspect ratio. Expandable graphite (EG) was used as a flame-retardant supplement by helping to form a more dense char layer. Through this research, it is expected that it can be applied to various industries requiring flame retardancy such as automobile, and architecture by replacing halogen-based flame polymer composites.

• 한국산업융합학회 논문집
• /
• 제25권6_3호
• /
• pp.1231-1238
• /
• 2022

In this study, the reinforcement effect of the compression-only bridge seismic reinforcement method, which is mainly applied to old bridges, was studied through SSI analysis. As the analysis conditions, acceleration magnitudes of 0.1g, 0.15g, and 0.2 g were applied, and long-period and short-period seismic waves were applied. As a result of the analysis according to the assumed ground characteristics and structure size, the horizontal displacement at the reinforced section was reduced by about 9%, and the long-period seismic wave had a 95% larger displacement than the short-period seismic wave. In addition, an increase in acceleration of 0.1g resulted in a displacement of about 50%, and a large increase in displacement was observed in long-period seismic waves. As a result of the analysis, in the case of the compression-only bridge seismic reinforcement method, there was a reinforcing effect, so the field applicability was excellent.

• Corrosion Science and Technology
• /
• 제22권2호
• /
• pp.99-107
• /
• 2023

Layered silicate clay montmorillonite (MMT) has been used in nanocomposite coating to improve corrosion protection by reinforcing the barrier property. The better dispersion of MMT in the coating produces a higher barrier effect. Pretreatment with MMT could favor the delamination of clay platelets, facilitating MMT dispersion in the coating. In the present work, a montmorillonite/silica (MMT/Si) composite was prepared by the in situ sol-gel method. x-ray diffraction measurements and field-emission scanning electron microscopy observations showed silica crystal formation and increased basal spacing between the MMT platelets. Composite MMT/Si particles were introduced in an epoxy resin to reinforce the corrosion protection of the coating applied on the AA2024 surface. Electrochemical impedance spectroscopy (EIS) was performed to characterize the protective property of the coating. The results demonstrated the high barrier effect of the coating containing 5 wt% of MMT/Si. Adhesion evaluation after a salt spray test exhibited a high adherence to the epoxy coating containing MMT/Si.

• Steel and Composite Structures
• /
• 제46권1호
• /
• pp.115-132
• /
• 2023

The present study experimentally and analytically investigates the effect of tensile reinforcement ratio and arrangement on the behavior of FRP strengthened reinforced concrete (RC) beams. The experimental part of the program was comprised of 8 RC beams that were tested under four-point bending. Results have shown that by keeping the total cross-section area of tensile reinforcing bars constant, in specimens with a low reinforcement ratio, increasing the number and decreasing the diameter of bars in the section lead to 21% and 29% increase in the load-carrying capacity of specimens made with normal and high compressive strength, respectively. In specimens with high reinforcement ratio, a different behavior was observed. Furthermore, the accuracy of the existing code provisions and analytical models in predicting the load-carrying capacity of the FRP strengthened beams failed by premature debonding mode were evaluated. Herein, a model is proposed which considers the tensile reinforcement ratio (as opposed to code provisions) to achieve more accurate results for calculating the load carrying capacity of FRP strengthened RC beams.

• Corrosion Science and Technology
• /
• 제23권3호
• /
• pp.195-202
• /
• 2024

A zinc mesh sacrificial anode cathodic protection method is recently being developed to protect the reinforced concrete structure in a marine environment. However, comprehensive information regarding the cathodic protection technology applied to reinforced concrete test specimens utilizing zinc mesh sacrificial anodes remains limited. Particularly, no research has investigated the effective range of sacrificial anode cathodic protection in a reinforced concrete structure regarding the transmission of protection current from zinc mesh sacrificial anode to the reinforced concrete structure, particularly concerning effects of temperature variations. This study examined the distribution of potential and current using a long single rebar and several segment reinforcing bars inside a horizontal beam. Vertical pile specimens were applied with a zinc mesh sacrificial anode to simulate concrete bridges or harbor structures. To check the effect of cathodic protection, cathodic protection potential and current of the reinforced concrete specimens were measured and 100 mV depolarization criterion test was performed. It was confirmed that effect of cathodic protection varied depending on resistivity and temperature. The cathodic protection test of pile specimens revealed that the maximum reachable range of cathodic protection current was 10 cm from the waterline as observed in the experiment.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2023년도 가을학술발표대회논문집
• /
• pp.69-70
• /
• 2023

The development of advanced 3D printing technologies has opened up new opportunities for customized digital designs in the construction industry. Using nano- and micro-scale additives is expected to improve the performance of cement-based materials in 3D printing. TiO₂ particles have been widely used as reinforcing additives in cement-based materials. Therefore, this study aims to investigate the application of cement-based materials containing multi-size TiO₂ particles in binder jet 3D printing and the effect of different-size TiO₂ particles on the performance of printed samples. TiO₂ particles exhibit an excellent filling effect, which increases the density of the printed samples and promotes hydration, thereby improving the compressive strength of the samples. In addition, larger TiO₂ particles exert more pronounced filling and photocatalytic effects on the resulting samples.

• 한국환경복원기술학회지
• /
• 제6권3호
• /
• pp.17-28
• /
• 2003

The objective of this study is to review and verify whether the functions and effect of roadside trees generally known in theory are actually realized in urban roads and how well they are performed if the function and effect are really realized. The study was conducted with a focus on air purification effect of roadside trees. The m헤r study result is as follows. First, calculation of air purification effect of roadside trees showed that it is minimal. However, 7.4 units of broad-leaved trees is necessary in order to purify $SO_2$ discharged by one passenger car and 1,803.3 trees to purify $NO_2$. Second, regarding pollutant absorption capacity, air pollutant absorption capacity increased as the number of rows planted gets higher (i.e., 2-row plantation absorbs pollutant better than I-row plantation). In particular, "2-row plantation + lower-level shrub + buffer green belt" was as eight times high as "I-row plantation" in absorption capacity. Third, out of 30 roads with over 8 lanes in 15 cities, only 33.3% or a total of ten roads in seven cities had a median strip. Out of these ten roads, nine roads were planted in a double-layer consisting forest trees, shrubs, ground plants (grass). Analysis showed that out of six tree species planted along these roads, about a half of them were weak to air pollution. Also, based on the outcome of this study, charging a "plantation due" when people purchase a new car, improving layout of roadside trees, and reinforcing plantation of air purification tree species when selecting tree species for roadside trees were proposed.

• 한국전산구조공학회논문집
• /
• 제33권4호
• /
• pp.237-244
• /
• 2020

본 논문에서는 포스트 텐션으로 보강된 아웃리거 벽체의 부등기둥축소량 저감 효과를 확인하였다. 아웃리거 벽체 시스템을 사용할 경우 콘크리트 부재를 아웃리거로 사용하기 때문에 아웃리거 벽체의 장기거동도 고려해야 한다. 아웃리거 벽체은 깊은 보의 형태로 전단 응력이 지배적이기 때문에 전단 응력을 받는 콘크리트의 장기거동에 대한 이론 연구를 수행하였고 그 결과를 유한요소해석에 적용하였다. 아웃리거의 장기거동 고려 시 부등기둥축소량과 아웃리거에 작용하는 전단력을 확인하였으며, 설계 변수인 아웃리거의 두께를 변경해가며 해석하였다. 해석 결과 부등기둥축소량은 증가하고 아웃리거에 작용하는 전단력은 감소함을 밝혔으며 아웃리거의 강성이 작을수록 그 효과가 크다는 것을 밝혔다. 이후 아웃리거의 장기거동으로 인해 증가한 부등기둥축소량을 감소시키기 위해 포스트 텐션 공법으로 보강하는 방법을 제안하고 그 효과를 확인하였다. 프리스트레스 도입 직후의 프리스트레스 손실과 장기거동에 의한 프리스트레스 손실을 모두 고려하였다. 해석 결과 포스트 텐션 공법의 뛰어난 부등기둥축소량 저감 효과를 확인하였으며, 프리스트레스의 크기가 증가할수록 그 효과가 증가함을 밝혔다.