• Restorative Dentistry and Endodontics
• /
• 제21권1호
• /
• pp.227-241
• /
• 1996

The effect of collagen dissolution in acid conditioned dentin was morphologically examined by both scanning and transmission electron microscopy. 18 freshly extracted human molars and dentin bonding systems of All Bond 2, Scotchbond Multipurpose, Superbond D-Liner were used in this study. For SEM preparation, each 3 of ~ exposed dentin surfaces were acid conditioned by using various acids within the above three bonding systems respectively. After acid conditioning of the other 3 exposed dentin surfaces as above, they were treated with 1.7% NaOCl for 2 minutes. The remaining 3 dentin surfaces were acid conditioned and treated with 3.3 % NaOCl for 2 minutes. All of the specimens were then fixed in 4 % glutaraldehyde for 12 h at $4^{\circ}C$ and dehydrated in ethanols grades from 50 % to 100 %, then surface changes of the specimens were observed by using SEM. For TEM preparation, exposed dentin surfaces were acid conditioned with the same acid as SEM specimens and treated with 1.7%, 3.3 % NaOCl respectively, then applied with corresponding bonding agents. After the procedures were finished, composite resin were applied on the dentin surfaces and light cured. Small, rectangular sticks with end dimensions of approximately 1 by 1 mm were sectioned and further sample preparative techniques for transmission electron microscopy were performed in accordance with the procedures used for ultrastructural TEM observations of calcified tissues. The results were as follows : 1. In the 1.7 % NaOCl retreated specimens after acid conditioning, the porous dentin surface of intertubular dentin and wide opening of dentinal tubules were appeared. And there were fine irregularities on the intertubular dentin, indicating a clear difference as compared with the acid conditioned specimens. 2. In the 3.3% NaOCl retreated specimens after acid conditioning, the intertubular dentin was further eroded causing a more porous and wider opening of dentinal tubules. Moreover, sharp irregularities on the intertubular dentin were more evident than those of acid conditioned and 1.7% NaOCl retreated specimens. 3. In all of the acid conditioned specimens, the resin-dentin hybrid layer of approximately 3.5mm thickness was formed and the collapsed collagen layer was observed on the uppermost part of hybrid layer in the specimens applied with All Bond 2. The collgen fibrils of intertubular dentin in specimens applied with Scotchbond Multipurpose were running perpendicular to the interface, and electron dense black layer demarcated from the deep unaltered dentin was more evident in the specimen applied with Superbond D-Liner than any other specimens. 4. In the 1.7 % NaOCl retreated specimens after acid conditioning, the resin-dentin hybrid layer of approximately 2.5-3.0mm thickness was formed and the collapsed collagen layer and longitudinally running collagen fibrils as shown in the acid conditioned specimens were observed in the specimens applied with All Bond 2 and Superbond D-Liner. 5. In all of the 3.3% NaOCl retreated specimens after acid conditioning, the evidence of resin-dentin hybrid layer was not identified ; nevertheless, the longitudinally running collagen fibrils remained slightly in the specimens applied with All Bond 2.

• 한국가구학회지
• /
• 제17권2호
• /
• pp.57-68
• /
• 2006

This study understands rockers of today and supplies basic data of design and manufacture studying pattern change of rockers arisen in West, there is the purpose. Also, this study is investigated by dividing theoretical background of rockers, 7 kinds of American traditional rockers and European rockers from 18th century to opening part of 20th century and contemporary rockers since 20th century. The theoretical background and the style of 2 rockers (Windsor rocker, Boston rocker) were investigated to study the stylistic changes of rockers. Originally a rocker was invented by a European farmer around 1700. It developed to a household which equip practicality and comfortablness in the United States than Europe. Early rockers in a primal form appeared in the 1740s in the United States. American early rockers connected skate to established chair bridge. Rockers are deep connection with family's emotion. Rockers can provide playing functions for children and medically treating functions for adults. Windsor Rockers developed by attaching skate is mammy bench and according to shape of back form bow or hoop-back rocker, birdcage rocker, comb-back rocker. Windsor Rockers formed peculiar American tradition of craftsman furniture through structure that have a unique back of a chair and round seat. Boston Rockers were the first chairs made by mass production method. They show a particular shape with S-curve style seat and rectangular crest at the upper part of the back. Often Crests were decorated by stenciled pattern with curled leaves such as rosettes and scrolled designs.

• 대한기계학회논문집B
• /
• 제26권5호
• /
• pp.703-709
• /
• 2002

In order to investigate the smoke movement in three dimensional room fires, the center fire, wall fire and corner fire plume in different sized fires were studied experimentally by rectangular pool fire using methanol as a fuel. As the fire size became larger for the center fires placed at the center of the floor, the air flow rate entrained through the opening, average hot layer temperature, flame angle deflected backwards and mean flame height was observed to increase. On the other hand, as the fire size became smaller, the neutral plane height in the door and time reached steady-state was observed to decrease. The average hot layer temperature, mean flame height and doorway neutral plane height obtained from comer fire were higher than those produced by wall fires and center fires. The simple model for describing the effect of walls on the mean flame height was presented. It was shown that the model provides a good description of the present measurements, when used with the assumption by Hansell(1993), that the increase of the average flame height is equal to the ratio of the open to the total perimeters of the trays. Also the two models for predicting the effects of walls on the mean flame height were presented. These models overestimated the measured values of the mean flame height above fuel trays close to a wall and in a corner by approximately 19-26%, respectively.

• 한국식품영양과학회지
• /
• 제15권4호
• /
• pp.51-55
• /
• 1986

본 계량적 분체 낙하봉지는 현재 사용하고 있는 4각형 합성수지제 분체 포장의 구조를 개조하여 최종 용기로써 계량적 사용이 가능 하도록 봉지 몸체에 분체 박하유도 튜브를 연결하고 그 튜브 끝단에 개폐용 핀을 채운 구조이다. 이 계량적 분체 박하봉지는 현재 사용하고 있는 분체 봉지에 비해서 봉지의 개봉이 쉽고, 분획 사용 후 재 밀봉이 긴밀하게 될 수 있으며, 재 밀봉이 철저하게 되므로 흡방지 및 anti-caking효과가 크다. 그리고 먼지나 곤충과 같은 이물질의 혼입이 없으며 계량적 사용으로 경제적이고 환경과 하수의 오염을 최소화 하는 효과가 있다. 또한 개봉후 세워둘 때 넘어져 엎지러져 일어나는 손실이 없는 등의 장점이 있다. 따라서 본계량적 분체 낙하봉지는 분상의 설탕, 소금, MSG와 같은 조미료, coffee 및 세제는 물론 농약의 계량적 사용에 실용성을 줄 것으로 생각된다.

• 한국안전학회지
• /
• 제8권4호
• /
• pp.107-113
• /
• 1993

Small rectangular explosion chamber of its size 25cmX25cmX32cm with a circular bursting diaphram at the top was used to study the mechanism of gas explosion to fire transition phenomena, the process of ignition of solid combustibles during a gas explosion. To visulize the explosion to fire transition phenomena, transparent acryl window and high speed camera system were used. The test piece of solid combustible in this experiments was a 5cm$\times$5cm square sheet of newspaper which was placed in the explosion chamber filled with a LPG-air mixture. The mixture was ignited by an electric spark at the center of the chamber. Explosion to fire transition phenomena and the behavior of out flow and in flow of gas through the opening yielded by bursting the diaphram was visualized with shlieren system and without shlieren system. Diameter of a bursting dlaphram at the top of the explosion chamber was varied 5cm, 10cm, and 15cm, and the position of test piece were varied with 6 point. Explosion pressure was measured with strain type pressure transducer, and the weight difference of the test piece before and after each experimental run was measured. By comparing the weight difference of solid combustibles before and after the experiment and the behavior of out flow and inflow of gas after explosion, it was found that the possibility of ignition was depends on the LPG-air mixture concentration and the exposure period of test piece to the burnt gas. Test result of this experiments it was found that the main factor of this phenomena are that heat transfer to the test piece, and the pyrolysis reaction of test piece. Based on the results, the mechanism of the explosion to fire transition phenomena were inferred ; gas explosion- heat transfer to solid combustibiles ; pyrolysis reaction of solid combutibles : air inflow ; mixing of the pyroly gas with air ignition.

• 대한조선학회논문집
• /
• 제60권2호
• /
• pp.120-134
• /
• 2023

In this study, hydrodynamic characteristics of dam break flow were investigated by a series of experiments. The experiments were performed in a 2-D rectangular flume with obtaining instantaneous images of dam break flow to capture the free surface elevation, and pressure distributions on vertical wall and bottom of the flume. The initial water depth of the dam break flow was changed into 3 different heights, and the gate opening speed was changed during the experiments to study the effect of the gate speed in the dam break flow. Generation of dam break phenomena could be classified into three stages, i.e., very initial, relatively stable, and wall impact stages. The wall impact stage could be separated into 4 generation phases of wall impinge, run-up, overturning, and touchdown phases based on the deformation of the free surface. The free surface elevation were investigated with various initial water depth and compared with the analytic solutions by Ritter (1892). The pressures acting on the vertical wall and bottom were provided for the whole period of dam break flow varying the initial water depth and gate open speed. The measurement results of the dam break flow was compared with the hydrodynamic characteristics of green water phenomena, and it showed that the dam break flow could overestimate the green water loading based on the estimation suggested by Buchner (2002).

• 한국농촌건축학회논문집
• /
• 제24권4호
• /
• pp.133-139
• /
• 2022

This study deals with the formation of Jongyeonbangjeok's Gwangju Factory in the 1930's to 80's, and the findings are shown below: In the period of formation, the factory was rectangular-shaped from north to south, and the structure was located at the center of the site, and in the east of it, there was a dormitory connected from south to north. The building was arranged with an open area on the south. In the east of the site where company houses were located, same-sized structures were arranged along the axis.In the period of change, the factory was restored about the damage from the Korean War, and it went through the process of division into two companies. As a result, the factory in the center of the site was divided into left and right ones, and the dormitory and the group of company houses were, too, divided into two, so division was made largely into southern and northern parts. In the period of stabilization, along with factory extension in each of the companies, welfare for factory workers was expanded by building more houses or opening sport facilities. After the 1980's, too, the existing factories were either extended or remodeled according to the induction of equipment, and some showed changes in their functions due to a fire or such.

• 대한토목학회논문집
• /
• 제30권1A호
• /
• pp.61-69
• /
• 2010

일반적으로 비부착 프리캐스트 콘크리트 교각은 철근콘크리트 교각에 비하여 내진성능과 지진 후의 공용성능이 우수하다. 본 연구에서는 OpenSEES 프로그램을 사용하여 비부착 프리캐스트 교각의 내진거동을 분석하였다. 특히, 콘크리트 강도, 긴장재의 초기 긴장비, 긴장재 비, 교각 세그먼트의 크기의 변화에 대한 비부착 프리캐스트 콘크리트 교각의 내진거동에 대하여 해석적으로 연구하였다. 해석결과 긴장재 비 및 초기 긴장비가 증가함에 따라 연화상태 및 극한상태시의 휨강도도 증가하였다. 콘크리트 강도 및 세그먼트 크기에 따른 교각의 휨강도 차이는 거의 무시할 만 하였으나, 초기 긴장비의 증가는 긴장재의 항복 시점을 앞당기는 결과를 나타냈다. 또한, 심부콘크리트의 압축 변형률이 극한변형률에 미치지 않으므로, 일반 콘크리트교각에 비하여 심부구속 철근량을 감소시킬 수 있을 것으로 사료된다.

• Restorative Dentistry and Endodontics
• /
• 제16권2호
• /
• pp.85-98
• /
• 1991

The aim of this study was to investigate the effect of low - power laser used in the medical field for various purposes to suppress pain responses evoked by noxious electrical or mechanical stimuli. After both inferior alveolar nerves and the left anterior digastric muscle of cats under general anesthesia were exposed, a recording electrode for the jaw opening reflex was inserted into the anterior digastric muscle. The right inferior alveolar nerve was dissected under a surgical microscope until the response of the functional single nerve could be evoked by the electrical stimulation of the dental pulp or oral mucosa. The electrical stimulus was applied with a rectangular pulse of 10 ms duration for measuring the threshold intensity of a single nerve fiber in the inferior alveolar nerve which responds to stimulation of dental pulp and oral mucosa. Then a pulse of 1 ms duration was applied for determination of conduction velocity. A noxious mechanical stimulus to the oral mucosa was applied by clamping the receptive field with an arterial clamp. The Ga-As diodide laser(wave length, 904 nm ; frequency, 1,000 Hz) was irradiated to the prepared tooth cavity, inferior alveolar nerve and oral mucosa as a pulse wave of 2 mW for 6 minutes. This was followed by a continuous wave of 15 mW for 3 minutes. The action potential of the nerve and EMG of the digastric muscle evoked by the noxious electrical stimulus and nerve response to noxious mechanical stimulus were compared at intervals of before, immediately after, and at 5, 10, 20, 40, 60 minutes after laser irradiation. The results were as follows: The conduction velocity of the intrapulpal $A{\delta}$- nerve fiber recorded from the inferior alveolar nerve before irradiation had a mean value of $6.68{\pm}2.07m/sec$. The laser irradiation did not affect the conduction velocity of the AS - nerve fiber and did not change the threshold intensity or amplitude of the action potential either. The EMG of the digastric muscle evoked by noxious electrical stimulation to the tooth was not changed by the laser irradiation, whether in latency, threshold intensity or amplitude. The laser irradiated to the receptive field of the oral mucosa which was subjected to noxious stimuli did not affect the amplitude of the action potential or the frequency either.

• 한국터널지하공간학회 논문집
• /
• 제8권4호
• /
• pp.325-334
• /
• 2006

시계조절이나 설해방지 목적으로 설치되는 캐노피 구간 내에서의 기류유동특성의 이해는 정상환기 뿐만 아니라 비상시 대처방안 강구를 위한 요건이다. 또한 터널 방재시스템 설계를 위하여서는 종단구배, 평면선형, 단면크기 및 형태 등과 같은 터널의 다양한 특성이 화재확산에 미치는 영향에 대한 정량적인 이해가 필요하다. 본 연구에서는 국내도로터널의 전형적인 특성을 적용한 터널에 캐노피가 된 경우와 종단 및 선형구배, 단면적 및 형태, 곡선구간이 환기 및 화재확산에 미치는 영향을 CFD분석함을 목적으로 하였다. 분석결과 145m길이의 캐노피인 경우 50%정도의 개구율이 기류유동 패턴 및 환기효과면에서 가장 바람직하였다. 1.8km 터널내에서 20MW 화재발생시 종단구배는 풍속분포와 화재연 확산에 큰 영향을 미치며 제트팬$({\varnothing}1250)$ 4대를 가동한 경우 화재발생 후 5분 경과시 하류 40m지점 부근에서의 화재연 농도는 +2% 구배에서는 13% 감소, -2% 구배의 경우에는 20%정도 증가하며 또한 backlayering거리가 45m정도에 달한다. 직사각형 단면터널의 경우, 화재연 농도 및 풍속분포는 말굽형 터널과 비교하여 현저한 차이가 관찰되지 않는다. 3차선 터널에서는 이들 변수는 모두 감소하며 100초 경과시 50m 정도의 backlayering을 보이며 이후 서서히 감소한다. 곡선터널인 경우는 화재연의 확산이 느리며 100초 경과시 50m에 달하던 backlayering현상은 급격히 사라진다.