• Journal of Advanced Marine Engineering and Technology
• /
• v.22 no.4
• /
• pp.529-537
• /
• 1998

Currently as due to the rapid development of industry and increase in population we meet serious problems concerning the shortage and pollution of water. In the country many experts predict a shortage of water approaching 450 million tons by the year 2006. To cope with this serious problem it is necessary to construct desalination plants. In the adoption of a desalination system the most important factor is the cost of fresh water production,. In general LNG is stored in a tank as a liquid state below $-162^{\circ}C$. When it is serviced, however the LNG absorbs energy from a heat source and transforms to a high pressure gaseous state. During this process a huge amount of cold energy accumulated in cooling LNG is wasted. This wasted cold energy can be utilized to produce fresh water by using a sea water freezing desalination system. In order to develop a sea water freezing desalination system and to establish its design technique qualitative and quantitative data regarding the freezing behavior of sea water is required in advance, The goals of this study are to reveal the freezing behavior of sea water is required in advance. The goals of this study are to reveal the freezing mechanisms of sea water to measure the freezing rate and to investigate the freezing heat-transfer characteristics,. The experimental results will provide a general understanding of sea water freezing behavior in a rectangular vessel cooled from above.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.18 no.8
• /
• pp.2051-2056
• /
• 2014

This paper investigated the separation of magnetic signal from a ferro-magnetic object. The magnetic signals were ILM(induced longitudinal magnetization) and IVM(induced vertical magnetization), which were induced by earth magnetic field and PLM(permanent longitudinal magnetization) and PVM(permanent vertical magnetization), which were due to a permanent magnetization of the object, respectively. Magnetic signal separation was based on the fact that magnetization vector could be analyzed according to longitudinal and vertical directions. Also the influence of non-uniform magnetic field from a rectangular coil on the separation was examined. A military vessel with a size close to rectangular coil has more errors on the magnetic signal separation.

• International Journal of Ocean System Engineering
• /
• v.3 no.4
• /
• pp.175-187
• /
• 2013

Moonpools are vertical wells in a floating body used onboard many types of vessels like Exploration and drilling vessels, Production barges, Cable-laying vessels, Rock dumping vessels, Research and offshore support vessels. Moonpool gives passage to underwater activities for different types of ships as per their mission requirements. It is observed that inside a moonpool considerable relative motions may occur, depending on shape, depth of the moonpool and on the frequency range of the waves to which the ship is exposed. The vessel responses are entirely different in zero and non-zero Froude number. Former situation is paid attention in this study as the mission requirement of the platform is to be in the particular location for long period of operation. It is well known that there are two modes of responses depending on the shape of the moonpool viz., piston mode for square shape and sloshing mode for rectangular shapes with different aspect ratios of opening like 1:1.5 and 1:2 ratios. Circular shaped moonpool is also tested for measuring the responses. The vessel moored using heavy lines are modelled and tested in the wave basin. The pretensions of the lines are varied by altering the touchdown points and the dynamic tensions on the lines are measured. The different modes of oscillations of water column are measured using wave gauge and the vessel response at a particular situation is determined. RAOs calculated for various situations provide better insight to the designer.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.47 no.4
• /
• pp.300-315
• /
• 2011

The investigation for the catch and species composition in the deep sea of the East Sea was done to search marine organisms using some kinds of traps with small commercial fishing vessel near Goseong, Korea from 2008 to 2009. The experiments was carried out with some different traps at the depth of 200m, 400m, 700m and 1,000m. In 2008, the amount of catch with rectangular, cone and drum net traps was 91.4kg with twelve trips and the proportion of catch with rectangular and cone traps was high. Dominant species caught were Aniwan whelk (57%), snow crab (12%), hunchback sculpin (7%) and red snow crab (5%). The catch of Aniwan whelk was done well with rectangular and cone traps at the depth of 700-1,000m. Snow crab was mainly caught with rectangular and cone traps at the shallower depth of 200m, while red snow crab caught a lot with cone trap at the deeper depth of 700m. In 2009, the amount of catch with rectangular, cone and round traps was 92.4kg with nine trips. The proportion of catch with round trap was higher than that with cone trap. Dominant species caught were snow crab (67.1%), Aniwan whelk (14.8%) and northern shrimp (9.8%). Snow crab was caught well with round trap at the depth less than 400m.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2015.10a
• /
• pp.1109-1112
• /
• 2015

A milatary ship without degaussing coil has a vertical magnetization to compensate magnetization induced by the vertical magnetic field component of earth magnetic field during demagnetization process. Flash D is very useful to acquire vertical magnetization. However this is hard to predict vertical magnetization. This experiment was investicated on another method, which used the only vertical bias magentic field. The specimens were prepared by thin Zn coated steel sheet with a thickness of 0.15mm. The shapes of 3 specimes was rectangular, triangular and circular cylinders. These shapes were corresponded to the shapes of bow, mid and stern of a vessel. Through FEM analysis, the difference of magnetic signatures for these specimens was recognized and the residual magnetization curve was measured. magnetic field was generated by a solenoid coil and magnetic signature was measured by a magnetic field sensor. A linearity between a vertical bias magnetic field and a vertical manetzation existed and the vertical magnetization of a miltary vessel was predicted by the linearity.

• The KSFM Journal of Fluid Machinery
• /
• v.5 no.2 s.15
• /
• pp.29-35
• /
• 2002

The present study is concerned with the flow patterns induced by various impellers in a rectangular tank. Impellers are FBT (Flat blade turbine), PBT (Pitched blade turbine), Shroud turbine, Rushton turbine, and Helical ribbon turbine types. The solutions of flows in moving reference frames require the use of 'moving' cell zone. The moving zone approaches are based on MRF (Multiple reference frame), which is a steady-state approximation and sliding method, which is an unsteady-state approximation. Numerical results using two moving zone approaches we compared with experiments by Ranade & Joshi, which have done extensive LDA measurements of the flow generated by a standard six-bladed Rushton turbine in a cylindrical baffled vessel. In this paper, we simulated the flow patterns with above-mentioned moving zone approaches and impellers. Turbulence model used is RNG $k-{\epsilon}$ model. Sliding-mesh method is more effective than MRF for simulating the rectangular tank with inlet and outlet. RNG $k-{\epsilon}$ model strongly underestimates the velocity of experimental data and velocity by Chen & Kim's model, but it seems to be correctly predicted in overall distribution.

• Journal of architectural history
• /
• v.18 no.6
• /
• pp.103-126
• /
• 2009

This study aims to discover historical trends and change of form of all stupas in India with observation of field study that is as direct as possible, by classifying, analyzing, and synthesizing the stupas. Study of Indian stupa in Korea has a number of shortcomings since only introductory partial approach has been made in order to seek the origin of Korean pagoda. This study also aims to correct errors of stupa terminology in Chinese character committed by misinterpretation of Hindi language which was established by precedent Japanese scholars several decades ago. Piled-up stupas were totally destroyed by pagans, therefore their remains tell us only of structure, material, sizeand disposition. However remains of carved stone at torana and drum give us clues as to the original form of stupa and worshipping activity, as well as change to a more luxurious form. Many rock cave stupas of India show us both simple forms matching the ascetic age of early Buddhism and luxurious changes in Mahayanan era introducing us to statues of Buddha. Indians recovered the spheric form of 'anda,' a Hindi term meaning cosmic egg, from the hemispheric form of the piled-up stupa. Therefore we might discard the erratic term of 'bokbal', which means an upset vessel. Railings and parasols became main factors of stupa design. Carved railings around stupa became a sign of divinity. Serious worshipping activity made drums long or high and created multi-embossed stripes. Bases of circular drums of some cave stupas changed their shapes to rectangular or octagonal. Single parasols became multiparasols of affluent flowerlike curved stems on carved stupa. Multistoried, elongated and high parasols of Gandhara stupas are closely related to such factors as diverse changes of form in Indian subcontinent. Four-sided torana gate and ayaka column of the circular form of original stupas suggest the rectangular form of subsequent East Asian pagoda, and higher and wider base of Indian stupas became the origin of East Asian rectangular pagoda.

• Journal of Ocean Engineering and Technology
• /
• v.30 no.3
• /
• pp.201-207
• /
• 2016

In this paper, an aluminum pressure vessel (cylinder) for a 200 m water depth is designed and analyzed. Because of their lack of usage in the deep sea, only a few papers about pressure vessels subjected to external pressures have previously been published. Moreover, the high level of imported external-pressure-vessel products limits the academic pursuit. Yet, research on internal pressure vessels is widely available because of their broad usage at onshore. This paper presents the process of basic designing and modelling of pressure vessels using the design rules of American Standard of Mechanical Engineering (ASME) Section VIII Division 1. To promote understanding, finite element analysis (FEA) result of an existing sample cylinder which was not designed by ASME code is compared with the design obtained in this paper. Several methodologies are used for the finite element analysis, including rectangular, cylindrical, and axisymmetric coordinate, to attain an accurate stress result. Same dimensions except the thickness of the cylinder and loading condition of 0.200 MPa was given for the current study. Finally, a rigorous design procedure is added for the bolt and boundary conditions of the cylindrical body and its ends. The obtained stress level satisfies the allowable design stress value specified in the ASME code.

• Journal of Ocean Engineering and Technology
• /
• v.33 no.2
• /
• pp.99-105
• /
• 2019

Unlike typical a dynamic positioning (DP) system, a DP-assisted mooring system must determine a set point (SP) that can ensure a mooring tension safety range to prevent an excessive increase in mooring tension. In this paper, a new algorithm for determining the SP is suggested in order to reduce the tension on all the mooring lines. To determine the SP, a working area around the vessel is represented by a rectangular grid. Thus, the size of the grid area is limited considering the offset of a vessel with a mooring system. At each grid's nodes, the resultant tension from all the mooring lines is estimated using the time history of the tension and vessel's position. The results of static analyses for each grid position are used to estimate the global tension. Consequently, the SP is automatically selected as a position satisfying criterion for minimizing the total tension. In order to validate the suggested algorithm, a motion simulation with the control system in the time domain and a discussion of the results are presented.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.41 no.2
• /
• pp.47-54
• /
• 2009

Anatomical characteristics of kenaf were investigated in transverse, radial and tangential direction by optical and scanning electron micrograph. Kenaf was made up of bast fibers, wood fibers, vessels and parenchyma cells. Bast fibers were long slender cells with different types of pits. The shape of wood fibers were in various ways and pointed at the ends. The pits were observed on the surface of bast fibers. Kenafs were diffuse and radial porous. and composed of solitary pores and two or three radial pore multiples. Various types of vessels were observed. The pits showed alternate pitting and larger diameter than other cells. Parenchyma cells were rectangular or square with different shapes of pith parenchyma cells compared to conventional types of parenchyma cells in wood. The number of pith on the surfaces were small.