• Journal of Korean Society on Water Environment
• /
• v.18 no.3
• /
• pp.245-251
• /
• 2002

Reactive dyes waste water, a toxic and refractory pollutant, was treated by an electrochemical method using $Ti/IrO_2$ as anode and Stainless Steel 316 as cathode. In this technique, sodium chloride as an electrolyte was added. A number of experiments were run in a batch system. Artificial samples (reactive blue 19, red 195, yellow 145) were used. Operation parameters, such as supporting electrolyte concentration, current density, pH and sample concentration have been investigated for their influences on COD and color removal efficiencies during electrolysis. After 5 and 90 minites of eletrolysis, color was reduced by 51.5% and 98.9% respectively. Under the condition of current density $10A/dm^2$, NaCl concentration 12mg/l and pH 3, 62.9% of $COD_{Cr}$ was removed after electrolysis for 90 minites. The optimum condition of color removal and COD reduction in this work was found to be the following : pH 3, sodium chloride concentration 20g/l, current density $10A/dm^2$. As a result, we confirmed to be effective to color removal and reduction of refractory organic material.

• Textile Coloration and Finishing
• /
• v.33 no.4
• /
• pp.210-219
• /
• 2021

It was intended to conduct basic research to reduce development lead time and cost consumed in DTP process technology development. For the simulation of HTPE fabric, virtual engineering software was used to generate fiber model, yarn model, fabric model, and finite element model of HTPE fiber. The purpose of this study is to analyze the correlation and error rate between the stiffness numerical analysis results according to the direct DTP process parameters using reactive dyes in the generated finite element model and the stiffness measurements of the actual sample ac- cording to ASTM D1388. And, after dyeing the HTPE plain fabric according to the direct DTP process parameters, we want to analyze the dyeability of the HTPE fabric fabrics according to the direct DTP process parameters through the color fastness analysis. When looking at the results of the analysis of the finite element model, a higher value was shown when the distance between the nozzle and the fabric was 3mm than when the distance was 10mm. When the distance between the nozzle and the fabric was 10mm and 7mm, the reactive dye did not penetrate sufficiently, resulting in poor clarity when viewed with the naked eye.

• Journal of the Korean Wood Science and Technology
• /
• v.45 no.3
• /
• pp.297-307
• /
• 2017

This research was performed to use recycling wood fiber from waste MDF as raw materials for manufacturing of interior decorative accessories. Virgin fiber of Pinus rigida for manufacturing MDF and recycling fiber from manufactured MDF with virgin fiber were dyed by using reactive dyes (Bis-monochlorotriazine and Vinyl sulfone type), vat dyes (Anthraquinone type), direct dyes (Diazo type) such as red, yellow and blue, and natural dyes using gardenia or sappan wood, and they were examined to evaluate their dyeing properties and sunlight fastness. The hue of virgin fiber and recycling fiber were 4.2YR, and 4.4YR, respectively, which showed red-yellowish color. The recycling fiber looked a little darker than the virgin fiber, where $L^*$ values of the recycling fiber showed a little lower. Reactive, vat and direct dyes dyed well both the virgin and recycling fibers. The recycling fiber showed a little higher values of colour yield and a little lower in $L^*$, but it seemed that there was no significant difference. The Hue values of the recycling fiber and the virgin fiber dyed with sappan wood were 4.4YR and 4.0YR, showing no difference between/after dyeing. However the Hue values of the recycling fiber and the virgin fiber dyed with gardenia were 7.4YR and 6.9YR, respectively. Those values were much higher than the values of the fibers dyed with other chemical dyes. But the fibers dyed with gardenia showed poor sunlight fastness.

• Textile Coloration and Finishing
• /
• v.18 no.4
• /
• pp.43-48
• /
• 2006

A phthalocyanine reactive dye was applied to nylon fibers to study the effects of the temperature and pH on % exhaustion and fixation. In addition, appropriate predictable empirical models, relatively new approaches in dyeing process, were developed incorporating interactions effects of temperature and pH for predicting the both % exhaustion and fixation. The significance of the mathematical model developed was ascertained using Excel regression (solver) analysis module. A very high correlation coefficient was obtained ($R^2=0.9895$ for % exhaustion, $R^2=0.9932$ for fixation) for the model which shows prominent prediction capacity of the model for the unknown conditions. The predictable polynomial equations developed from the Experimental results were thoroughly analyzed by ANOVA (Analysis of Variance) statistical concepts.

• Journal of Korean Society of Environmental Engineers
• /
• v.22 no.11
• /
• pp.2077-2083
• /
• 2000

For the application of wet air oxidation(WAO) process reactive dyes, remazol blacks has been selected as the subject for this study. The rate of decomposition relating to the reaction temperature and catalyst has been summarized during the catalytic wet air oxidation reaction. When 1.5 gram per liter of platinum is added titanium-dioxide and the partial pressure is adjusted to 6 atmosphere at the reaction temperature exceeding $200^{\circ}C$, more than 95% of the remazol blacks dyes were decomposed. When the reaction temperature was raised to $200^{\circ}C$, $220^{\circ}C$ and $250^{\circ}C$, respectively, for 240 minutes after adding the catalyst, the remaining rate of ultraviolet absorbance had dropped significantly to 18%, 12%, and 4%. At the reaction temperature of $250^{\circ}C$, color removal efficiency was approximately 95% or more after 120 minutes from the beginning of the reaction.

• Journal of Adhesion and Interface
• /
• v.13 no.3
• /
• pp.131-136
• /
• 2012

In this study, commercial poly(vinyl alcohol) (PVA) film was dyed with reactive dichroic dyes under mild conditions using organic solvents in stead of strong basic aqueous solution. After drawing of 500% of this PVA film, the polarizing efficiency and the single piece transmittance were measured. The degree of saponification of the commercialized PVA film was determined by using NMR and FT-IR spectromety. The commercial PVA film, with ca. 100% of the degree of saponification determined by NMR spectrometry, was dyed with the reactive dichroic dyes, which have 3,5-dichloro-2,4,6-triazine moiety. As a result, we found that the PVA film dyed with the reactive congo red showed relatively good polarization efficiency, and the PVA film dyed with the reactive direct black 22 exhibited relatively good single piece transmittance.

• Textile Coloration and Finishing
• /
• v.17 no.1
• /
• pp.14-19
• /
• 2005

Study on the use of enzymes for textile wet processing has been very active. The exploratory research conducted herein is related to the bioscouring process for cotton fabric. The optimum concentration of alkaline pectinase(BioPrep) was in the range of 0.05～0.2 g/l, the proper treatment time was 30～60 minutes, the appropriate treatment temperature was $60^{\circ}C$ for both the batch method and the padding method. The simultaneous desizing/bioscouring by padding method did not give water absorbency as good as the bioscouring after desizing. Color of fabrics which were bioscoured and dyed with direct dyes and a reactive dye was just a little darker than that of NaOH scoured one. K/S and Lab values of the bioscoured fabrics, regardless of the degree of water absorbency, were quite similar to each other.

• Proceedings of the Korean Society of Dyers and Finishers Conference
• /
• 2012.03a
• /
• pp.26-26
• /
• 2012

The hydrophobic nature of the wool surface give rise to difficult penetration of dye molecules. Among all the methods of modification, graft polymerization is an attractive method to impart a variety of functional groups to a polymer. Grafting has been made by irradiating the light on the polymer in the presence of a solvent containing monomer. The energy source commonly used are high-energy electrons, X-rays, UV and visible light. UV irradiation is a relatively low-energy radiation in comparison with others since it has the least possibility to change bulk properties. In the present paper, a photo-reactive dye was synthesized from quinizarin by the reaction with methacryloyl chloride. The synthesized dye was continuously grafted onto wool fabric at room temperature by UV irradiation. Several key parameters including UV energy, dye concentration and pH have been examined to understand their influence on the photoreactive coloration.

• Fibers and Polymers
• /
• v.5 no.1
• /
• pp.52-58
• /
• 2004

Previous investigation results revealed that after the Low Temperature Plasma (LTP) treatment, the hydrophilicity of wool fiber was improved significantly. Such improvement enhances the wool dyeing and finishing processes which might be due to the changes of the wool surface to a more reactive one. In this paper, wool fibers were treated with LTP with different gases, namely, oxygen, nitrogen and gas mixture (25 % hydrogen/75 % nitrogen). Investigations showed that chemical composition of wool fiber surface varied differently with the different plasma gas used. The surface chemical composition of the different LTP-treated wool fibers was evaluated with different characterization methods, namely FTIR-ATR, XPS and saturated adsorption value. The experimental results were thoroughly discussed.

• Textile Coloration and Finishing
• /
• v.7 no.2
• /
• pp.70-76
• /
• 1995

The polyepichlorohydrine(poly(ECH)) was prepared by the condensation polymerization of epichlorohydrine. The cationic agent was prepared from poly(ECH) by amination of poly(ECH) with dimethyleneamine. Pretreatment of cellulosic fabric with the poly(ECH)amine produced a modified fabrics that could be dyed under neutral condition with reactive dye using small amount of the salt. Colour yield of cellulosic fabric were increased by increasing salt concentraction. cationic agent concentration. The optimum condition for colour yield was the concentration of cationic agent 5%(o.w.f), that of NaCl 4g/l, and that of $Na_{2}CO_{3}$5g/l. The dyeing of treated fabrics exhibits improved colour yield and high wash fastness.