• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.21 no.4
• /
• pp.381-391
• /
• 2010

In this paper, a novel frequency reconfigurable active array antenna(RAA) system, which can be reconfigurable for three reconfigurable frequency bands, is proposed by using commercial RF MEMS switches. The MEMS switch shows excellent insertion loss, linearity, as well as isolation. So, the system performance degradation of the reconfigurable system by using MEMS switches can be minimized. The proposed frequency reconfigurable active antenna system is consisted with the noble frequency reconfigurable front-end amplifiers(RFA) with the simple reconfigurable impedance matching circuits(RMC), reconfigurable antenna elements(RAE), as well as a reconfiguration control board(RCB) for MEMS switch control. The proposed RAA system can be reconfigurable for three frequency bands, 850 MHz, 1.9 GHz, and 3.4 GHz, with $2{\times}2$ array of the RAE having broadband printed dipole antenna topology. The validity of the proposed RFA as well as RAA is also presented with the experimental results of the fabricated systems.

• Journal of electromagnetic engineering and science
• /
• v.16 no.4
• /
• pp.206-209
• /
• 2016

This letter proposes a reconfigurable directional coupler that uses a variable impedance mismatch reflector to achieve high isolation characteristics in the antenna front end. The reconfigurable coupler consists of a directional coupler and a single-pole four-throw (SP4T) switch with different load impedances as a variable load mismatch reflector. Selection of the load impedance by the reflector allows cancellation of the reflected signal due to antenna load mismatch and the leakage from the input to isolation port of the directional coupler, resulting in high isolation characteristics. The performance of the proposed architecture in separating the received (Rx) signal from the transmitted (Tx) signal in the antenna front end was verified by implementing and testing the reconfigurable coupler at 917 MHz for UHF radio-frequency identification (RFID) applications. The proposed reconfigurable directional coupler showed an improvement in the isolation characteristics of more than 20 dB at the operation frequency band.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.17 no.6 s.109
• /
• pp.556-561
• /
• 2006

In this paper, a frequency reconfigurable slot antenna which has a bandwidth-enhanced characteristic is proposed. The proposed antenna consists of two parts; the wide slot and the narrow slot, to increase the bandwidth of the antenna and have the frequency reconfigurable characteristic. The wide slot has triangular shape and makes the bandwidth increased, and the narrow slot can mount PIN diodes. By changing on/off state of PIN diodes, the total length of the slot is changed. From this characteristic, the proposed antenna can finally control the center frequency and minimize variation of the impedance matching.

• Journal of electromagnetic engineering and science
• /
• v.7 no.4
• /
• pp.154-160
• /
• 2007

A reconfigurable multi-band mixer for the SDR system is proposed. The proposed reconfigurable mixer is operated between $850\;MHz{\sim}2\;GHz$, which includes all commercial mobile communication service. Because the varactor diodes are used to select a specific frequency and to adjust the impedance characteristic of the selected frequency band, the proposed reconfigurable mixer can be achieved to similar performance across all of the tuning range. In addition, the designed reconfigurable mixer is applicable for the SDR system since it has a single signal path for the multi-band signals and wide band tuning range.

• Transactions of Materials Processing
• /
• v.23 no.2
• /
• pp.103-109
• /
• 2014

Flexibly-reconfigurable roll forming (FRRF), which is a sheet forming process for multi-curved sheet metal, may solve both the economic and technical problems incurred in using a conventional die forming process. In the FRRF process, the multi-curved sheet metal is formed by different strain distributions on the sheet metal, and the reconfigurable rollers are used as tools during the forming. Therefore, a thorough investigation focused on the reconfigurable rollers is required for the realization of the FRRF process prior to the fabrication of FRRF machine. In the current study, a series of finite element simulations were conducted to study the load distributions experienced by the reconfigurable roller. In order to verify the shape design variables, the effect of the metal thickness on the curvatures of sheet is also presented.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.41 no.7
• /
• pp.775-782
• /
• 2016

In this paper, we presented the paper-based reconfigurable frequency selective surface(FSS) for transmitting or blocking the wireless LAN signal in indoor environments. The proposed reconfigurable FSS are designed on coated paper using a printing of conductive ink and conductive adhesive for PIN diode, which provides ON/OFF of the reconfigurable FSS for passing or blocking the 5GHz signal. The reconfigurable FSS attached on the wall can pass or block the incident wireless signal as the received signal strength in indoor. To provide the validity of the proposed FSS, we fabricated the reconfigurable FSS on the paper and confirmed the very similar results between simulations and measurements. From the measured results of the proposed spectrum control system, we know that the proposed reconfigurable FSS can block about 20dB at 5.745GHz~5.805GHz.

• Transactions of Materials Processing
• /
• v.25 no.1
• /
• pp.12-20
• /
• 2016

Press machines and dies are commonly used for 3D curved sheet forming. Using conventional die forming can cause economic problems since various modifications of the die shape are required depending on the product shape. Various types of flexible forming such as multi-point dieless forming (MDF), flexible incremental roll forming have been developed to improve the needed process flexibility. Although MDF can reduce the production cost using reconfigurable dies, it still has significant material loss. Drawbacks such as wrinkling, dimpling, and forming errors can also occur despite continuous investigations to mitigate these defects. A novel sheet forming process for 3D curved surfaces, a flexibly-reconfigurable roll forming (FRRF), has been recently proposed to overcome the economic and technical limitations of current practice. FRRF has no limitation on blank size in the longitudinal direction, and also minimizes or eliminates forming defects such as wrinkling and dimpling. Feasibility studies of FRRF have been conducted using FE simulations for multi-curved shapes and various sheet thicknesses. Therefore, the fabrication of a FRRF apparatus is required for any follow-up studies. In the current study, experiments with reconfigurable rollers were conducted using a simple design pre-FRRF apparatus prior to fabricating the full size FRRF apparatus. There are three candidates for the reconfigurable roller: a bar-type shaft, a flexible shaft, a ground flexible shaft. Among these candidates, the suitable reconfigurable roller for FRRF is determined through various forming tests.

• Journal of Electrical Engineering and information Science
• /
• v.3 no.3
• /
• pp.281-285
• /
• 1998

Consider the two-dimensional sorted-set convex hull problem: Given N points in a plane sorted by the x coordinates, compute the convex hull of the points. We propose an O(logNlog logN)-time algorithm that solves the sorted-set convex hull problem on an N\ulcorner\ulcorner${\times}$N\ulcorner\ulcorner reconfigurable mesh. The best known algorithm for the problem on an N\ulcorner\ulcorner${\times}$N\ulcorner\ulcorner reconfigurable mesh takes O(log\ulcornerN) time. Although there is a constant-time algorithm on an N${\times}$N reconfigurable mesh for general two-dimensional convex hull problem, the general convex hull problem requires Θ(N\ulcorner\ulcorner) time on an N\ulcorner\ulcorner${\times}$N\ulcorner\ulcorner reconfigurable mesh due to bandwidth constraints.

• Journal of Institute of Control, Robotics and Systems
• /
• v.13 no.5
• /
• pp.422-428
• /
• 2007

This paper presents a neural network based adaptive control approach to a reconfigurable flight control law that keeps handling qualities in the presence of faults or failures to the control surfaces of an aircraft. This approach removes the need for system identification for control reallocation after a failure and the need for an accurate aerodynamic database for flight control design, thereby reducing the cost and time required to develope a reconfigurable flight controller. Neural networks address the problem caused by uncertainties in modeling an aircraft and pseudo control hedging deals with the nonlinearity in actuators and the reconfiguration of a flight controller. The effect of the reconfigurable flight control law is illustrated in results of a nonlinear simulation of an unmanned aerial vehicle Durumi-II.

• Proceedings of the IEEK Conference
• /
• 2002.07b
• /
• pp.1276-1279
• /
• 2002

In order to satisfy the requirement for various applications in an electronic device, many dynamically reconfigurable systems such as FPGAs have been used recently. This paper presents a pipelined scheduling for dynamically reconfigurable systems based on FPGAs. For reconfigurable systems conventional schedulings have reduced processing time by minimizing the number of reconfigurations. However, they are not effective enough for applications including many iterative processes such as digital signal processing. Our approach has been able to increase throughput of iterative applications on dynamically reconfigurable systems by using pipelined scheduling.