• 한국자동차공학회논문집
• /
• 제13권2호
• /
• pp.65-71
• /
• 2005

Our environment is faced with serious problems related to the air pollution from automobiles in these days. In particular, the exhaust emissions of diesel engine are recognized main cause which influenced environment strong. In this study, the potential possibility of biodiesel fuel was investigated as an alternative fuel for a naturally aspirated D.I. diesel engine. The smoke emission of biodiesel fuel was reduced remarkably in com parison with diesel fuel, that is, it was reduced approximately 48.5% at 2500rpm, full load. But, power, torque and brake specific energy consumption didn't have no large differences. But, $NO_X$ emission of biodiesel fuel was increased com pared with commercial diesel fuel. Also, the effects of exhaust gas recirculation(EGR) on the characteristics of $NO_X$ emission has been investigated. It was found that simultaneous reduction of smoke and $NO_X$ was achieved with biodiesel fuel(20vol-%) and cooled EGR method($5{\sim}15%$).

• 한국자동차공학회논문집
• /
• 제22권7호
• /
• pp.90-97
• /
• 2014

The effects of high pressure and low pressure exhaust gas recirculation (HP/LP EGR) portion on diesel engine combustion and emissions characteristics were investigated in a 2.2 L passenger-car diesel engine. The po3rtion of HP/LP EGR was varied from 0 to 1 while fixing the mass flow rate of fresh air. The intake manifold temperature was lowered with the increasing of the portion of LP EGR, which led to the retardation of heat release by pilot injection. The lowered intake manifold temperature also resulted in low nitrogen oxide (NOx) emissions due to decreased in-cylinder temperature and prolonged ignition delay, however, the carbon monoxide (CO) emission showed opposite trend to NOx emissions. The brake specific fuel consumption (BSFC) was decreased as the portion of LP EGR increased due to lowered exhaust manifold pressure by wider open of turbocharger vane. Consequently, the trade-off relationship between NOx and BSFC could be improved by increasing the LP EGR portion.

• 한국추진공학회지
• /
• 제3권2호
• /
• pp.18-24
• /
• 1999

액체 램제트 연소기는 흡입공기와 분무, 혼합 그리고 이에 따른 연소 등 일련의 과정에 따라 다수의 복잡한 현상들이 상호 밀접하게 관련되어 있으며, 이러한 반응 및 비반응 유동 특성을 파악하기 위해서 2차원 및 3차원 연소기 형상에 대해서 수치적 실험을 수행하였다 격자구성은 연소기에 공기를 공급하고 연료를 분무하는 공기 유입관 영역과 연소실 영역, 그리고 출구 대기 영역으로 나누어 격자를 생성시켰다. 비반응 유동해석을 통해서 연소실내의 선회영역 유동특성은 2차원과 3차원이 크게 차이가 남을 알 수 있었다. 반응 유동 해석에서는 분무 모델의 적용 유무에 따라 연소 형태가 크게 변화하였다. 연료의 분사위치를 유입관의 위쪽에 준 경우와 아래쪽에 준 두 가지 경우를 비교하였으며, 유입관의 아래쪽에 연료의 분사위치를 준 경우가 연소의 안정화에 필요한 재순환 영역으로의 연료의 유입이 잘 되어 유입관 위쪽에 연료를 분사시키는 것보다 좋은 분사위치임을 알 수 있었다.

• 한국안전학회지
• /
• 제9권1호
• /
• pp.100-109
• /
• 1994

In this study, it is investigated that the possibility of the numerical simulation for the incineration of the hazardous material, crbon tetrachloride($CCl_4$). A 3-dimensional numerical technology is applied for turbulent reacting flows of the full-scale Dow Chemical incinerator. The calculations are made by a CRAY-2S, super computer. The major parameters considered in this study are kiln revolution rate (rpm), filling ratio of the solid waste(f), burner Injection velocity and angle, and turbulent air jets for swirl. And the employed turbulent reaction model is the eddy break-up model which is a kind of fast chemistry model assuming general equilibrium and used for a premixed flame. The calculated flow fields are presented and discussed. 1) The presence of turbulent air nozzles for swirl gives rise to visible increase of the convective motion over the region of the solid waste. This implies the possibility to enhance the mixing of the waste with the surrounding all and thereby to reduce thermal and species stratification, which were reported in a large rotary kiln operation. 2) Considering that the location of the recirculation region has a strong relation with the heating rate of the solid waste, the control of the recirculation region by the burner injection angle Is quite desirable in the sense of the flexible design of the rotary kiln incinerator for a carbon tetrachloride. 3) Finally, it is found that the eddy break-up model Is not suitable for carbon tetrachloride($CCl_4$) because this model is not incorporated the flame inhibition trend due to the presence $CCl_4$compound.

• 한국자동차공학회논문집
• /
• 제22권1호
• /
• pp.148-156
• /
• 2014

The objective of this study is to compare NOx emissions from light duty diesel vehicles measured from on-road tests that conducted under various driving routes and seasonal conditions. We measured real-driving NOx emissions using PEMS, portable emissions measurement system, under the urban, rural and motorway road traffic conditions. On-road tests were repeated at summer, fall and winter season. The accumulated driving distance is more than 1,200 km per each vehicle. Route average NOx emission factors were compared among nine route-season combinations. The emission characteristics of each combinations were investigated using time series mass emission rates and vehicle operation-based emission rates and activities, which is based on U.S. EPA's MOVES model. Most concerned route-season combination is "urban road condition at summer", which shows two to eleven times higher NOx emissions than other combinations. The emission rates and activities under low speed operating conditions should be managed in order to reduce urban-summer NOx. From a NOx control strategy perspective, the exhaust gas recirculation, EGR, is observed to be properly operated under wide range of vehicle driving conditions in Euro-5 vehicles, even if the air conditioner turns on. In high power demanding conditions, the effect of overspeeding could be more critical than that of air conditioner activation.

• 대한기계학회논문집A
• /
• 제39권2호
• /
• pp.203-209
• /
• 2015

건설기계 산업에서 배기 및 연비 규제를 만족하기 위하여 엔진 시스템이 점차 전자제어화 되고 있으며, 이를 제어하기 위한 EMS(Engine Management System)의 복잡도 또한 증가하고 있다. 본 연구에서는 EMS function 개발 시, 비용 및 개발기간의 단축을 위한 HiLS(Hardware in the Loop Simulation) 시스템을 개발하였다. HiLS 에 내장된 엔진 모델은 크게 Air, Fuel, Torque 및 동력계 모델로 구성되어있고 실시간 엔진 모사를 위하여 Mean value modeling 방법을 적용하였다. 이 연구를 통하여 개발한 HiLS 시스템은 EGR(Exhaust Gas Recirculation) 시스템과 Turbocharger 가 장착된 건설기계용 디젤엔진을 이용하여 정확성을 검증하였고, 테스트 결과 실 엔진 대비 90% 이상의 정확도를 얻었다.

• 대한기계학회논문집B
• /
• 제37권9호
• /
• pp.847-854
• /
• 2013

본 연구는 환형 노즐 이젝터를 이용하여 수평방향 폭기공정의 혼합유동 및 산소전달 특성에 대한 실험적 연구를 목표로 한다. 실험변수는 이젝터 피치와 가압수 유량이며, 측정된 유량과 압력을 이용하여 유량비, 수두비 및 효율을 계산하였다. 이적터에서 분출된 혼합유동의 가시화를 통해 정성적 거동을 고찰하였으며, 용존산소량을 측정하여 총괄 산소전달계수를 도출하였다. 이젝터에서 분출된 혼합유동은 가압수의 운동량과 유입된 공기기포의 미립화에 따라 부력분류 또는 수평분류의 거동을 나타내었다. 기포의 크기에 기인하는 부력과 가압수의 운동량에 지배되는 혼합유동의 도달거리는 가압수와 공기기포의 접촉 면적 및 시간에 크게 영향을 미치기 때문에 산소전달률의 중요한 변수임을 유추할 수 있다.

• 유기물자원화
• /
• 제7권2호
• /
• pp.93-104
• /
• 1999

본 연구는 기존의 소멸화장치를 개선하여 에너지절감과 동시에 탈취효과를 극대화시키면서 유기물의 분해능력을 극대화시키는 장치를 개발하기 위하여 실시되었다. 기존의 장치와 비교하여 3차에 걸친 열교환을 통하여 백금촉매탑에서 발생하는 폐열을 회수하여 이용하게 하였으며, 배기가스의 65%정도를 재순환하게 하였다. 또한 장치전체에 대해서는 감압을 유지하게 하여 수분의 증발을 원활하게 하였다. 미생물제재에 의하여 반응을 안정적으로 유지하는 것이 가능했으며, 또한 분해매체제는 기존의 처리용량의 20배용적을 사용했으나, 본장치에서는 15배용적에 있어서도 미생물활성화가 가능하며, 호기성분위기를 효율적을 유지하는 것이 가능했다. 배기가스의 내부순환을 시스템을 사용함에 따라 얻어지는 효과에 대하여 검토한 결과, 내부의 악취물질인 암모니아가스농도를 감소시키는 것이 가능했으며, 탈취탑으로 유입되는 배기가스가 경감됨에 따라 전력비가1/3선으로 절감되는 효과가 확인되었다. 이러한 내순환에 따라 최적공기량은 100kg처리용량에 대하여 $0.44m^3$로, 이 공기량의 변화에 따라 전력비가 비례하여 변화하는 현상이 확인되었다.

• 설비공학논문집
• /
• 제22권4호
• /
• pp.225-233
• /
• 2010

We performed 3 dimensional numerical study on the improvement of the airflow deflection in the cleanroom of Class 1000, which is presently operated for the manufacturing process in Korea. The Deflection angle and the non-uniformity were investigated to analyze the airflow characteristics and the performance of cleanroom with variations of the cleanroom occupancy state, the filters' arrangement, and the floor return air system. From the numerical results, we found out that the airflow pattern of the cleanroom is more unidirectional and stable in the condition of at-rest than in the condition of as~built. It is due to that the equipments installed in the cleanroom play a role like partitions, which prevent the airflow from inclining toward the recirculation air duct. And it is needed to arrange the filter units parallel to the equipments array without a gap between them for maintaining the unidirectional airflow pattern. Finally, we knew that it is very important to install the partition like the eyelid above the equipment to keep the unidirectional airflow around the equipments and remove the contaminants quickly.

• Journal of Mechanical Science and Technology
• /
• 제20권12호
• /
• pp.2284-2291
• /
• 2006

The present study investigates gas residence time and mixing characteristics for various swirl numbers generated by injection of secondary air into a lab-scale cylindrical combustor. Fine dust particles and butane gas were injected into the test chamber to study the gas residence time and mixing characteristics, respectively. The mixing characteristics were evaluated by standard deviation value of trace gas concentration at different measurement points. The measurement points were located 25 mm above the secondary air injection position. The trace gas concentration was detected by a gas analyzer. The gas residence time was estimated by measuring the temporal pressure difference across a filter media where the particles were captured. The swirl number of 20 for secondary air injection angle of 5$^{\circ}$ gave the best condition: long gas residence time and good mixing performance. Numerical calculations were also carried out to study the physical meanings of the experimental results, which showed good agreement with numerical results.