• 펄프종이기술
• /
• 제44권3호
• /
• pp.70-78
• /
• 2012

For evaluating the printing suitability of electronic copying papers in the aspect of climate conditions, 12 samples of copying papers being generally used in Korea and worldwide were collected. The copying papers were controlled by various temperature and humidity options in conditioning equipment in order to simulate the specific circumstances of dry, temperate or tropical climate, and the pre-heating system of photocopying machines during printing. As results, some copying papers showed several physical problems, especially in recycled copying papers and a normal paper with original printing faulty. These problems of copying papers were mostly resulted in extremely high moisture circumstance, and in lower levels of tensile strength and tensile stiffness. The moisture contents of copying papers during passing through the pre-heater system of photocopying machine could be rapidly decreased because paper is exposed to high temperature around the pre-heating zone. The copying paper, for example of XR3 sample, containing low moisture contents below 2% had high exfoliating possibility of toner transfer from copying paper.

• 펄프종이기술
• /
• 제43권2호
• /
• pp.49-56
• /
• 2011

Mulching technique is used to control the temperature and moisture content of soil by covering the ground surface. Most kinds of mulching film are made of polyethylene which is non-biodegradable synthetic polymer. Utilizing these films has been one of the main sources in soil pollution. Thus residual films under the ground should be removed after a certain period of time. Therefore, an alternative mulching material made of biodegradable functional paper is considered instead of non-biodegradable films. The mulching sheet produced from paper basis has a functionality to be naturally degraded and then recycled to the bio-materials on soil. In this study, the paper based-mulching sheet coated with biodegradable polymer was specially produced using a laboratory bar coater. Coating colors prepared by dissolving PBS/PLA in chloroform were applied to kraft paper. The mechanical strength and aging properties of this mulching sheet were investigated. The burst strength of polymer-coated paper was decreased with the increase of the PBS ratio in PBS/PLA blends, and, in particular, 30/70 blending condition led to good stability in heat-aging atmosphere for 60 days.

• 콘크리트학회논문집
• /
• 제13권4호
• /
• pp.346-353
• /
• 2001

본 연구는 얇은 시멘트판 제품의 보강재로써 건조공정에 의해 생산된 폐지섬유의 최적 배합비를 도출하기 위하여 수행되었다. 이를 위해 순수 목질섬유 대비 폐지섬유의 대체수준을 세분화하여 실험을 실시하였으며, 슬러리-탈수 공법을 사용하여 폐지섬유보강 시멘트 복합체를 제조하였다. 본 연구는 실험적 연구와 반응표면 분석법을 활용한 통계적 분석을 통해 공정인자(가압, 비가압)과 섬유보강재 조건(섬유혼입율, 순수섬유 대체수준)을 최적화하였다. 최적화된 재생 폐지섬유 시멘트 복합체를 기술적으로 분석하였으며, 그 결과, 폐지섬유보강 시멘트 복합체의 성능과 경제적 측면에서 폐지섬유의 재활용이 가능하리라 판단된다.

• 펄프종이기술
• /
• 제47권4호
• /
• pp.160-167
• /
• 2015

The reduction of energy consumption in papermaking process has been considered as one of the major issue in the paper technology. The energy efficiency of paper mill becomes more significant for the mill which manufacture the board grade products such as linerboard with recycled paper such as OCC. The application of lignocellulose spacer to the board grade paper stock would be the feasible solution by increasing the paper bulk and the drying efficiency. The major defects originated from the application of the lignocellulose spacer could be the loss of strength properties. In this study, the ways for improving the strength properties of the spacer-added linerboard were suggested and evaluated. The effects of the addition of various types polyelectrolytes were tested and the different methods of polyelectrolytes were applied for finding the efficient way. The pretreatments of lignocellulose spacer with the polyelectrolytes during wood spacer hydration resulted in the higher strength properties than the typical application method such as the addition to the mixed stock. Multilayer treatments of the spacer with polyelectrolytes were also evaluated and leaded to the higher strength properties with the similar bulk improvement.

• 펄프종이기술
• /
• 제33권2호
• /
• pp.58-67
• /
• 2001

MOW (Mixed Office Waste) mainly consisted of photocopied paper is being recycled to produce tissue or fine paper products. Toner particles that are fused and set on paper surface in photocopying process turns into large and plate-shaped particles after repulping which prevents them to be removed effectively in flotation deinking. The immediate purpose of this study is to find the effective deinking technology that increases the recycling potential of photocopied papers for manufacturing tissue and fine paper products. In this study the effects of pulping temperature and the type of hydrophobic groups of nonionic surfactants on the deinking efficiency of photocopied paper has been investigated. Particle size distribution of the toner particles after pulping and flotation, brightness, yield and ash removal were investigated. The size of toner particles after pulping increased as the pulping temperature was increased. When pulping at the low temperature finer toner particles were generated, however, greater amount of toner particles was found to attach to the fiber. When the pulping temperature was greater than Tg of the toner, the amount of coarse hairy particles increased. When nonionic surfactants with a double bond in hydrophobic groups were used, toner removal efficiency, brightness and ash removal were increased. As the addition level of surfactant was increased, yield decreased rather sharply without improving brightness.

• 펄프종이기술
• /
• 제37권4호통권112호
• /
• pp.44-51
• /
• 2005

Paper mills use and discharge lots of water. And so now the papermaking industry could be classified into major water consuming industry In order to analyze the process water network and to establish the mass, water balance of duplex board mill, computer aided simulation was made using water pinch method. Based on the pinch analysis results, reuse of process water, after regenerating by microfilter as much as $140\;m^3/hr$, could be suggested without significant accumulation of contaminants in process water. According to this suggestion about $3000\;m^3/day$ of recycled process water could be sub stituted by regenerated water and consequently $30\%$ of energy cost is expected to be reduced.

• 대한안전경영과학회지
• /
• 제9권4호
• /
• pp.83-90
• /
• 2007

This study is to find out if it can be recycled for making better concrete. Therefore, waste paper as of newspaper and newspaper are added into concrete to see if waste paper-mixing concrete can have any particular characteristic. The test result of paper concrete was compared and analyzed through four kinds of tests such as compressive strength as of a fundamental one of concrete resistant capacity against heat. $200^{\circ}C,\;400^{\circ}C\;and\;600^{\circ}C$ heated concrete were compressively tested in order to find out concrete strength resistant to high temperature. heat capacity was also tested, based on the expectancy of its low conductivity. finally flexural strength test using four reinforced concrete beams with size of $20cm{\times}30cm{\times}160cm$ was made. And concrete property exposed to the temperature showed that there are almost not effect for the strength up to $400^{\circ}C$, but it was decreased down to 50% of the original condition. volume of paper mixed with concrete without relation to paper kinds of new and waste one.

• 한국건설순환자원학회논문집
• /
• 제1권1호
• /
• pp.81-88
• /
• 2005

플라이애쉬를 콘크리트 혼화재로 사용할 경우 수화열의 저감, 내화학성의 증대, 건조수축의 저감, 장기강도의 개선 등의 여러 가지 장점이 있으나, 3일 이내의 초기강도 발현이 낮은 점과 성분중의 미연탄소분의 영향으로 인하여 AE제 흡착에 의한 공기량의 변동 등의 몇 가지 이유로 인하여 일부 공사를 제외하고는 일반적으로 10% 전후만을 사용하고 있다. 본 연구에서는 플라이애쉬 사용량을 시멘트량의 최대 30%까지 치환하고, 이때 발생할 수 있는 초기강도를 개선하기 위하여 무기질계 혼합재인 CSA 및 제지애쉬를 플라이애쉬 사용량의 8, 20%를 혼합하여 조기강도 특성 및 미소수화열 발생에 의한 조기강도 개선 가능성에 분석을 하였다. 미소수화열 측정결과 플라이애쉬를 10, 20, 30% 치환한 경우 강도에 영향을 줄 수 있는 제 1 Peak의 발열량 및 발현 시간이 OPC 배합보다 낮고 늦게 나타나고 있으며, CSA 및 제지애시를 혼입할 경우 발열량이 증가하고 시간도 단축되는 것으로 나타났다. 특히 제지애시를 혼합할 경우 강도에 영향을 줄 수 있는 제 2 Peak의 발현 시간 및 발열량이 OPC와 유사한 것으로 나타났다. 응결시간의 경우 CSA 및 제지애시를 혼입할 경우 플라이애쉬 배합보다 단축되는 것으로 나타났으며, 이는 미소수화열 발열량과 상관성이 있는 것으로 나타났다. 압축강도의 경우 플라이애쉬 배합에 CSA 및 제지애시를 혼입항 경우 조기강도 증진효과가 있는 것으로 나타났으며, 특히 제지애시를 혼입할 경우 강도 증진이 효과적으로 나타나는 것으로 분석되었다. 따라서 플라이애쉬를 다량 사용할 경우 이에 따르는 조기강도 하락 방지에 CSA 및 제지애시가 효과적으로 사용될 수 있을 것으로 검토되었다.

• 펄프종이기술
• /
• 제33권1호
• /
• pp.24-29
• /
• 2001

The base paper of corrugated board is mainly produced from Korean old corrugated container (KOCC), and thus the recycling rate of KOCC is very high. However, there is a problem that the pulp quality is very low while the recycling rate of OCC is high. The fines content in KOCC, the main source of the corrugated board, amounts to nearly the half of the total stock, and its formation increases as recycling process repeats due to the hornification of fiber. There have been attempts to improve the drainage property of OCC by increasing the headbox concentration of the paper machine or by applying drainage-promoting polymer additives. However, these conventional methods have problems of weakened paper strength and lowered converting fitness caused by paper formation hindrance. The strength of linerboard could not be increased in case KOCC is used, because hornified OCC pulp can-not be sufficiently refined due to the lowered drainage property caused by fines formation. We studied about a new technique consisting of froth-flotation for fractionating pulp stock into a long fiber portion and fines fraction. This study will be developed in order to enhance the drainage and strength properties of a recycled OCC pulp by selective treatment of flocculant on fractionated OCC Fines.

• 펄프종이기술
• /
• 제33권2호
• /
• pp.1-7
• /
• 2001

Use of high yield pulp and recycled fiber as raw materials and water system closure result in higher fines content and buildup of organic and inorganic contaminants in white water. These are detrimental for the effectiveness of chemical additives including retention aids. Thus it is imperative to employ a retention systems that maintains its efficiency in closed papermaking system for reducing fresh water consumption. The performance of four different microparticle retention systems including cationic polyacrylamide (C-PAM)/bentonite, highly charged cationic starch (HCS)/silica, C-PAM/micropolymer, cationic guar gum (CGG)/silica was evaluated and compared at three different levels of papermaking system closure. Buildup of detrimental substances in a closed white water system increased cationic demand and finally reduced the performance of retention systems. Cationic starch and guar gums maintained their effectiveness in retention in closed white water systems contaminated with anionic trashes because of their structural rigidity and hydrogen bonding ability. Particularly, cationic guar gums, due its stiffness of molecular structure, appeared perform better than catinonic starch.