• Journal of the Korean Society of Safety
• /
• v.20 no.2 s.70
• /
• pp.105-112
• /
• 2005

This is to find out that cement mortar mixed with waste tie particle can be applied for recycling it and enhanced to have shock absorption capacity. Therefore, architectural material specification and its related references for the disposal of it are based on for the study. Test has been performed with procedure, based on the Korea Standard insulation mortar and Compressive Strength Test has been done at K remicon factory approved by Korea Government in Korea, in order to decrease any possible error in mixing procedure. Test molds far insulation capacity and cohesive strength have been delivered to the expert agency for having more exact results. The result from the above test shows that waste tyre mixed with cement mortar has almost equal to the common concrete. This means that the recycling of the waste t)re will be demanded more and more in case of having continued development for this recycling area. And also waste t)to-using construction material can be more applied for construction area than existing material. Thus, this recycling method can be very usefully applied for solving environmental problem and for establishing economic aspect.

• Journal of the Korean Society for Precision Engineering
• /
• v.17 no.8
• /
• pp.5-14
• /
• 2000

The treatment of technical consumer products after using is important for the conservation of our environment. In this paper the demanufacturing technology that is required to maximize the recycling rate of end-of-life products is introduced, The definitions including types of the recycling are described. The factors that have to regard in the design stage of products in order to maximize the recycling rate of the products are introduced. The objective assessment methods for the design for environment are described. Finally disassembly process and future prospect of the automations are discussed.

• Journal of the Korean Society of Safety
• /
• v.18 no.1
• /
• pp.76-80
• /
• 2003

There will be a big problem in disposing of waste tie coming from the cars. Because many of these have been thrown away to the field and environmentally polluted. New, We need to find out how to dispose or recycle these waste material. It is thought that recycling this material especially mixing with concrete will be a good idea. This study is focused how each material do its behavior due to the size of waste type particle and its amount into concrete material. 0.4mm-10mm range of particle has been applied to the material : Also, 1.0%, 1.5%, 2.0% range of tyre particle proportion has been applied to make cylinder molds. The concrete mold with waste-tyre particle has vibration-absorbing ability. It is found that 0.4 -0.6mm particle mixing concrete has been more solid organized. And this waste tyre material could be applied to the general concrete, it is found.

• Journal of the Korea Concrete Institute
• /
• v.24 no.4
• /
• pp.465-472
• /
• 2012

This research aims to find an effective mixing method for controlled low strength material (CLSM) using diverse recycled industrial byproducts. This study is a fundamental research to develop and commercialize a resource-recycling CLMS that can greatly contribute to cost reduction and environmental stress relief. In the past, few studies have been performed on CLSM in Korea. This research is expected to provide fundamental data not only for development and commercialization of the resource-recycling CLSM satisfying required material performances but also serve as a ground breaking study on utilization of recycled material in construction industry and ultimately leading to advanced resource-recycling practices at national level. From the comprehensive analysis of minimum unit quantity for maximum strength and material segregation prevention, it was found that the optimal mixing condition for mixing FSD, RSID and SD material to filler-aggregate ratio (f/a) was approximately 50.

• Resources Recycling
• /
• v.16 no.2 s.76
• /
• pp.32-39
• /
• 2007

The measurement of physicochemical properties of ASR incineration ash has been carried dot and the preparation of light-weight material has also been performed using ASR ash for recycling point of view as building or construction materials. For this aim, chemical composition, particle size distribution, and heavy metal leachability were examined for 2 bottom ashes and 4 fly ashes obtained from the domestic ASR incinerator. In the present work, attempt has been made to prepare the lightweight material using boiler ash as a raw material, which is prepared by forming the mixture of boiler ash, lightweisht filler and inorganic binder and followed by calcination at elevated temperature. As a result, the content of Cu in bottom ash was as high as about 3wt% so that the recovery of Cu from ash was required. The major compound of SDR #5 and Bag filter #6 was found to be $CaCl_2{\cdot}Ca(OH)_2{\cdot}H_2O\;and\;CaCl_2{\cdot}4H_2O$, respectively. It is thought that heavy metal teachability of lightweight material prepared with boiler ash was significantly decreased due to the encapsulation or stabilization of heavy metal compounds.

• Nuclear Engineering and Technology
• /
• v.51 no.4
• /
• pp.1037-1040
• /
• 2019

For the past 50 years, graphite has been widely used as a moderator, reflector and fuel matrix in different kinds of gas-cooled reactors. Resulting in approximately 250,000 metric tons of irradiated graphite waste. One of the most significant long-lived radioisotope from graphite reactors is carbon-14 ($^{14}C$) with a half-life of 5730 years, this makes it a huge concern for deep geologic disposal of nuclear graphite (NG). Considering the lifecycle of NG a number of waste management options have been developed, mainly focused on the achievement the radiological requirements for disposal. The existing approaches for recycling depend on the cost to be economically viable. In this new study, an affordable process to remove $^{14}C$ has been proposed using samples taken from the Nuclear Power Plant in Latina (Italy) which have been used to investigate the capability of organic and inorganic solvents in removing $^{14}C$ from exfoliated nuclear graphite, with the aim to design a practicable approach to obtain graphite for recycling or/and safety disposed as L& LLW.

• Resources Recycling
• /
• v.13 no.1
• /
• pp.59-67
• /
• 2004

A universal plasma-chemical module (PChM) for the industrial processing of different hydrocarbon raw material pyrolysis was designed and tested. Laboratory investigations for the plasma-chemical method of acetylene production from natural gas and different coals were made. Similar laboratory tests on the industrial production of acetylene as a raw material for organic syn-thesis were developed using the PChM. A comparison of the suggested plasma-chemical method with the traditional process of acetylene production were carried out. The outlook of the plasma-chemical method was shown.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.31 no.2
• /
• pp.34-41
• /
• 1999

Adsorption of cationic polyacrylamide dry strength resins onto the surface of papermaking fibers and fines is critical for their effective utilization. Since dry strength resins are frequently employed when recycled fibers containing a great deal of fines are used as a raw material, their adsorption characteristic onto the recycled fiber fines is of great importance. In this study, effects of recycling on adsorption characteristics of cationic polyacrylamide onto primary and secondary fines were examined. Never dried bleached hardwood kraft pulp was beaten and dried for recycling. In each recycling step the adsorption characteristic of a cationic PAM onto primary and secondary fines was evaluated by kjeldahl nitrogen analysis method. The influence of recycling on water retention value and carboxyl content along with the sheet density and tensile strength was examined. Secondary fines of never dried pulp adsorbed twice as much of C-PAM as the primary fines, however, the adsorption capacity of the secondary fines decreased rapidly during the course of recycling and showed lower adsorption capacily than primary fines.

• Resources Recycling
• /
• v.12 no.1
• /
• pp.65-74
• /
• 2003

As new functional electronics are being developed fast, the commercialization rate of advanced battery as a power source proceeds rapidly. Lithium battery is satisfying the needs of high-energy source for its lightness and good electrochemical property. Especially lithium ion battery, adopted as a new power source for portable electronic equipments around the globe, has been mass-produced. Under the circumstance, the generation of lithium battery wastes is becoming a new environmental problem. In this paper, we are going to inspect technology developments for recycling of lithium battery wastes and scraps in domestic and foreign area, and to suggest how to treat domestic lithium battery wastes and scraps better.

• Resources Recycling
• /
• v.18 no.1
• /
• pp.13-21
• /
• 2009

A research on material separation of EVA and PET mixture plastic waste using a triboelectrostatic separator has been carried out. It was found that PP was the best charging material to give the highest charge on the surface of EVA and PET mixture plastics with an opposite polarity. Therefore, a charger of pipe line type using PP material was manufactured for separation of EVA and PET mixture plastic waste. At optimum test conditions that used PP cyclone charger developed in this study, we could separate out PET with a glade of 98.7% and a recovery of 89.7%.