• 한국소음진동공학회논문집
• /
• 제14권1호
• /
• pp.24-31
• /
• 2004

Recently, as the marine compressor power is increased, vibration problems on the marine vessel with V/W type reciprocating compressor have been occurred. A research on the balancing of marine V/W type reciprocating compressor has hardly been reported though a number of researches on the balancing of rotating machinery have been conducted. As a V/W type compressor has high capacity with long stroke, compact size and high center of gravity, It is easy to have a vibration problem by a little bit unbalanced force and moment. In this study, calculation methods for balance weight of the V/W type reciprocating compressors, which have different piston weight and asymmetry structure, are formulated. And their reliability were verified by comparing calculated balance weight with the experimental results of the real marine V/W type reciprocating compressors.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2008년도 추계학술대회A
• /
• pp.932-937
• /
• 2008

The pulsation of a reciprocating type hydrogen compressor is occurred from the mechanism and this pulsation makes much noise and vibration. To reduce this pulsation, snubber is usually installed on that. To maintain the efficiency in the reciprocating type hydrogen compressor, the pulsation and vibration should be reduced. so it is necessary to research about the characteristic of pulsation and vibration. Therefore in this paper, the vibration characteristic of the snubber is analyzed in the base of optimized modeling condition through the flowing analysis of existing snubber. The prototype of reciprocating type hydrogen compressor is analyzed with numerical analysis. And making sure the present condition of hydrogen compressor through measurement of vibration and noise, and then it is established that the vibration characteristic data base on numerical analysis which will be develope.

• 설비공학논문집
• /
• 제24권2호
• /
• pp.164-173
• /
• 2012

To study the applicability of a scroll type compressor to small capacity refrigerators, a R600a scroll compressor with algebraic scroll wrap has been designed. Its size and performance have been compared to a reciprocating type of the same displacement volume. By employing scroll wrap based on algebraic curve, high compression ratio can be accomplished without increasing the wrap angle much so that compact scroll may be obtained. Compared to a reciprocating one, the designed scroll compressor has diameter and height reduced by about 50% and 80%, respectively. By numerical simulation, it has been estimated that the scroll compressor provides 38.6% more cooling capacity than reciprocating type with 8.9% more power consumption, resulting in 27.3% increase in COP for ASHRAE low back pressure condition. With increasing the operating pressure ratio from 9.5 to 15.3, the overall compressor efficiency of the scroll compressor decreases from 72.6% to 65.2%, while that of the reciprocating compressor increases from 55.7% to 59.8%.

• 한국마린엔지니어링학회:학술대회논문집
• /
• 한국마린엔지니어링학회 2006년도 전기학술대회논문집
• /
• pp.35-36
• /
• 2006

This study is mainly concerned with vibration control of L-type reciprocating air compressor by a dynamic vibration absorber. The dynamic vibration absorber of reciprocating air compressor was designed for constant revolution running condition. For the review, Vibration test was conducted for the performance appraisal of installed dynamic vibration absorber in the reciprocating air compressor. As a result of the test, the performance of dynamic vibration absorber was satisfactory.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2007년도 춘계학술대회A
• /
• pp.1020-1025
• /
• 2007

The reciprocating type hydrogen compressor is for high pressure and volume. However this type compressor makes pulsation caused by mechanical characteristic. This type compressor also makes noise and vibration that cause negative effect to machine and working condition. Therefore, diagnosis and countermeasure are needed to decrease vibration for safety on hydrogen compressor. therefore in this paper, the numerical analysis and vibration measurement is conducted in order to investigate vibration characteristic and to evaluation vibration condition, Respectively

• Tribology and Lubricants
• /
• 제29권2호
• /
• pp.105-110
• /
• 2013

Refrigeration and air-conditioning compressors used in home appliances, including refrigerators and air conditioners, are typically hermetic-type reciprocating compressors. Because the shell is sealed by welding, it should be designed to have a semi-permanent life. The energy consumption of a hermetic-type reciprocating compressor is low, but because it operates continuously to maintain a constant temperature inside the refrigerator, it has a certain base load. In this type of compressor, the driving motor operates at a high speed (about 3,000 - 3,600 rpm), which causes valve damage, friction, wear, and high-frequency noise. Many studies have been conducted to solve these problems. To enhance the reliability and efficiency of the reciprocating compressor, the design conditions and operating environment of journal bearings should be considered. Dynamic behavior analysis should be carried out in terms of the discharge pressure. The results showed that the load (discharge pressure) increases in the forward lookup zone and decreases in the backward lookup zone. When the revolution speed is increased, the maximum load decreases in the region where the maximum load operates.

• Journal of Advanced Marine Engineering and Technology
• /
• 제32권8호
• /
• pp.1116-1122
• /
• 2008

The reciprocating type hydrogen compressor has a pulsation due to the reciprocative characteristics which results in noise and vibration. Snubber is installed for the relaxation of pulsation, but it causes reduction of compressor efficiency because of pressure loss. Five types of snubber were modeled for the numerical investigation of the effect of the relative position of inlet and outlet and buffer angle on the pulsation amplitude and pressure loss. MSC/NASTRAN is used as a numerical tool to identify the vibration characteristic of each type. Frequency responses in forced vibration mode are compared for various cases and buffer angles.

• 한국안전학회지
• /
• 제26권4호
• /
• pp.20-26
• /
• 2011

This paper is to investigate noise source for reciprocating type air compressors. The reciprocating type air compressors are widely used in the small and medium sized enterprise and many employees are affected and irritated by their noise during working. The investigation and analysis of the noise source were made according to the ISO 1680/1 and MIL-STD 7410-1 and noise evaluation of each part of compressors was made. Noise emitted from the intake and exhaust valve and the air receiver tank were dominant compared with those from other parts of compressor. Noise from the motor and the revolution of crank mechanism was negligible relatively with the noise sources as mentioned above.

• 융복합기술연구소 논문집
• /
• 제2권2호
• /
• pp.49-54
• /
• 2012

These conventional reciprocating compressor(reciprocating type compressor) or household refrigerators and car air conditioning rotary compressor, rotary compressor, has been used by a reciprocating piston torque variability and the deepening of the vibration problem, the suction valve and discharge valvein this study, as a result of the losses in the current use of the scroll compressor, scroll compressor with the features of low noise, high efficiency, small size, light weight, has increased. fixed Scroll(fixed scroll) scroll compressor with orbiting scroll (rotating scroll) vibration experiments were performed in order to identify the vibration characteristics of the structure of the Analysis was performed using the commercial finite element program(ANSYS) for the sake of comparison, the experimental results using a finite element model of research about the natural vibration characteristics due to a material change.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2007년도 추계학술대회논문집
• /
• pp.53-56
• /
• 2007

The reciprocating type hydrogen compressor is occurred by the pulsation from the mechanism and this pulsation is make much noise and vibration. Therefor snubber is installed for pulsation decreasing. The five type snubber models were designed for increasing pulsation amplitude reduction and decreasing pressure loss in snubber considering output pipe location as design value. And the pressure flued analysis is carried by CFD. In this paper, each type snubber according CFD result are analyzed by the MSC/NASTRAN to identify the vibration characteristic of each type. The vibration results are compared with CFD results.