• Journal of Korean Society of Industrial and Systems Engineering
• /
• v.37 no.1
• /
• pp.33-40
• /
• 2014

Air compressor is an important facility with electric power in the industry. However, because of the noise and vibration of air compressor and is installed outside the building management difficulty. In this study, MCP (Micro Control Processor) to remote monitoring of the air compressor via the compressed air through improved quality and allows stable maintenance were designed. So, increase the productivity improvement of energy-saving effect can be obtained. Remote real-time information stored on your PC to manage air compressor equipment was higher reliability. Monitoring system is developed in this study was applied to embedded systems. It is easy to install air compressor, and low maintenance costs was to raise the economic impact.

• Proceedings of the KIEE Conference
• /
• 2009.04b
• /
• pp.201-203
• /
• 2009

This paper presents the real time stray current monitoring techniques on the DC railway system. These techniques are two types. The first one is the rail potential measurement technique between running rail and earthing mats on the important locations such as substation, station, and so on. And the second one is measurement technique of stray current through substation earthing mats and from collection mats, and continuous monitoring of return currents through the running rails. We need to apply these techniques on DC railway system to monitor stray current periodically and maintain the system properly.

• Journal of the Korean Society of Safety
• /
• v.20 no.3 s.71
• /
• pp.1-8
• /
• 2005

The industrial induction motor is widely used in the rotating electrical machine for the transmission of power. It is very reliable equipment, but it could lead to the loss of production and lift when failure occurs. Therefore, the failure data is acquired and analyzed by attaching an exclusive instrument to existing induction motor. However, these instruments could lead to side effects, increasing the production costs, because they are very expensive. The purpose of this study is the development of an induction motor bearing failure diagnosis system constructed using LabVIEW which can be supplied the kernelled function, process monitoring and current signature analysis. In addition, the availability and reasonability of the constructed system was examined for an induction motor with failure defects in outer raceway and ball bearing. From the results, it shows that failure diagnosis system constructed is useful for real-time monitoring with detection of bearing defects over the web.

• Journal of Advanced Navigation Technology
• /
• v.17 no.6
• /
• pp.664-671
• /
• 2013

In this paper, in an aircraft power can be measured by wireless AEMS (aircraft electric power measurement monitoring system) system is proposed. AEMS has been design based on current commercialized power measuring systems analysis with improvement and connects it with most talked about item, smart phone and monitoring system. And also adopting real time power measuring system, constitute more practical power measuring system by controlling electricity usage in real time.

• Journal of Information Processing Systems
• /
• v.15 no.3
• /
• pp.478-491
• /
• 2019

This work develops a monitoring system for the population with health concerns. A belt integrated with an on-body circuit and sensors measures a wearer's selected vital signals. The electrocardiogram sensors monitor heart conditions and an accelerometer assesses the level of physical activity. Sensed signals are transmitted to the circuit module through digital yarns and are forwarded to a mobile device via Bluetooth. An interactive application, installed on the mobile device, is used to process the received signals and provide users with real-time feedback about their status. Persuasive functions are designed and implemented in the interactive application to encourage users' physical activity. Two signal processing algorithms are developed to analyze the data regarding heart and activity. A user study is conducted to evaluate the performance and usability of the developed system.

• IEMEK Journal of Embedded Systems and Applications
• /
• v.14 no.3
• /
• pp.123-131
• /
• 2019

In recent years, a non-contact respiration and heart rates monitoring via IR-UWB radar has been paid much attention to in various applications - patient monitoring, occupancy detection, survivor exploring in disaster area, etc. In this paper, we address a novel approach of real time heart rate estimation using IR-UWB radar. We apply sine fitting and peak detection method for estimating respiration rate and heart rate, respectively. We also deploy two techniques to mitigate the error caused by wrong estimation of respiration rate: a moving average filter and finding the frequency of the highest occurrence. Experimental results show that the algorithm can estimate heart rate in real time when respiration rate is presumed to be estimated accurately.

• International Journal of Naval Architecture and Ocean Engineering
• /
• v.12 no.1
• /
• pp.902-909
• /
• 2020

It is announced a new procedure for the real-time overall hull response monitoring system depends on inclinometer sensor data. The procedure requires a few inclinometer sensors' data, located on the deck. Sensor data is used to obtain curvature values; and curvature values are used to find out displacements or relevant moment values according to pre-calculated moment-curvature diagrams. Numerical studies are demonstrated with reasonable accuracy for the pre-ultimate and the post-ultimate nonlinear behaviors. Elastic, inelastic, and post-collapse structural bending moment capacity determination of the hull has been presented. The proposed inverse engineering technique will be able to see the response of the hull in real-time with high accuracy to manage the course and speed when cruising or control the loading and the unloading process at the port.

• Journal of Korea Multimedia Society
• /
• v.25 no.8
• /
• pp.1085-1096
• /
• 2022

The manufacturing industry is continuously pursuing advanced technology and smartization as it converges with innovative technology. Improvement of manufacturing productivity is achieved by monitoring, analyzing, and controlling the facilities and processes of the manufacturing site in real time through a network. In this paper, we proposed a new OPC-UA based digital twin model for smart factory facilities. A testbed system for USB flash drive packaging facility was implemented based on the proposed digital twin model and OPC-UA data communication scheme. Through OPC-UA based digital twin model, equipment and process status information is transmitted and received from PLC to monitoring and control 3D digital models and physical models in real time. The usefulness of the developed digital twin testbed system was evaluated through usability test.

• International Journal of Korean Welding Society
• /
• v.3 no.1
• /
• pp.45-50
• /
• 2003

Welding using lasers can be mass-produced in high speed. In the laser welding, performing real-time monitoring system of the welding quality is very important in enhancing the efficiency of welding. In this study, the plasma and molten metal which are generated during laser welding were measured using the UV sensor and IR sensors. The results of laser welding were classified into five categories such as optimal heat input, little low heat input, low heat input, partial joining due to gap mismatch, and nozzle deviation. Also, a system was formulated which uses the measured signals with a fuzzy pattern recognition method which is used to perform real-time evaluation of the welding quality and the defects which can occur in laser welding.

• International conference on construction engineering and project management
• /
• 2017.10a
• /
• pp.252-259
• /
• 2017

Nowadays, the existing manual method for recording actual progress of the construction site has some drawbacks, such as great reliance on the experience of professional engineers, work-intensive, time consuming and error prone. A method integrating computer vision and BIM(Building Information Modeling) is presented for indoor automatic progress monitoring. The developed method can accurately calculate the engineering quantity of target component in the time-lapse images. Firstly, sample images of on-site target are collected for training the classifier. After the construction images are identified by edge detection and classifier, a voting algorithm based on mathematical geometry and vector operation will divide the target contour. Then, according to the camera calibration principle, the image pixel coordinates are conversed into the real world Coordinate and the real coordinates would be corrected with the help of the geometric information in BIM model. Finally, the actual engineering quantity is calculated.