• Advances in concrete construction
• /
• 제10권4호
• /
• pp.319-332
• /
• 2020

The impacts of reinforcing concrete matrix with steel fibers, polypropylene fibers and recycled plastic fibers using different volume fractions of 0.15%, 0.5%, 1.5% and 2.5% on the compressive and tensile characteristics are experimentally investigated in the current research. Also, flexural behavior of plain concrete (PC) beams, shear performance of reinforced concrete (RC) beams and compressive characteristics of both PC and RC columns reinforced with recycled plastic fibers were studied. The experimental results showed that the steel fibers improved the splitting tensile strength of concrete higher than both the polypropylene fibers and recycled plastic fibers. The end-hooked steel fibers had a positive effect on the compressive strength of concrete while, the polypropylene fibers, the recycled plastic fibers and the rounded steel fibers had a negative impact. Compressive strength of end-hooked steel fiber specimen with volume fraction of 2.5% exhibited the highest value among all tested samples of 32.48 MPa, 21.83% higher than the control specimen. The ultimate load, stiffness, ductility and failure patterns of PC and RC beams in addition to PC and RC columns strengthened with recycled plastic fibers enhanced remarkably compared to non-strengthened elements. The maximum ultimate load and stiffness of RC column reinforced with recycled plastic fibers with 1.5% volume fraction improved by 21 and 15%, respectively compared to non-reinforced RC column.

• 펄프종이기술
• /
• 제39권3호
• /
• pp.1-11
• /
• 2007

To evaluate the quality of waste paper used for the manufacture of linerboard, the types of papers and foreign materials in compressed waste paper currently used were investigated. The recycled fibers were obtained from printing paper, newspaper, wrapping paper, white coated paperboard and corrugated container. Their fibers were observed by using a microscope, and the mechanical properties of the recycled papers manufactured from the recycled fibers were investigated. The compressed wastepaper was composed of 54% paperboard, 20% printing paper, and 20% newsprint. The content of foreign materials was about 4%, showing higher contents compared to 1% of foreign substances provided by Korea paper manufacturers' association. The types of foreign materials were various, which include vinyls, plastics, metals, woods, styrofoams, and cloths. Sound fibers were generally observed in the recycled fibers of printing papers and wrapping paper. The recycled fibers of white coated board, corrugated container and newsprint showed to be generally damaged. The whiteness of each recycled fiber were highly affected by pulp bleaching and ink-particle mixing conditions. The values of breaking length and burst index were lower than those for corrugating medium and liner board specified in KS. Although the anatomical characteristics of recycled fibers varied, their strengths appeared to be similar. This result may be explained by the use of non-deinked fiber.

• 한국펄프종이공학회:학술대회논문집
• /
• 한국펄프종이공학회 2006년도 PAN PACIFIC CONFERENCE vol.1
• /
• pp.99-103
• /
• 2006

Use of recycled fibers in papermaking has been increased for economical and environmental reasons. Recycled panels are major liber resources for brown grades and newsprints. Since the recycled fibers have disadvantageous properties as raw materials for papermaking it is of great importance to optimize the use of these recycled fibers. OCC (Old Corrugated Containers) is the major fiber source for linerboards and corrugating mediums that require diverse specification in strength properties. Many studies have been focused to overcome the problems of strength reduction of brown grades when recycled fibers are used as raw materials. The problem of strength loss for papers made from recycled fibers is closely associated with the increased amount of fines in recycled fibers and hornification of fibers. Fines contained in the recycled fiber resources cause problems not only in paper properties but also in process runnability. This shows that the optimal management and proper use of fines in recycling papermaking system are critical to get most benefits of using recycled fibers. In this study some approaches for optimal use of fiber fines in recycled paper mill have been investigated. Stock samples, prepared in the laboratory and obtained from a recycling plant were used. Fractionation of these samples was made using Sweco screen. And the effect of the addition of polyelectrolytes including cationic PAM and PEI on drainage and retention was evaluated. Different methods of polymer addition were compared to find the most effective ways of treating recycled fiber stocks with polyelectrolytes. Addition of polyelectrolytes to the short fiber fraction was most effective in retention and drainage. The influence of the charge and molecular weight of these two polymers has been examined and discussed.

• 한국펄프종이공학회:학술대회논문집
• /
• 한국펄프종이공학회 2001년도 추계학술발표논문집
• /
• pp.183-199
• /
• 2001

Alternative way of shaping fibers suitable for papermaking was introduced. Impact refining, which was done simply by hitting wet fibers with a metal weight vertically, was intended to keep the fibers from shortening and to cause mostly internal fibrillation. Virgin chemical pulp, its recycled one and OCC were used in the experiment. It was noticed from the experiment that impact refining on virgin chemical pulp kept the fiber length and Increased bonding properties greatly, However, in the recycled fibers from the chemical pulp, fiber length and bonding properties were decreased. In OCC, which seems to contain fractions of semi-chemical pulp and mechanical pulp (GP), and which is recycled pulp from corrugated boxes, fiber length and bonding properties were decreased disastrously. We believe recycled cellulosic fibers (recycled chemical pulp and OCC in this case), which went through hornification, were less resistant to the mechanical impact than virgin chemical pulp. For virgin chemical pulp, impact refining allowed no significant fiber length shortening, high WRV, and high mechanical strength.

• 펄프종이기술
• /
• 제46권6호
• /
• pp.94-102
• /
• 2014

The physical and chemical properties of recycled fibers from mixed waste paper are more and more deteriorated because of unknown history of recycling times. In order to improve the mechanical properties of liner paper, the recycled fibers from wasted cotton clothes were used in papermaking process, and their applicabilities were evaluated in several points of fiber modification. Thus, two kinds of fiberizing methods from waste cotton clothes were considered by using rotary sandpaper and grinder mill. Finally, the rotary sandpaper method was relatively desirable in preserving longer fiber length and fibrillated fiber surface. The recycled cotton fibers by swelling treatment with NaOH and bleaching with reductive chemicals were mixed with OCC fibers, and the handsheets were prepared to basis weight of $80g/m^2$ and evaluated the mechanical properties of paper. The fibrous properties showed outstanding results in freeness and WRV improvements by alkali treatment and high brightness by reductive bleaching treatment. The physical and mechanical properties of sheet by mixing OCC fibers and recycled cotton fibers were also highly improved in tensile, burst strength and specially folding resistance.

• 펄프종이기술
• /
• 제31권1호
• /
• pp.31-38
• /
• 1999

Adsorption of polymeric flocculants and dry strength agents onto the surface of papermaking fibers is critical for their effective utilization since the polymeric substances not adsorbed on fibers or fines keep recirculating in the papermaking system to cause various operational difficulties and loss of raw materials. Problems associated with the unadsorbed polymeric substances generate great attention because unprecedent interests in utilization of recycled papers and papermaking system closure. In this study, to understand the effects of recycling on the adsorption propensity of cationic polyacryamide (PAM) dry strength resin onto hardwood bleached kraft pulp fibers and fines a systematic approach was followed. Never dried bleached hardwood kraft pulp was recycled in two different ways. In mode one recycling experiment never dried pulp was beaten then recycled three times by employing simple drying and disintegrating steps. In mode two recycling experiment beating of the recycled pulp was carried out after each recycling step. Adsorption of cationic PAM on fibers and fines was evaluated employing Kjeldahl nitrogen analysis method. The influence of recycling on water retention value, carboxyl content, sheet density and tensile strength of the pulp was examined. As the number of recycling increased, water retention value of the fiber was reduced due to hornification and this in turn caused a decrease in adsorption of cationic PAM. On the other hand, the carboxyl content of the recycled fibers increased because of the oxidation of fibers occurred during drying, and this caused an increase in adsorption of cationic PAM. Because of these two opposing factors the adsorption of the cationic PAM on the recycled fibers decreased and then increased slightly at third recycling step. Increase of PAM adsorption, however, did not provide did not provide and strength improvement for the recycled pulp fibers indicating greater influence of the honification on interfiber bonding.

• 대한토목학회논문집
• /
• 제28권3A호
• /
• pp.401-406
• /
• 2008

본 연구에서는 폐 PET병을 사용하여 구조적으로 효과가 있는 재생 PET섬유를 생산하였고 세 가지 형상의 재생 PET섬유와 시멘트 매트릭스와의 부착성능을 평가하였다. 또한 세 가지 형상의 재생 PET섬유로 보강된 콘크리트의 휨성능 시험을 실시하였다. 시험결과 재생 PET섬유는 우수한 부착성능의 증가를 보여주었다. 휨시험 결과 재생 PET섬유는 콘크리트의 휨인성을 증가시킨다는 것을 증명하였다. 부착 및 휨시험 결과를 기본으로 요철형 재생 PET섬유의 부착 및 휨성능이 다른 형상의 섬유와 비교하여 가장 우수하였다.

• 펄프종이기술
• /
• 제34권5호
• /
• pp.56-62
• /
• 2002

Alternative way of shaping fibers suitable for papermaking was introduced. Impact refining, which was done simply by hitting wet fibers with a metal weight vertically, was intended to keep the fibers from shortening and to cause mostly internal fibrillation. Virgin chemical pulp, its recycled one and OCC were used in the experiment. It was noticed from the experiment that impact refining on virgin chemical pulp kept the fiber length and increased bonding properties greatly. However, in the recycled fibers from the chemical pulp, fiber length and bonding properties were decreased. In OCC, which seems to contain fractions of semi-chemical pulp and mechanical pulp (GP), and which is recycled pulp from corrugated boxes, fiber length and bonding properties were decreased disastrously. We believe recycled cellulosic fibers (recycled chemical pulp and OCC in this case), which went through hornification, were less resistant to the mechanical impact than virgin chemical pulp. For virgin chemical pulp, impact refining allowed no significant fiber length shortening, high WRV, and high mechanical strength.

• Advances in concrete construction
• /
• 제9권2호
• /
• pp.195-205
• /
• 2020

In this study, effect of recycled aggregates and polypropylene fibers on the response of conventionally reinforced concrete element subjected to tensile loading in terms of tension stiffening and strain development was experimentally investigated. For this purpose, concrete prisms of 100 × 100 mm cross section and 500 mm length having one central deformed steel re-bar were cast using fibrous and non-fibrous Recycled Aggregate Concrete (RAC) with varying percentages of recycled aggregates (0%, 25%, 50%, 75% and 100%) and tested under uniaxial tensile load. For all fibrous RAC mixes, polypropylene fibers were used at constant dosage of 3.15 kg/㎥. Effect of recycled aggregates and fibers on the compressive strength of concrete was also explored in this study. Through studying tensile load versus global axial deformation of composite and strain development in concrete and steel, it was found that replacement of natural aggregates with recycled aggregates in concrete negatively affected the cracking load, tension stiffening and strain development, and this negative effect was observed to be increased with increasing contents of recycled aggregates in concrete. The results of this study showed that it was possible to minimize the negative effect of recycled aggregates in concrete by the addition of polypropylene fibers. Reinforced concrete element constructed using concrete containing 50% recycled aggregates and polypropylene fibers exhibited cracking behavior, tension stiffening and strain development response almost similar to that of concrete element constructed using natural aggregate concrete without fiber.

• Computers and Concrete
• /
• 제24권3호
• /
• pp.193-206
• /
• 2019

Although concrete is the most widely used construction material, its deficiency in shrinkage and low tensile resistance is undeniable. However, the aforementioned defects can be partially modified by addition of fibers. On the other hand, possibility of adding waste materials in concrete has provided a new ground for use of recycled concrete aggregates in the construction industry. In this study, a constant combination of recyclable coarse and fine concrete aggregates was used to replace the corresponding aggregates at 50% substitution percentage. Moreover, in order to investigate the effects of fibers on mechanical and durability properties of recycled aggregate concrete, the amounts of 0.5%, 1%, and 1.5% steel fibers (ST) and 0.05%, 0.1% and 0.15% polypropylene (PP) fibers by volumes were used individually and in hybrid forms. Compressive strength, tensile strength, flexural strength, ultrasonic pulse velocity (UPV), water absorption, toughness, elastic modulus and shrinkage of samples were investigated. The results of mechanical properties showed that PP fibers reduced the compressive strength while positive impact of steel fibers was evident both in single and hybrid forms. Tensile and flexural strength of samples were improved and the energy absorption of samples containing fibers increased substantially before and after crack presence. Growth in toughness especially in hybrid fiber-reinforced specimens retarded the propagation of cracks. Modulus of elasticity was decreased by the addition of PP fibers while the contrary trend was observed with the addition of steel fibers. PP fibers decreased the ultrasonic pulse velocity slightly and had undesirable effect on water absorption. However, steel fiber caused negligible decline in UPV and a small impact on water absorption. Steel fibers reduce the drying shrinkage by up to 35% when was applied solely. Using fibers also resulted in increasing the ductility of samples in failure. In addition, mechanical properties changes were also evaluated by statistical analysis of MATLAB software and smoothing spline interpolation on compressive, flexural, and indirect tensile strength. Using shell interpolation, the optimization process in areas without laboratory results led to determining optimal theoretical points in a two-parameter system including steel fibers and polypropylene.