• Proceedings of the Optical Society of Korea Conference
• /
• 2002.11a
• /
• pp.184-185
• /
• 2002

We discussed the main issues of 10GHz Receiver packaging. High frequency structure simulations and circuit simulations for TO-CANs led to a new design for 10GHz optical receiver module packaging. The simulation results were compared to the measured laboratory data. The proposed package has low cost and easy manufacture process far mass production. Using this package, we had a good optical to electrical conversion (OE) characteristic at a data rate of 10Gbps.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.17 no.8 s.111
• /
• pp.767-772
• /
• 2006

The receiver of this paper is Dual-band monopulse type for prototype of tracking radar. Localization of radar technology is an issue of SamsungThales and go into development. Dual-band radar in comparison with Single-band radar requires higher cost and power consumption but there are many advantages of dealing with jamming, detection range, image signal rejection, cloud-rain influence, clutter, resolution. The receiver is comprised of X-band RF head module, Ka-band RF head module and common IF module. Each signal of X-band and Ka-band is selected by the switch in If module. Phase shifter in IF module of local stage controls the phase of sum, azimuth, elevation channel. In the test result, gain is $40{\pm}3 dB$, isolation of transmitter/receiver is 39 dBc, dynamic range is 110 dB and noise figure of each channel is 4.5dB and 6.9dB.

• ETRI Journal
• /
• v.35 no.1
• /
• pp.1-6
• /
• 2013

In this paper, we present an implemented serial 40-Gb/s receiver optical subassembly (ROSA) module by employing a proposed TO-CAN package and flexible printed circuit board (FPCB). The TO-CAN package employs an L-shaped metal support to provide a straight line signal path between the TO-CAN package and the FPCB. In addition, the FPCB incorporates a signal line with an open stub to alleviate signal distortion owing to an impedance mismatch generated from the soldering pad attached to the main circuit board. The receiver sensitivity of the ROSA module measures below -9 dBm for 40 Gb/s at an extinction ratio of 7 dB and a bit error rate of $10^{-12}$.

• The Journal of the Korea Contents Association
• /
• v.6 no.1
• /
• pp.8-13
• /
• 2006

In this thesis, an automatic door lock system using a dual tone multiple frequency(DTMF) signal generated as pushing the key button of mobile phone is proposed and implemented. This system consists of a transmitter module and a receiver module for processing the DTMF signal of mobile phone. The DTMF signal of mobile phone connected with ear-phone jack enter into the input terminal of DTMF receiver and those are encoded by a code-converter with 4-bits binary format in the DTMF receiver. The encoded output signals are transmitted to the amplitude shift keying(ASK) modulator of transmitter module and the modulated ASK signals which are converted into radio frequency(RF) signals propagate in a free space. The RF signals passed through a free space are demodulated by the ASK demodulator of receiver module and the demodulated ASK signals are sent to a micro-controller unit(MCU). The output signals processed by the MCU are compared with the secreted identification number which is prerecorded in a microprocessor and are transferred to a power relay. If the result is the same, the automatic door lock system opens a door. In the opposite case, it maintains closing the door. The implemented automatic door lock system operates well in mobile environments.

• Journal of the Microelectronics and Packaging Society
• /
• v.7 no.3
• /
• pp.19-25
• /
• 2000

In this paper, we describe RF receiver module for IMT-2000 handset with 5 MHz channel bandwidth. The fabricated RF receiver module consists of Low Noise Amplifier, RF SAW filter, Down-converter, If SAW filter, AGC and PLL Synthesizer. The NF and IIP3 of LNA is 0.8 dB, 3 dBm at 2.14 GHz, conversion gain of down-converter is 10 dB, dynamic range of AGC is 80 dB, and phase noise of PLL is -100 dBc at 100 kHz. The receiver sensitivity is -110 dBm, adjacent channel selectivity is 48 dBm.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.6 no.1
• /
• pp.51-56
• /
• 2013

In this paper, we had design the module of the LED-based media transmission mechanics visible light communication system. To implement the media transmission system through visible light communication transmitter, receiver module the using high brightness, we proposed visible light communication system to implement communication distance of up to a maximum transmitter-receiver distance using a variable PD sensor to the receiver and 1~12 the LED light-emitting device to the transmitter. It was increased efficiency of approximately 20% by measuring the performance during lens wearing or not wearing on the LED module to improve the efficiency of the media transmission system.

• Korean Journal of Optics and Photonics
• /
• v.5 no.2
• /
• pp.333-339
• /
• 1994

We fabricated a single mode fiber pigtailed PIN-preamplifier front-end receiver module for the high speed optical receiver. Hybrid method was used to integrate GaInAs PIN photodiode and transimpedance type GaAs preamplifier. The capacitance and the diameter of light receiving area of PIN photodiode were 0.35 pF and $20{\mu}m$ respectively. The -3 dB cut-off frequency of PIN-preamplifier module was above 2 GHz, and the sensitivity of the module at 2.5 Gbps NRZ $(PRBS=2^{23}-1)$ signal was -25.2 dBm at $10^{-9}$ BER. > BER.

• Proceedings of the KIEE Conference
• /
• 2004.07d
• /
• pp.2173-2175
• /
• 2004

This paper addresses a telemetering device which uses RF transceivers and a mobile-phone. Locally collected data arc encoded with a BCH error correcting code and transferred to a receiver through a RF module. The receiver-side RF module decodes the transferred data and then repetes them to a mobile-phone. Lastly, the mobile-phone hands over the data through a wireless phone network to a host computer in the internet.

• Journal of the Semiconductor & Display Technology
• /
• v.16 no.2
• /
• pp.85-88
• /
• 2017

In this paper, we have designed and fabricated a RF-DC voltage multiplier for 5.8GHz microwave wireless power transmission. In order to obtain higher voltage, the RF-DC voltage multiplier with 10 diodes (D-10) and the receiver module with an antenna and BPF (Band Pass Filter) was manufactured. The measured and compared results show that the voltages of the proposed one are lower than those of the previous tripler module up to 40cm. However, the voltage of the proposed one with the voltage multiplier is higher than that of the tripler module at the distances of 45cm and 50cm due to the voltage multiplier with 10 diodes.

• Smart Media Journal
• /
• v.7 no.3
• /
• pp.29-34
• /
• 2018

This paper presents a study on adapting optical communication technology using infrared ray for the enhancement of hearing aids in noisy environment. The transmitter module containing microphone and infrared ray-emitting diode converts audio signal to infrared optical signal and sends it out in the air. The receiver module located in a distance receives the infrared signal, converts it to electrical signal, and transfers it to an input of a digital hearing aid. Especially, the receiver module needs to be small, low voltage, and consume low power since it will be attached to hearing aids. Experiments with applying infrared communication technology of digital modulation method and analog non-modulation method show that the analog non-modulation method is adequate for infrared communication of approximately 5m distance indoor. Prototypes of transmitter module and receiver module were manufactured, and internal parameters of the digital hearing aid were adjusted to confirm normal transmit-receive operation of audio signals.