• Structural Engineering and Mechanics
• /
• v.82 no.1
• /
• pp.1-16
• /
• 2022

This work elaborately investigates the influences of the guideway geometry parameters and track irregularity on the dynamic performances of the suspended monorail vehicle-guideway system (SMVGS). Firstly, a spatial dynamic analysis model of the SMVGS is established by adopting ANSYS parameter design language. Then, the dynamic interaction between a vehicle with maximum design load and guideway is investigated by numerical simulation and field tests, revealing the vehicle-guideway dynamic features. Subsequently, the influences of the guideway geometry parameters and track irregularity on the dynamic performances of the SMVGS are analyzed and discussed in detail, and the reasonable ranges of several key geometry parameters of the guideway are also obtained. Results show that the vehicle-guideway dynamic responses change nonlinearly with an increase of the guideway span, and especially the guideway dynamic performances can be effectively improved by reducing the guideway span; based on a comprehensive consideration of all performance indices of the SMVGS, the deflection-span ratio of the suspended monorail guideway is finally recommended to be 1/1054~1/868. The train load could cause a large bending deformation of the pier, which would intensify the car-body lateral displacement and decrease the vehicle riding comfort; to well limit the bending deformation of the pier, its cross-section dimension is suggested to be more than 0.8 m×0.8 m. The addition of the track irregularity amplitude has small influences on the displacements and stress of the guideway; however, it would significantly increase the vehicle-guideway vibrations and rate of load reduction of the driving tyre.

• Journal of the Korea Convergence Society
• /
• v.12 no.11
• /
• pp.347-357
• /
• 2021

Since the outbreak of Covid-19, many countries have tried to defense Covid-19 to protect their people and as an influential and reliable policy as of now, they have recommended vaccinating. Thus, this research explored what influences the intention to vaccinate against Covid-19 with three health locus of control from multi-dimension health locus of control (MHLC) and perceived susceptibility and severity from health belief model (HBM) through PLS path modeling. Consequently, chance locus of control (CHLC) influence indirectly intention to vaccinate against Covid-19 mediating with susceptibility perception. It implies that the more fatalistic people attitude toward Covid-19, the more susceptible they perceived to the disease, and then, the stronger intention to vaccinate they would have. Thus, the health promotion authorities should motivate to activate people's susceptibility perception toward the disease through utilizing a variety of policies and consider that the fatalistic tendency toward the disease of people could play an antecedent role in the process.

• International conference on construction engineering and project management
• /
• 2013.01a
• /
• pp.634-639
• /
• 2013

The aim of the study is to develop the 3D visualization of Building Information Model and integrated 4D model for optimization of resources in the construction project. This study discuss the process of methodology and creation of 4D model of the project and simulate it to monitor the workflow at the site. Different stages of the construction process and activities are generated by using Revit and MS Project. MS project has been used for creation of the schedules and these are linked with the Revit for 3D modeling. The time used as the fourth dimension and 4D model created by using Navisworks Time liner software. Narges shopping center is presented as a case study to realize the actual uses and benefits of Building Information Model (BIM). Narges shopping mall is located in Tehran, Iran. As a part of Hekmat master plan, Narges shopping center is an 11 stores building with a total area of 30000 Sq.m. This shopping and entertainment center is comprised of 150 retails and two multi-use public halls with a capacity of 400 persons each and underground parking with total 400 parking space. The main purpose of architecture was to create an urban public center along with its revolving, spiral like form and an ever changing continuous façade by means of different colors, materials, which is in harmony with the other building of the master plan. The approximate cost of the project is $17 million and duration of the project schedule is 30 months. The developed Building Information Model enabled us to identify the potential collisions or clashes between various structural and architectural systems. 4D model has been used for limiting the interaction between subcontractors installing the different systems so rework could be avoided and productivity maximized. It is also observed that the utility of BIM for construction stimulation and clash detection is the best suitable method. Clash detection before the implementation of work is highly recommended to avoid rework.

• The Journal of Korean Academy of Prosthodontics
• /
• v.47 no.1
• /
• pp.29-38
• /
• 2009

Statement of problem: A casting connection technique is widely used for repair, correction and addition to base metal framework. However, a casting connection technique may increase the risk of failure in clinical situations when high stresses exist. Purpose: The purpose of this study was to investigate the mechanical retentive groove design comparatively to increase the joint strength by using the three-dimensional finite element analysis model of a 3-unit fixed partial denture. Material and methods: Ten finite element models were constructed. (Model A: One retentive groove, Model B: Two retentive grooves, Model C: Three retentive grooves, Model D: Four retentive grooves, Model E: One horizontal groove and two vertical grooves, Model F: Two horizontal grooves and one vertical groove, Model G: One groove with the enlarged dimension, Model H: Two grooves with the enlarged dimension, Model I: One groove with the increased height, Model J: One groove with the increased width of base). The vertical force was applied to the mesial and the distal fossa to the casting connection of mandibular first molar. Results: The main factors, affecting joint strength of casting connection were both the retention between the primary cast and the secondary cast and the thickness of the primary cast remaining after preparing retentive groove. The increase of retentive force, according to the numbers and the dimension of retentive groove had an effect on distributing stress. However, in some cases, the increase of retentive force resulted in the increase of stress by reducing thickness of the primary cast in the connection area. Conclusion: The design of retentive groove that limits number of retentive groove for metal thickness and increases the depth of retentive groove for retention is highly recommended.

• Journal of the Korea Concrete Institute
• /
• v.19 no.6
• /
• pp.773-783
• /
• 2007

A simple unbonded-type shear strengthening technique for reinforced concrete beams using wire rope units is developed. Six two-span continuous T-beams externally strengthened with wire rope units and an unstrengthened control beam were tested. The main variables investigated were the amount and prestressing force of wire rope units. All specimens had the same geometrical dimension and arrangement of internal reinforcement. Influence of the distribution of vertical stresses in beam web owing to the prestressing force of wire rope units on the diagonal shear cracking load and the ultimate shear capacity of beams tested is presented. Based on the current study, it can be concluded that the amount and initial prestress of wire rope should be limited to be above 2.5 times the minimum shear reinforcement ratio specified in ACI 318-05 and below 0.6 times its own tensile strength, respectively, to ensure the enhancement of shear capacity and ductile failure mode of the strengthened beams. A numerical analysis based on the upper-bound theorem is developed to assess the shear capacity of continuous T-beams strengthened with wire rope units. From the comparisons of measured and predicted shear capacities, a better agreement is achieved in the proposed numerical analysis than in empirical equations recommended by ACI 318-05.

• Analytical Science and Technology
• /
• v.9 no.3
• /
• pp.262-269
• /
• 1996

The muiltiwire proportional counter for the measurement of low-level and environmental $\alpha$ particles emitting nuclides was developed. External dimension of the devloped multiwire proportional counter is $350{\times}290{\times}30mm$ and the sensitivity area is $250{\times}200mm$. The wall material of the detector was selected the stainless steel to prevent the deformation by external impact and to obtain minimum background. The anode and cathode wires were used the stainless steel material of diameter $50{\mu}m$. The spacing of each wires are 10.0mm, 5.0mm and the numbers of total wire are 21, 42 lines, respectively. The multiwire proportional counter was designed that the measurement source is placed within the detector to prevent the wall absorption effect and the efficiency variation by various source heights. The characteristics of the developed detector have been investigated to obtain the plateau, operating voltage, background, counting efficiency, position sensitivity and energy resolution etc. For the $^{241}Am$ nuclide, the calculated LLD(Lower Limit of Detection) is 5.0mBq/L which is lower than 40mBq/L of recommended LLD value by ISO(International Organization for Standardization).

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.11 no.10
• /
• pp.3794-3801
• /
• 2010

This study evaluated the linear dimensional changes with the factor of time and thickness using of three commercially available tissue conditioners (Coe-Comport, Visco-Gel, Soft-Liner). The thickness of materials were changed (1.5mm, 3.0mm) and the percentage changes in dimension were measured at 1h(baseline), 12h, 24h, 3 days and 7days after specimen preparation. The obtained data were analyzed by ANOVA with the SAS/PC statistical package. From the results, large differences appear between the various tissue conditioners. The results suggested that the period recommended for forming functional impression would be 36h to 3days after insertion in the mouth. Depending on the type of tissue conditioner over time, as there were significant differences in the elastic change(p<0.05). Tissue conditioner of the 1.5mm, 3.0mm thickness were significantly different by the dimensional stability(p<0.05). Elastic deformation of the ideal itself, and resilient when compared only the look, Visco-Gel 3.0mm group, stability was the most stable volume. In addition, it is important to select tissue conditioners suitable for functional impression because of the wide range of dimensional stability among the materials.

• Journal of KIISE:Computing Practices and Letters
• /
• v.10 no.5
• /
• pp.406-418
• /
• 2004

Last days, various kinds of applications and system were individually introduced into specific groups or enterprises by different objective without considering interoperability among those. However, the environment for data processing is changing rapidly in these days. And now the necessity is growing to integrate and couple applications and system in the process dimension for more flexible and quicker data processing on these application programs and system. When integrating these application programs or system, an integration based on XML is recommended as it is one of good methods which will the additional cost and satisfy the requirements of the integration. This is because the XML is not only device-independent data type which can be used any platform, but also it uses XSLT, the document conversion standard established by W3C, which allows easy data conversion from one to another type on occasion of demands. This paper studies a design and implementation of system to convert XML structure. This system shows the structure of source- side providing data and destination-side processing data with using XML schema that defines structural information of a XML document. And this system defines the structure relationship of desired form as mapping structural information and data. This system creates the XSLT document that defines conversion rule between two structures based information which is defined. The XSLT document which is created as described above will convert data to be appropriate to the structure of the destination- side. By implementing this system, it is able to apply a document into various kinds of structure without considering specific system or platform and it is able to construct XSLT document to which meaning of desired form can be given. This paper aims to offer a process conversion between documents and to improve interoperability and scalability, so that we can contribute to build XML document processing environment

• The Journal of the Korea Contents Association
• /
• v.14 no.1
• /
• pp.488-504
• /
• 2014

The purpose of this study was to identify whether environmental evidence and experiences respectively could affect brand attitude in Korean restaurant. Also, this study investigated a moderating effect of brand reputation in the causal relationship between environmental evidence and brand attitude and, between experiences and brand attitude. Questionnaires were given to a sample of customers who visited branches of H or B Korean restaurant brand which ranked within 20th in sales volume among Korean restaurant brands. A total of 353 questionnaires were analyzed with hierarchical regression analysis using SPSS/PC+. There were four major empirical research findings. Firstly, among components of environmental evidence, space, aesthetics, cleanliness and pleasance affected brand attitude. Secondly, all components of experiences, act, relate, think and feel affected brand attitude. Thirdly, brand reputation had a moderating role in the causal relationship between aesthetics dimension and brand attitude, but space, cleanliness, convenience and pleasance dimensions did not have a moderating role of brand reputation to the relationship of brand attitude. Fourth, brand reputation had a moderating role in the causal relationship between act and brand attitude, but relate, think and feel didn't have a moderating role of brand reputation to the relationship of brand attitude. Based on these findings, marketers of Korean restaurants were recommended to strengthen environmental evidence and experiences. Also, they are advised to strengthen brand reputation with use of marketing.

• The Journal of the Korea Contents Association
• /
• v.14 no.5
• /
• pp.211-223
• /
• 2014

The aim of this study was to identify the levels of family members' burden and to describe factors influencing on famiCX*//8ly caregiver's burden when they are planned to transfer to general ward from the intensive care units (ICU). A descriptive survey was used with a convenience sampling of 101 family members of ICU patients at S university hospital in C city, Korea from August to November, 2010. The data were analyzed with SPSS 18.0 program. The level of object burden in family members had statistically significant differences with level of consciousness, number of patients' monitoring devices, and tracheostomy tube. The level of subject burden had statistically significant differences according to patients' gender, patients' education level, and relationship with patients. Transfer anxiety was showed statistically positive correlation with objective and subjective burden. We found transfer anxiety was statistically significant predictor of family caregiver's objective burden with explanatory power 12.7%. Family members' subjective burden were statistically influenced by patients' gender and transfer anxiety. These factors explained 23.8% out of total variance of family members' objective burden. The structured individualized method of transfer is recommended with further research of ICU families to further examine the dimension of transfer anxiety and how it affects family members' burden and patient outcomes.