• Tribology and Lubricants
• /
• v.19 no.5
• /
• pp.251-258
• /
• 2003

New method and device for the on-line measurement of soot concentration in a diesel engine oil are proposed, where the measurement principle is based mainly on attenuated internal total reflection. The detector were evaluated in various ranges of contaminated oils by carbon black particles. It was found that the proposed detector could be well used to monitor the oil deterioration due to soot contamination. Operational range of the detector was found from 0 to 5 mass percentage of soot content. Test results with water and fuel dilution showed that these effects were not remarkable. However, adsorption of carbon black particles onto the measurement surface was considered to be a critical problem of the detector. Effects of particle deposition on the interface was experimentally evaluated with the oil temperature and flow turbulence and discussed throughout this work.

• Korean Journal of Optics and Photonics
• /
• v.27 no.1
• /
• pp.41-46
• /
• 2016

An optical method to measure the three-dimensional (3D) shape of a surface with specular reflection is proposed. The proposed method is based on the analysis of the geometric path of the light from a point source, and the relative displacements of points in the reflection image. The 3D shape of a concave mirror is shown to be determined approximately via experiments, where the vision system consists of LED array illumination, a half-mirror, and an imaging sensor.

• Applied Microscopy
• /
• v.44 no.2
• /
• pp.61-67
• /
• 2014

Layered structures of fiber cell wall of Korean red pine (Pinus densiflora) were investigated by confocal reflection microscopy (CRM). CRM micrographs revealed detailed structures of the fiber cell wall such as S1, S2, and S3 layers as well as transition layers (S12 and S23 layers), which are present between the S1, S2, and S3 layers. Microfibril angle (MFA) measurement was possible for the S2 and S3 layer in the cell wall. The experimental results suggest that CRM is a versatile microscopic method for investigation of layered structures and MFA measurement in individual sub layer of the tracheid cell wall.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.35 no.2
• /
• pp.141-149
• /
• 2015

In the fabrication of electronic circuits used in electronic products, molybdenum thin films are deposited on semiconductors to prevent oxidation. During the deposition, the presence of a particle or dust at the interface between the thin film and substrate causes the decrease of adhesion, performance, and life cycle. In this study, a damage measurement targeting two kinds of glass substrate, with and without particles, was performed in order to measure the change in the molybdenum thin film deposition area in the presence of a particle. Clean and dirty molybdenum thin film specimens were fabricated and directly deposited on a substrate using the sputtering method, and a reflection-type digital holographic interferometer was configured for measuring the damage. Reflection-type digital holography has several advantages; e.g., the configuration of the interferometer is simple, the measurement range can be varied depending on the magnification of a microscopic lens, and the measuring time is short. The results confirm that reflection-type digital holography is useful for the measurement of the damage and defects of thin films.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.3 no.1
• /
• pp.12-18
• /
• 2008

In this research, we proposed a method for high precision measurement than laser displacement measurement. The proposed method finds the causes of error due to change in reflected laser signal level reflected from an object and compensation, and we designed this by applying laser displacement meter.

• Proceedings of the IEEK Conference
• /
• 2002.06a
• /
• pp.211-214
• /
• 2002

In this paper, we present a simple method for characterizing a rectangular waveguide to circular waveguide transition Three standard loads consisting of a short circuit, an offset short circuit 1, and an offset short circuit 2 are sequentially connected to the circular waveguide port and the reflection coefficient at port 1 Is measured for each case. From known reflection coefficients, of standard loads and measured reflection coefficients, the scattering matrix of the transition Is obtained. The proposed method Is verified by the numerical experiment using a commercial software HFSS and by measurments of a actual rectangular-to-circular waveguide transition.

• Proceedings of the Korean Nuclear Society Conference
• /
• 1999.05a
• /
• pp.124-124
• /
• 1999

An ultrasonic method is developed for the measurement of the two-phase mixture level in the reactor vessel or steam generator. The ultrasonic method is selected among the several non¬nuelear two-phase mixture level measurement methods through two steps of selection procedure. A commercial ultrasonic level measurement method is modified for application into the high temperature, pressure, and other conditions. The calculation method of the ultrasonic velocity is modified to consider the medium as the homogeneous mixture of air and steam. and to be applied into the high temperature and pressure conditions. The cross-correlation technique is adopted as a detection method to reduce the effects of the attenuation and the dif.JUsed reflection caused by suface fluctuation. The waveguides are developed to reduce the loss of echo and to remove the effects of obstructs. The present experimental study shows that the developed ultrasonic method measures the two-phase mixture level more accurately than the conventional methods do.

• ETRI Journal
• /
• v.35 no.6
• /
• pp.1148-1151
• /
• 2013

We propose a way to measure the absorber reflectivity at a low cost. Only one simple antenna with a small radiating aperture and a frequency-domain instrument are utilized. The previously used equation for calculating the reflectivity of an absorber is inaccurate, and, therefore, a new equation is derived based on multiple reflection analysis and three test models. Notably, the reflection coefficient of the antenna is included in the derived equation. The accuracy of the proposed method is proven through simulation and measurements. It can be easily applied to a product examination by absorber manufacturers and customers owing to its advantages of simplicity, cost effectiveness, and non-cutting examination.

• Proceedings of the KIEE Conference
• /
• 1989.07a
• /
• pp.158-161
• /
• 1989

This paper describes the AR model of EMG signal during maximum voluntary contraction. By comparing the AR coefficients and the reflection coefficients of the AR model with the median frequency of power spectrum, it if proved that muscle fatigue can be measured by the AR and the reflection coefficients. In the estimation procedure of AR model parameter, the auto-correlation method is superior to the covariance method, and it is determined that the optimal order is six. As the muscle becomes fatigue, the median frequency of power spectrum is declined, and the AR coefficient [$a_1$ ] and the reflection coefficient [$k_1$ ] are also decreased. Therefore the muscle fatigue can be measured by the AR parameter.

• Journal of Magnetics
• /
• v.13 no.2
• /
• pp.70-75
• /
• 2008

In this study, a MOKE (Magneto-optical Kerr effect) measurement method for magnetic nanostructures is proposed. Theoretically, the MOKE signal enhancement can be predicted and confirmed when an anti-reflection coated substrate is used. Since MOKE is a ratio of reflectivity and the difference between the reflectivities for two magnetic states, when the reflectivity of the substrate part is reduced by employing an anti-reflection coated substrate, MOKE signal enhancement can be achieved. The enhancement is confirmed by simple numerical MOKE calculations. When the reflectivity of an anti-reflection coated substrate is 0.7%, the calculated MOKE signal is about 79% of its bulk values for the 100-nm wide Fe nanowire with a 1500-nm radius laser beam. It was found that, for various numerical calculations, a larger MOKE signal is obtained relative to a smaller substrate reflectivity.