• KIEAE Journal
• /
• 제15권4호
• /
• pp.77-84
• /
• 2015

Purpose: In 2008, As the green growth policy was presented, Green Building is made any effort to propagation. In this paper, the respective technologies that are able to considerably reduce the energy demands for heating, cooling, hot-water, lighting and ventilation among the variety of technologies were selected. Method: Design factors such as (1) External insulation, (2) Triple glazing window, (3) LED lighting, (4) External venetian blind, (5) Geothermal and (6) Heat recovery ventilator were derived. In addition, energy saving effects in terms of energy demand, energy consumption and energy cost were investigated using EnergyPlus, building energy analysis tool. Result : The results were as follows. (1) It can be seen that high insulated triple glazing window, heat recovery ventilator and external insulation technology is excellent for energy demand. (2) Unlike energy demand, saving effect of energy consumption and energy cost was shown in order of Geothermal > Triple Window > Heat recovery Ventilation> Insulation> LED Lighting > EVB Blind.

• Membrane and Water Treatment
• /
• 제8권6호
• /
• pp.529-541
• /
• 2017

A multi-effect air gap membrane distillation (ME-AGMD) module for pesticide wastewater treatment is studied with internal heat recovery, sensible heat of brine recovery, number of stages and the use of fresh feed as cooling water in a single module is implemented in this study. A flat sheet polytetrafluroethylene (PTFE) membrane was used in the 4-stage ME-AGMD module. The maximum value of permeate flux could reach $38.62L/m^2h$ at feed -coolant water temperature difference about $52^{\circ}C$. The performance parameter of the module like, specific energy consumption and gain output ratio (GOR) was investigated for the module with and without heat recovery. Also, the module performance was characterized with respect to the separation efficiency of several important water quality parameters. The removal efficiency of the module was found to be >98.8% irrespective water quality parameters. During the experiment the membrane fouling was caused due to the deposition of the salt/crystal on the membrane surface. The membrane fouling was controlled by membrane module washing cycle 9 h and also by acidification of the feed water (pH=4) using 0.1M HCl solution.

• 한국기계가공학회지
• /
• 제16권1호
• /
• pp.58-62
• /
• 2017

In this paper, we studied the structural design for safety improvement of the winch mount of the armored recovery vehicle. From the finite element analysis using the safety factor of the original winch mount, the results determined that the safety factor was very low, namely 1.14 at $-15^{\circ}$ when towing the maximum force. For considering the usage and safety, the safety factor needs to increase to between 1.4 and 1.6. To improve the safety factor, a re-design, such as shape modification and strengthening the welded zone, was performed. After the improvement of the structural design, the safety factor of the improved mount was calculated at 1.78, an increase of about 56.1% from that of the original mount.

• 한국멀티미디어학회논문지
• /
• 제18권12호
• /
• pp.1492-1500
• /
• 2015

In recent crime scene, there is the captured crime scene video at least one. So video files recorded on storage media often provide important evidence. Criminals often attempt to destroy storage saved crime scene video. For this reason recovery of a damaged or deleted video file is important to resolve criminal cases in aspects of digital forensic. In the recent, there is a study to recover video file based on video frames, but it is very poor time efficiency when the connecting video frames. This paper proposed advanced frame-based recovery technique of a damaged video files using time information. We suggest a new connecting algorithm to connect video frames using recorded time information in front of video frame. We also evaluate performance in aspects of time and experiment result shows that proposed method improves performance.

• Nuclear Engineering and Technology
• /
• 제33권1호
• /
• pp.1-11
• /
• 2001

In contrast with conventional fieldbus researches which are focused merely on real-time performance, this study aims to evaluate the real-time performance of the communication system including fault-tolerant mechanisms Maintaining performance in presence of recoverable faults is very important in case that the communication network is applied to a highly reliable system such as next generation Nuclear. Power. Plant (NPP). If the tie characteristics meet the requirements of the system, the faults will be recovered by fieldbus recovery mechanisms and the system will be safe. If the time characteristics can not meet the requirements, the faults in the fieldbus can propagate to the system failure. In this study, for the purpose of investigating the time characteristics of fieldbus, the recoverable faults are classified and then the formulas that represent delays including recovery mechanisms are developed. In order to validate the proposed approach, we have developed a simulation model that represents the Korea Next Generation Reactor (KNGR) NSSS Process Control System (NPCS). The results of the simulation show us the reasonable delay characteristics of the fault cases with recovery mechanisms. Using the simulation results and the system requirements, we also can calculate the failure propagation probability from fieldbus to outer system.

• 한국기계가공학회지
• /
• 제15권2호
• /
• pp.46-50
• /
• 2016

When rotating the clutch drum in the power take-off (PTO) gear box of an armored recovery vehicle, lots of inner oil is drained through the adapter by centrifugal force. Therefore, a lack of lubrication is caused by inner oil loss, and the bearing is damaged by overheating. This study, therefore, aims to design an oil-controlling adapter by using shape alteration to prevent oil loss. Both the original and improved adapters were tested at 1,800rpm by using an operational test machine. When applying the original adapter to the gear box, the bearing was damaged by overheating, which was caused by the lack of lubrication. When applying the improved oil-controlling adapter, on the other hand, it prevented the loss of inner oil. Applying the improved adapter is expected to prevent the overheating caused by lack of lubrication.

• 대한금속재료학회지
• /
• 제49권11호
• /
• pp.874-881
• /
• 2011

The present study describes a new technique to extract the primary silicon from an Al-Si alloy melt using centrifugal force during its solidification. The primary silicon was separated from an Al-50 wt.%Si alloy by centrifugal force in the form of a foam, which facilitated subsequent acid leaching to extract the pure silicon due to its wide surface area. The foam recovery after centrifugal separation was decreased as centrifugal acceleration was increased. The final recovery after acid leaching became closer to the solid fraction of the alloy, which was calculated from the Al-Si binary phase diagram, with increasing centrifugal acceleration due to the effective removal of the attached Al on the foam. The purity of the primary silicon obtained by the centrifugal separation method was over 99.99%, with only aluminum being also present.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2001년도 The 6th International Symposium of East Asian Resources Recycling Technology
• /
• pp.421-426
• /
• 2001

The pneumatic classification and acidic leaching behaviors of phosphor sludge have been examined to establish the recycling system of rare earth components contained in waste fluorescent lamp. At first, separation characteristic of rare earth components and calcium phosphate in phosphor sludge was investigated by pneumatic classification. After pneumatic classification of phosphor sludge, rare earth components were leached in various acidic solutions and sodium hydroxide solution. For recovery of soluble component in leaching solution, rare earth components were separated as hydroxide and oxalate precipitations. The experimental results obtained are summarized as follows: (1) In classification process, rare earth components in phosphor sludge were concentrated to 29.3% from 13.3%, and its yield was 32.9%. (2) In leaching process, sulfuric acid solution was more effective one as a leaching solvent of rare earth component than other solutions. Y and Eu components in phosphor sludge were dissolved in sulfuric acid solution of 1.5 k㏖/㎥, and other rare earth components were rarely dissolved in leaching solution. Leaching degrees of Y and Eu were respectively 92% and 98% in the following optimum leaching conditions; sulfuric acid concentration is 1.5 k㏖/㎥ , leaching temperature 343 K, leaching time 3.6 ks and pulp concentration 30 kg/㎥. (3) Y and Eu components of phosphor sludge contained in waste fluorescent lamp were, effectively recovered by three processes of pneumatic classification, sulfuric acid leaching and oxalate precipitation methods. Their recovery was finally about 65 %, and its purity was 98.2%.

• Archives of Metallurgy and Materials
• /
• 제66권4호
• /
• pp.983-986
• /
• 2021

This study investigated the recovery behavior of valuable metals (Co, Ni, Cu and Mn) in spent lithium ion-batteries based on Al₂O₃-SiO₂-CaO-Fe₂O₃ slag system via DC submerged arc smelting process. The valuable metals were recovered by 93.9% at the 1250℃ for 30 min on the 20Al₂O₃-40SiO₂-20CaO-20Fe₂O₃ (mass%) slag system. From the analysis of the slag by Fourier-transform infrared spectroscopy, it was considered that Fe₂O₃ and Al₂O₃ acted as basic oxides to depolymerize SiO₄ and AlO₄ under the addition of critical 20 mass% Fe₂O₃ in 20Al₂O₃-40SiO₂-CaO-Fe₂O₃ (CaO + Fe₂O₃ = 40 mass%). In addition, it was observed that the addition of Fe₂O₃ ranging between 20 and 30 mass% lowers the melting point of the slag system.

• 한국항행학회논문지
• /
• 제11권4호
• /
• pp.479-484
• /
• 2007

본 논문은 FRA(Fault Recovery Agent)의 설계와 구축을 설명한다. FRA는 홈 네트워크 환경에서 멀티미디어 원격 교육을 위한 소프트웨어 오류를 복구하기에 적합한 에이전트이다. 분산 멀티미디어 시스템 견지에서 보면, QoS의 가장 중요한 범주는 시간성, 볼륨, 신뢰성이다. 본 논문에서는 결함 허용을 통해서 신뢰성을 향상시키는 방법에 대해서 기술한다. 본 논문은 규칙-기반 DEVS 모델링과 시뮬레이션 기법을 사용하면서 분산 멀티미디어 상에서의 오류 복구 시스템의 성능 분석을 설명한다. DEVS에서 하나의 시스템은 시간, 입력, 상태, 출력 및 함수들을 가지고 있다. 제시된 방법이 기존 방법에 비하여 오류 발생률과 작업 수행 시간에 있어서 더 효율적이다.