• The Transactions of the Korean Institute of Electrical Engineers A
• /
• v.53 no.11
• /
• pp.596-603
• /
• 2004

This paper proposes an expert system based on the pattern recognition method which can enhance the accuracy and effectiveness of real-time bus reconfiguration strategy for the transfer of faulted load when a main transformer fault occurs in the automated substation. The minimum distance classification method is adopted as the pattern recognition method of expert system. The training pattern set is designed MTr by MTr to minimize the searching time for target load pattern which is similar to the real-time load pattern. But the control pattern set, which is required to determine the corresponding bus reconfiguration strategy to these trained load pattern set is designed as one table by considering the efficiency of knowledge base design because its size is small. The training load pattern generator based on load level and the training load pattern generator based on load profile are designed, which are can reduce the size of each training pattern set from max L/sup (m+f)/ to the size of effective level. Here, L is the number of load level, m and f are the number of main transformers and the number of feeders. The one reduces the number of trained load pattern by setting the sawmiller patterns to a same pattern, the other reduces by considering only load pattern while the given period. And control pattern generator based on exhaustive search method with breadth-limit is designed, which generates the corresponding bus reconfiguration strategy to these trained load pattern set. The inference engine of the expert system and the substation database and knowledge base is implemented in MFC function of Visual C++ Finally, the performance and effectiveness of the proposed expert system is verified by comparing the best-first search solution and pattern recognition solution based on diversity event simulations for typical distribution substation.

• Tribology and Lubricants
• /
• v.13 no.1
• /
• pp.42-52
• /
• 1997

This paper deals with wear characteristics of ion-nitrided metal theoretically and experimentally in order to analysis of wear phenomena. Wear tests show that compound layer of ion-nitrided metal reduces wear rate when the applied wear load is mall. However, as th load becomes large, the existence of compound layer tends to increase wear rate. The residual stress at the surface of ion-nitrided metal is measured, and the internal stress distribution is calculated when the normal and tangential forces are applied to the surface of metal. Compressive residual stress is largeest at the compound layer, and decreases as the depth from the surface increases. Calculation shows that the maximum stress exists at a certain depth from the surface when normal and tangential force are applied, and that the larger the wear load is the deeper the location of maximum stress becomes. In the analysis, it is found that under small applied wear load the critical depth, where voids and cracks may be created and propagated, is located at the compound layer, as the adhesive wear, where hardness is an important factor, is created the existence of compound layer reduces the amount of wear. When the load becomes large the critical depth is located below the compound layer, and delamination, which may be explained by surface deformation, crack nucleation and propagation, is created, and the existence of compound layer increases wear rate.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.22 no.9
• /
• pp.628-634
• /
• 2010

This paper presents a feasibility study of a fresh air load reduction system by using an underground double floor space. The fresh air is introduced into the double slab space and passes through the opening bored into the footing beam. The air is cooled by the heat exchange with the inside surface of the double slab space in summer, and heated in winter. This system not only reduces sensible heat load of the fresh air by heat exchange with earth but also reduces latent heat load of the fresh air by ad/de-sorption of underground double slab concrete. In this paper, we proposed a simplified presumption method for the prediction of cooling and heating performance in the system. In conclusion the proposed method has been verified by comparing with the calculated value of the numerical analysis model by using nonlinear two-dimension hygroscopic question.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.31 no.11B
• /
• pp.945-952
• /
• 2006

In hierarchical mobile IPv6 networks, when an inter-domain handover occurs, mobile nodes suffer from excessive signaling traffic and long handover latency, resulting in possible disruption of ongoing connections. Further, the selection of MAP and its load status critically affect the overall system performance. Therefore, we propose a dynamic MAP selection scheme that seeks to distribute load among MAPs as well as reduces inter-domain handovers. Performance is evaluated from not only an analytic model of average signaling cost but also simulation. The analytical and simulation results show that our proposed scheme improves load distributedness and reduces inter-domain handovers and signaling cost compared to another existing IETF based approach.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.22 no.12
• /
• pp.2635-2643
• /
• 1997

In this paepr, a routing algorithm is proposed in order to reduce average end-to-end delay and congesting in the high speed network. The algorithm proposed here uses the existing one which adaptively modifies routes and the amount of traffic allocated to each link as user traffic partterns flutuate. This algorithm is ELB(Equitable Load Balancing). Also, the new algorithm considers the proportional to the distance between source and destination. It reduces congestion from the ELB and average end-to-end delay from the propagation dealy concepts respectively. Through the simulation, it shows that the algorithm proposed here reduces average end-to-end delay over low load to high load, and it also guarantees the congestion control.

• Journal of Aerospace System Engineering
• /
• v.15 no.2
• /
• pp.10-15
• /
• 2021

The propeller wake of tiltrotor-type aircrafts, such as TR-60 and quad tilt propeller (QTP) UAV, in hover substantially impinges the upper surface of the primary wing and generates a downward load. This load is directly proportional to the thrust of the propeller and reduces the available payload. Therefore, wing and nacelle mechanisms should be carefully designed to reduce downward load. This study conducted a numerical analysis of the rotating propeller in hover to predict the downward load of a QTP UAV. An unsteady three-dimensional Navier-Stokes solver was used along with a sliding mesh for the simulation of the rotating propeller. To reduce the downward load, the tilting mechanisms of the partial wing and nacelle were simultaneously introduced and numerically analyzed. Finally, the downward load was predicted by 14% of isolated propeller thrust; further, the downward load could be reduced by adopting the partial wing and nacelle tilting concept.

• Proceedings of the IEEK Conference
• /
• 2006.06a
• /
• pp.209-210
• /
• 2006

Hierachical Mobile IPv6 (HMIPv6) solves Micro-mobility protocol problem about Handover. Mobility Anchor Point(MAP) helps reducing the handover, but this makes a load on the MAP. Besides the MAP operates this work everytime, and every Nodes. In this paper, we propose the algorithm that reduces the amount of Map working.

• Geomechanics and Engineering
• /
• v.23 no.1
• /
• pp.15-30
• /
• 2020

The probabilistic bearing capacity of a strip footing placed on the edge of a purely cohesive reinforced soil slope is computed by combining lower bound finite element limit analysis technique with random field method and Monte Carlo simulation technique. To simulate actual field condition, anisotropic random field model of undrained soil shear strength is generated by using the Cholesky-Decomposition method. With the inclusion of a single layer of reinforcement, dimensionless bearing capacity factor, N always increases in both deterministic and probabilistic analysis. As the coefficient of variation of the undrained soil shear strength increases, the mean N value in both unreinforced and reinforced slopes reduces for particular values of correlation length in horizontal and vertical directions. For smaller correlation lengths, the mean N value of unreinforced and reinforced slopes is always lower than the deterministic solutions. However, with the increment in the correlation lengths, this difference reduces and at a higher correlation length, both the deterministic and probabilistic mean values become almost equal. Providing reinforcement under footing subjected to eccentric load is found to be an efficient solution. However, both the deterministic and probabilistic bearing capacity for unreinforced and reinforced slopes reduces with the consideration of loading eccentricity.

• Journal of Industrial Technology
• /
• v.26 no.B
• /
• pp.233-242
• /
• 2006

Continuous, discrete and semi continuous HMM systems are used for the speech recognition. Discrete systems have the advantage of low run-time computation. However, vector quantization reduces accuracy and this can lead to poor performance. Continuous systems let us get good correctness but they need much calculation so that occasionally they are unable to be used for practice. Although there are semi-continuous systems which apply advantage of continuous and discrete systems, they also require much computation. In this paper, we proposed the way which reduces calculation for continuous systems. The proposed method has the same computational load as discrete systems but can give better recognition accuracy than discrete systems.

• Journal of Institute of Control, Robotics and Systems
• /
• v.17 no.7
• /
• pp.714-719
• /
• 2011

This paper proposes a scheme for distributed load balancing in mobile communication networks based on supervisory control framework. Using load information exchanged with neighboring cells, the "supervisors" that reside in the base stations distribute load among cells by controlling handover parameters in a distributed manner. The supervisors are designed so that the load difference among neighboring cells are kept under a pre-defined value. Results from systematic analysis and simulation indicate that our scheme effectively balances traffic load among cells and reduces call blocking rate of the overloaded cells.