• International Journal of Automotive Technology
• /
• v.6 no.4
• /
• pp.429-436
• /
• 2005

In this paper, operation algorithms are evaluated for a fuel cell hybrid electric vehicle (FCHEV). Power assist, load leveling and equivalent fuel algorithm are proposed and implemented in the FCHEV performance simulator. It is found from the simulation results that the load leveling algorithm shows poor fuel economy due to the system charge and discharge efficiency. In the power assist and equivalent fuel algorithm, the fuel cell stack is operated in a relatively better efficiency region owing to the battery power assist, which provides the improved fuel economy.

• Transactions of the Korean hydrogen and new energy society
• /
• v.27 no.4
• /
• pp.335-340
• /
• 2016

Hydrogen production through proton exchange membrane water electrolysis (PEMWE) is expeditiously receiving international attention for renewable energy sources as well as energy storage system applications due to its environmentally friendly uses. A series of $Ir_{0.2}Ru_{0.8}O_2$ $Ir_{0.5}Ru_{0.8}O_2$ & $IrO_2$ catalysts were synthesized and electrochemically evaluated by using linear sweep voltammetry (LSV) technique. Furthermore, the PEMWE performances of full cells were evaluated by recording I-V Curves. The developed PEMWE stack was also operated in combination with a proton exchange membrane fuel cell (PEMFC) to demonstrate the discrete regenerative fuel cell (DRFC) performances. Produced hydrogen and oxygen from PEMWE were used as a fuel to operate PEMFC to establish a DRFC system.

• Transactions of the Korean hydrogen and new energy society
• /
• v.15 no.1
• /
• pp.23-31
• /
• 2004

For the fabrication of high efficient bifunctional electrocatalyst of oxygen electrode for PEM URFC (Polymer Electrolyte Membrane Unitized Regenerative Fuel Cell), which is a promising energy storage and conversion system using hydrogen as the energy medium, several bifunctional electrocatalysts were prepared and tested in a single cell URFC system. The catalysts for oxygen electrode revealed fuel cell performance in the order of Pt black > PtIr > PtRuOx > PtRu ~ PtRuIr > PtIrOx, whereas water electrolysis performance in the order of PtIr ~ PtIrOx > PtRu > PtRuIr > PtRuOx ~ Pt black. Considering both reaction modes PtIr was the most effective elctrocatalyst for oxygen electrode of present PEM URFC system. In addition, the water electrolysis performance was significantly improved when Ir or IrOx was added to Pt black just 1 wt.% without the decrease of fuel cell performance. Based on the catalyst screening and the optimization of catalyst composition and loading, the optimum catalyst electrodes for PEM URFC were $1.0mg/cm^2$ of Pt black as hydrogen electrode and $2.0mg/cm^2$ of PtIr (99:1) as oxygen electrode.

• Journal of Power System Engineering
• /
• v.21 no.4
• /
• pp.5-17
• /
• 2017

This study focuses on the application of the PEM Fuel Cell(PEMFC) hybrid system, which includes a regenerative braking system with supercapacitor(SC) and battery. The purpose of this study is to evaluate the characteristics of regenerative energy and to propose solutions to increase regenerative energy via vehicle simulation. To achieve this target, we set the rated motor speed to 3,000/2,500/2,000 rpm. Because the flywheel is directly connected to the motor, the generator activates regenerative braking by using the rotational momentum of the flywheel when the flywheel reaches the set speed after the motor stops. We could then measure the characteristics of regenerative braking of voltage, current, power, energy change, etc. Meanwhile, we calculate the storage efficiency of the SC or the battery. Our results show that the SC stores 18% of the regenerative energy, while battery stores 15% of the energy. Since the regenerative energy decreases with the decrease of the motor rotating speed that 5,027 J and 2,915 J are restored at 3,000 and 2,500 rpm, respectively. The experimental results also prove that regenerative braking energy is able to be obtained if and only if the speed of flywheel is over 2,500 PRM, and the efficiency of the system can be further improved.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.24 no.10
• /
• pp.739-744
• /
• 2012

This paper describes the blower performance used for single-stage high pressure regenerative blower. The blower considered is widely applied to the field of a fuel cell system, a medical equipment and a sewage treatment plant. Flow rate and rotating frequency of a impeller of the blower are considered as design parameters for the proper operation of the blower. Three-dimensional Navier-Stokes equations are introduced to analyze the performance and internal flow of the blower. Relatively good agreement between experimental measurements and numerical simulation is obtained. Throughout a numerical simulation, it is found that small and stable vortical flow generated inside the blade passage is effective to increase pressure and efficiency of the blower. Large local recirculation flow having low velocity in the blade passage obstructs the generation of stable vortical flow, thus increases the pressure loss of the blower. Detailed flow field inside the blower is also analyzed and discussed.

• The KSFM Journal of Fluid Machinery
• /
• v.17 no.2
• /
• pp.48-53
• /
• 2014

A low-noise regenerative blower is developed for fuel cell application by combining the FANDAS-Regen code and design optimization algorithm under several performance constraints for flow capacity, static pressure, efficiency and power consumption. The optimized blower design model is manufactured with some impeller modification based on low noise design concept and tested by using aerodynamic performance chamber facility and narrow-band noise measurement apparatus. The measured results of the optimized blower satisfy the performance requirements and are also compared favorably with the FANDAS-Regen prediction results within a few percent relative error. Furthermore, the present study shows the remarkable noise reduction by 26 dBA can be achieved through design optimization and low noise design concept.

• 한국전기화학회:학술대회논문집
• /
• 2003.07a
• /
• pp.173-176
• /
• 2003

• Journal of the Korean Society of Propulsion Engineers
• /
• v.19 no.4
• /
• pp.77-84
• /
• 2015

Recently, as the needs for eco-friendly aero propulsion system increase gradually, many study works have been conducted to develop the hybrid propulsion system for High Altitude Long Endurance(HALE) UAV. In this study, we analyzed both suitable energy distribution and management methodology among the total energy collected from solar cell and the total required energy of aerial vehicle and required energy of the regenerative fuel cell(RFC) for driving in the night time and optimized the energy balance mechanism based on the ascribed mission profile.

• Proceedings of the KIEE Conference
• /
• 2006.04a
• /
• pp.198-200
• /
• 2006

In this paper, three types of power control strategies for controlling a Fuel Cell Hybrid Electric Vehicle(FCHEV) are studied in view of fuel economy. The FCHEV has become one of alternatives for future vehicles since it does emit water only without any exhaust gas while it has a high well-to-wheel efficiency together with an energy saving due to regenerative braking. However, it has also several disadvantages such as the complexity of vehicle system, the increased weight and the extra battery cost. Among various power control strategies, a static power control strategy, a power assist control strategy and a fuzzy logic-based power control strategy are simulated and compared to show the effectiveness of each method.

• Transactions of the Korean hydrogen and new energy society
• /
• v.24 no.4
• /
• pp.320-325
• /
• 2013

TUnitized reversible fuel cells (URFC) combine the functionality of a fuel cell and electrolyzer in one unitized device. For a URFC with proton exchange membrane, a titanium (Ti)-felt is applied to the gas diffusion layer (GDL) substrate at the oxygen electrode, and additionally titanium (Ti)-powders and TiN-powders are loaded in the GDL substrate as a micro porous layer (MPL). Double porous layer with TiN MPL was not acceptable for the URFC because both of fuel cell performance and electrolysis performance are degraded. The double porous layer with Ti-powder loading in the Ti-felt substrate influence rearly for the electrolysis performance. In contrast, the change of pore-size distribution brings a significant improvement of fuel cell performance under fully humidification conditions. This fact indicates that the hydrophobic meso-pores in the GDL play an important role for mass transport.