• Proceedings of the Korea Electromagnetic Engineering Society Conference
• /
• 2002.11a
• /
• pp.293-296
• /
• 2002

In this paper, we proposed a beam tilting microstrip patch array antenna for the reception of satellite signals by using low cost copper etched polyester films and foams. The configuration and coupling mechanism of the proposed antenna are similar to the dipole Yagi-Uda antenna. It is composed of 3 layers of polyester films and three layers of foam. In order to prevent unwanted radiation and coupling loss by microstrip feeding networks and parasitic patches, a stacked layer with rectangular slots above the driver patch array is inserted. The 16${\times}$8 element microstrip Patch way antenna is Presented by experimental results. Its beam patterns are affected by many parameters such as sizes of the patches, gap between the patches. characteristics of the substrates, feeding method, etc. Owing to its complexities of various design parameters, both simulation and experiment were performed. The fabricated antenna received DBS signal from KOREASAT 3 by doing nothing but adjusting azimuth direction.

• Journal of electromagnetic engineering and science
• /
• v.13 no.4
• /
• pp.214-223
• /
• 2013

This paper proposes a theoretical analysis of hidden device detection and a design of multiband circular polarization patch array antenna for non-linear junction detector system application. A good axial ratio of circular polarization patch antenna is realized by a new approach that employs inclined slots, two rectangular grooves and a truncated ground for the conventional antenna. A good axial ratio of the 1.5 dB lower is measured by having an asymmetric gap distance between the ground planes of the coplanar waveguide feeding structure. The common ground plane of the linear array has an optimum trapezoidal slot array to reduce the mutual coupling without increasing the distance between the radiators. The higher gain of about 1 dBi is realized by using the novel common ground structure. The measured return loss, gain, and axial ratio of the proposed single radiator, as well as the proposed array antennas, showed a good agreement with the simulated results.

• Proceedings of the IEEK Conference
• /
• 2007.07a
• /
• pp.157-158
• /
• 2007

In this paper, an internal wideband DVB-H antenna using parasitic patch is proposed. The antenna consists of rectangular patch with system ground and shorting plate. The -10 dB impedance bandwidth of proposed antenna is about 530 MHz ($470{\sim}1000\;MHz$). Radiation patterns are nearly omni-directional for operating frequency. It is suitable for DVB-H application.

• Proceedings of the KIEE Conference
• /
• 2006.07c
• /
• pp.1613-1614
• /
• 2006

In this paper, a $4{\times}4$ rectangular patch array antenna operated at 20 GHz is implemented for the satellite communication. Two $2{\times}2$ subarrays are designed and more efficient $2{\times}2$ subarray is used for the design of $4{\times}4$ patch array. The sixteen patch antennas and microstrip feeding line are printed on the single-layered substrate. The spacing between the array elements is chosen to be $0.736{\lambda}$. HPBW (Half-Power Beam Width) is 17.6 degrees in the E-plane and 18.7 degrees in the H-plane with a gain of 17.2SdBi in the simulation results.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.20 no.6
• /
• pp.738-745
• /
• 2014

In this paper, It is performing to the elastic and elasto-plastic large deformation series analysis using a numerical method for the initial deflection effect of the aluminum alloy rectangular plate in the elasto-plastic loading area patch loading size. It is assumed a boundary condition to be a simply supported condition and consider the initial deflection amplitude, aspect ratio. It examined the critical elastic buckling load and post-buckling behaviour of aluminium alloy A6082-T6 rectangular plate. It used a commercial program for the elastic and elasto-plastic deformation series analysis. If the initial deflection amplitude is smaller, the in-plane rigidity with increasing to load is reduced from the start and occurs significantly more increasing the amplitude. More higher the aspect ratio, the initial yield strength is gradually decreased, and the plate thickness thicker and occurs larger than the thin walled plate a reduction ratio of the initial yield strength of the patch loading size as 0.5.

• Journal of Advanced Navigation Technology
• /
• v.27 no.1
• /
• pp.71-76
• /
• 2023

In this paper, a humidity sensor using a microstrip patch antenna(MPA) and polyvinyl alcohol(PVA) is studied. PVA is a polymer material whose permittivity changes with humidity, and a rectangular slot is added to the radiating edge of the MPA, which is sensitive to changes in electric field, in order to increase the sensitivity to changes in relative permittivity. After thinly coating the area around the radiating edge with the rectangular slot of the MPA fabricated on a 0.76 mm-thick RF-35 substrate with PVA, the changes in the resonant frequency and magnitude of the MPA's input reflection coefficient are measured when relative humidity is adjusted from 40% to 80% in 10% increments at a temperature of 25 degrees using a temperature and humidity chamber. Experiment results show that when the relative humidity increases from 40% to 80%, the resonance frequency of the antenna' input reflection coefficient decreases from 2.447 GHz to 2.418 GHz, whereas the magnitude increases from -7.112 dB to -3.428 dB.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.24 no.1
• /
• pp.1-10
• /
• 2013

In this paper, a broadband planar monopole antenna for multi-band services is proposed. The physical size of the proposed antenna is miniaturized by folding a rectangular loop. And a resonance point in the 3.9 GHz band is reduced by a coupling phenomenon with the central part of the T-shaped patch and the folded rectangular loop. In addition, the T-shaped patch is inserted to the rectangular shaped monopole antenna due to deriving the broadband frequency characteristics. The frequency characteristic is optimized by adjusting the gap and length of the folded rectangular loops and a transverse diameter of the T-shaped patch. The antenna dimensions including the ground plane are $40{\times}60{\times}1.6mm^3$. It is fabricated on the FR-4 substrate(${\epsilon}_r$=4.4) using a microstrip line of $50{\Omega}$ for impedance matching. In the measured result, the bandwidth corresponding to the VSWR of 2:1 is 162 MHz(815~977 MHz) and 2,530 MHz(1.43~3.96 GHz). For analyzing the human effect by the proposed antenna, 1 g and 10 g averaged SARs are simulated and measured. As the simulated results, 1 g-averaged SAR is 1.044 W/kg, and 10 g-averaged SAR is 0.718 W/kg. This result are satisfied by the SAR guidelines which are 1.6 W/kg(1 g-averaged) and 2.0 W/kg(10 g-averaged).

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.43 no.5 s.347
• /
• pp.169-175
• /
• 2006

In this paper, a microstrip patch antenna with the T-shaped slits is designed and fabricated for GPS. The resonant frequency of the microstrip patch antenna with the slits is lower than that of a microstrip patch antenna without the slits so it can be reduced the size of patch. In order to calculate resonant frequency of the microstrip patch antenna with the slits, the resonant frequency formulas are derived from the surface current distribution on microstrip patch antenna. Using the Ensemble 6.0 simulation tool, the accuracy of approximate equations is verified. The microstrip patch antenna with the slits is designed by using these equations. The size of the designed antenna with T-shaped slits can be reduced to 29% compared with that without the slits. The microstrip patch antenna with slits have a very narrow bandwidth. In order to improve the narrow bandwidth of microstrip patch antennas with the slits, a microstrip patch antenna with rectangular slot is proposed. As the result of the measurements, the resonant frequency of the proposed microstrip patch antenna with the T-shaped slits is 1.575GHz and the bandwidth is about 50MHz.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.13 no.11
• /
• pp.5447-5451
• /
• 2012

This paper presents a pattern-switchable microstrip patch antenna with loop structure. The loop structure for switchable radiation beam pattern is connected with feeding line of the microstrip patch antenna. As changing switch on/off state, the radiation beam pattern can be changed. The target frequency is 2.4 GHz and maximum radiation gain is 3.2dBi. The proposed antenna is useful for diversity antenna and smart antenna in modern wireless communication including MIMO (Multi-Input Multi-Output) and WLAN system. The sizes of the rectangular patch and the ground plane are $28mm{\times}28mm$ and $40mm{\times}50mm$, respectively. The simulation and experimental results show that the antenna radiation pattern can be changed with switch on/off configuration.

• Journal of Advanced Navigation Technology
• /
• v.23 no.5
• /
• pp.415-423
• /
• 2019

In this paper, a design method for a high-sensitivity microstrip patch sensor antenna (MPSA) loaded with a bent-slot was studied for the permittivity measurement. The bent-slot similar to a single-ring complementary split ring resonator was added along a radiating edge of the patch in order to enhance the sensitivity to the permittivity. The sensitivity of the proposed MPSA was compared with that of a conventional rectangular MPSA and a thin rectangular-slotted MPSA. Three MPSAs were designed and fabricated on a 0.76-mm-thick RF-35 substrate so that the input reflection coefficient would resonate at 2.5 GHz in the absence of the superstrate under test. When five different Taconic substrates with a relative permittivity ranging from 2.17 to 10.2 were used as the superstrate under test, experiment results show that the sensitivity of the proposed MPSA, which is measured by the shift in the resonant frequency of the input reflection coefficient, is 4.1 to 6.1 times higher than that of the conventional MPSA.