• 한국자동차공학회논문집
• /
• 제13권1호
• /
• pp.194-203
• /
• 2005

The process of guaranteeing that a distributed real-time control system will meet its timing constraints, is referred to as schedulability analysis. However, schedulability analysis algorithm cannot be simply used to analyze the system because of complex calculations of algorithm. It is difficult for control engineer to understand the algorithm because it was developed in a software engineer's position. In this paper we introduce a Response-time Analysis Tool(RAT) which provides easy way far system designer to analyze the system by encapsulating calculation complexity. Based on the RAT, control engineer can verify whether all real-time tasks and messages in a system will be completed by their deadline in the system design phase.

• 제어로봇시스템학회논문지
• /
• 제10권10호
• /
• pp.940-946
• /
• 2004

In this paper, an efficient real-time control architecture for autonomous navigation of powered wheelchair is developed. Since an advanced intelligent wheelchair requires real-time performance, the control software architecture of powered wheelchair is developed under Linux real-time extension Real-time Application Interface (RTAI). A hierarchical control structure for autonomous navigation is designed and implemented using real-time processe and interrupts handling of sensory perception based on slanted surface LRF, emergency handling capability, and motor control with 0.1 msec sampling time. The performance of our powered wheelchair system with the implemented control architecture for autonomous navigation is verified via experiments in a corridor.

• 제어로봇시스템학회논문지
• /
• 제21권3호
• /
• pp.187-193
• /
• 2015

When developing a vehicle control system, simulation methods are widely used to validate the whole system in the early development phase. With this regard, the simulator should correctly behave just like the real parts that are not yet implemented while interacting with already implemented parts in real-time. However, most simulators cannot provide functionally and temporally accurate behaviors of the target system. In order to overcome this limitation, this paper proposes a novel real-time simulation technique that can efficiently simulate the temporal behavior as well as the functional behavior of the simulation target system.

• 한국정밀공학회지
• /
• 제12권5호
• /
• pp.108-116
• /
• 1995

A tension control strategy for a multi-span web transport system is proposed. This strategy is developed by using the tension transfer phenomena in multi-span systems. The performance of this control strategy is compared with that of an existing control strategy through a computer simulation. A real-time software is designed based on the proposed tension control stration of master speed drive in tension control is demonstrated.

• 대한전기학회논문지:전력기술부문A
• /
• 제48권6호
• /
• pp.760-772
• /
• 1999

The CAN is a serial communication protocol for distributed real-time control and automation systems. Data generated from field devices in the distributed control of power plant are classified into three categories: real-time event data, real-time control data, non-real-time data. These data share a CAN medium. If the traffic of the CAN protocol is not efficiently controlled, performance requirements of the power plant system could not be satisfied. This paper proposes a bandwidth allocation algorithm that can be applicable to the CAN protocol. The bandwidth allocation algorithm not only satisfies the performance requirements of the real-time systems in the power plant but also fully utilizes the bandwidth of CAN. The bandwidth allocation algorithm introduced in this paper is validated using the integrated discrete-event/continuous-time simulation model which comprises the CAN network and distributed control system of power plant.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2001년도 Proceedings ICPE 01 2001 International Conference on Power Electronics
• /
• pp.546-551
• /
• 2001

This paper considers the design technique of the real-time control algorithm to implement the electronic interlocking system which is the most important station control system in railway signal field. The proposed technique consists of the structure design and the detail design which are based on the ROOM(Real-Time Object-Oriented Modeling) This proposed technique is applied to the typical station model in order to prove the validity as verifying the performance of the modeled station.

• 항공우주시스템공학회지
• /
• 제9권1호
• /
• pp.12-18
• /
• 2015

The inter-conversion between different control laws in flight has a lot of risk. The SWM(Switching Mechanism) including logic and stand-by mode is designed to analyze the transient response of aircraft during inter-conversion between different control laws, based on the in-house software for non-real-time and real-time simulation. The SWM applies the fader logic of TFS(Transient Free Switch) to minimize the transient response of an aircraft during the inter-conversion, and applies the reset '0' type of the stand-by mode to prevent surface saturation due to integrator effect in the disengaged flight control law. The transition time is also important to minimize the objectionable transient response in the inter-conversion, as well as the transition control law design. This paper addresses the results of non-real-time simulation for the characteristics of transient response to different transition time to select the adequate transient time, and the real-time pilot evaluation, using SSWM(Software Switching Mechanism) and HSWM(Hardware Switching Mechanism), which is met for Level 1 flying qualities and assures safety of flight.

• 한국해양공학회:학술대회논문집
• /
• 한국해양공학회 2004년도 학술대회지
• /
• pp.198-203
• /
• 2004

This paper describes a real-time control architecture for DUSAUV (Dual Use Semi-Autonomous Underwater Vehicle), which has been developed at Korea Research Institute of Ships & Ocean Engineering (KRISO), KORDI, for being a test-bed oj development of technologies for underwater navigation and manipulator operation. DUSAUV has three built-in computers, seven thrusters for 6 degree of freedom motion control, one 4-function electric manipulator, one pan/tilt unit for camera, one ballasting motor, built-in power source, and various sensors such as IMU, DVL, sonar, and so on. A supervisor control system for GUI and manipulator operation is mounted on the surface vessel and communicates with vehicle through a fiber optic link. Furthermore, QNX, one of real-time operating system, is ported on the built-in control and navigation computers of vehicle for real-time control purpose, while MicroSoft OS product is ported on the supervisor system for GUI programming convenience. A hierarchical control architecture which consist of three layers (application layer, real-time layer, and physical layer) has been developed for efficient control system of above complex underwater robotic system. The experimental results with implementation of the layered control architecture for various motion control of DUSAUV in a basin of KRISO is also provided.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2000년도 제15차 학술회의논문집
• /
• pp.120-120
• /
• 2000

In this study, in order to control real system under the environment of graphic user interface, study on the technique which can control real system without additional hardware drivers using virtual machine driver operated on the windows operating system. Consider the problem which is the error and the delay of a sampling time on the multi task processing through the load test of the experiment using graphic user interface.

• 대한전기학회논문지:시스템및제어부문D
• /
• 제53권3호
• /
• pp.182-187
• /
• 2004

In this paper, we propose a PC based distributed controller for a two axis convey table using real-time micro-kernel. PC, Windows program, gives an easy way to implement wealthy GUI and micro-kernel, ${\mu}$C/OS-II, provides a real-time capability to control devices. We built a real-time distributed control system using ${\mu}$C/OS-II kernel which needs to process the tasks for two motors within the desired time to synchronize the motion. We used both semaphore and message mail box for synchronization. Unlike the previous study where we used step motors for the actuator of two axes convey table, we rebuilt the convey table with DC motors and the dedicated position servo which had built in out lab, and then we implemented a realtime distributed control system by putting the micro-kernel into between PC and position servo. Moreover we developed the PC based graphic user interfaces for generating planar drawing image control. Experimental results also presented to show the Proposed control system is useful.