• Journal of the Korean earth science society
• /
• v.23 no.1
• /
• pp.105-111
• /
• 2002

The observation of the new biotite isograd (chlorite + chloritoid = andalusite + biotite) in the Mungyong coal field requires the modification of Harte and Hudson's (1979) metapelite grid which eliminates the stability field of staurolite + cordierite assemblages. The newly proposed metapelite grid by Ahn and Nakamura (2000) can define more properly the isograd reaction observed from nature. We discuss first topological interrelations between synthetic system (FASHO-, KFASHO-, KFMASH system) on an isobaric section at 2kbar, where phase relations are well constrained. The following discussion is concentrated on the topological relations between stable reactions. At the last, we discuss the petrogenetic significance of the Ahn's petrogenetic grid compared with theoretically computed grids. Ahn's petrogenetic grid is consistent with synthetic and natural system, and is one of the excellent example of KFMASH approximation in metapelite.

• Transactions of Materials Processing
• /
• v.24 no.2
• /
• pp.101-106
• /
• 2015

Recently, silicone is being used for LED chip lens due to its good thermal stability and optical transmittance. In order to predict residual stresses, which cause optical birefringence and mechanical warpage of silicone, a finite element analysis was conducted for the curing of silicone during molding. For the analysis of the curing process, a dynamic cure kinetics model was derived based on the results of a differential scanning calorimetry (DSC) testing and applied to the material properties for finite element analysis. Finite element simulation results showed that a step cure cycle reduced abrupt reaction heat and showed a decrease in the residual stresses.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2014.10a
• /
• pp.173-174
• /
• 2014

Vibration disturbances generated by reaction wheels may cause serious problems in high precision pointing spacecraft missions. Implementation of vibration isolator is a practical solution to meet the high pointing stability requirement placed on precision payloads. In this paper, development of hybrid vibration isolator that combines passive and active component is described. Vibration isolation performance of the developed isolator is evaluated using reaction wheel disturbance model. Hybrid isolation results obtained using FxLMS algorithm show clear improvement compared to the results obtained using only passive means.

• Journal of the Society of Cosmetic Scientists of Korea
• /
• v.22 no.2
• /
• pp.89-98
• /
• 1996

A novel polymeric sunscreen agent was developed. It was prepared by the coupling reaction of 2-ethylhexyl 4-hydroxycinnamate with poly vinylbenzyl chloride(PVBC, average MW 6,500). In this reaction the reactivity was mostly affected by catalyst. In the absence of catalyst the yield was approximately 55% and in the presence of tetrabutylammonium bromide the yield was about 65%, but in the presence of tetrabutylammonium iodide the yield was 100% to give a average molecular weight 20,000 polymeric sunscreen agent. There were no side reactions, and its structure and purity were confirmed by various analytical methods, such as NMR, IR, and so on. UV radiation absorption efficiency is more than 70% compared with that of octyl methoxycinnamate. The solubility in polar oil, for example C12-15 alkylbenzoate and caprylic/capric triglyceride, is more than 50%. It showed high stability in the time course of test including acceleration test. This polymer is safe to skin because of poor permeability to skin, no side products in the process of preparing, and easy elimination of excess starting materials.

• Bulletin of the Korean Chemical Society
• /
• v.31 no.11
• /
• pp.3238-3240
• /
• 2010

A new and efficient method for the preparation of substituted 3,4-dihydropyrimidin-2(1H)-ones via Biginelli synthesis using catalytic amounts of 1,3-dichloro-5,5-dimethylhydantoin is presented. Short reaction times, easy work-up, high yields of products and stability, easy-handling, non-toxicity and cheapness of the catalyst are noteworthy advantages of the present work.

• Journal of Korean Society for Atmospheric Environment
• /
• v.12 no.4
• /
• pp.479-485
• /
• 1996

Volatile organic compounds are air pollutants exhausting from industrial process, evaporation of solvent, and so on. Most of VOCs are the combustible gas of low calorific value as it is diluted by air. The systems burning such a hazardous gas need to increase enthalpy in order to increase flame stability. In this study an incinerator with reciprocating flow in the honeycomb ceramic has been used for the experiment of VOCs control. By the reciprocating flow system, the enthalpy of combustion gas is effectively regenerated into the enthalpy increases of the combustible gas through the honeycomb ceramic, which provides a heat storage. The position of the reaction zone is strongly dependent on the parameters of mixture velocity and time frequency. Flame front is changed to the point where burning velocity is coincided with burning velocity in the honeycomb ceramic. In this system it is important that flame front should be located symmetrically at the center of honeycomb ceramic for the purpose of increasing the reaction rate at one point. Peak temperature becomes higher with decreasing time frequency, at which the flow direction is regularly reversed.

• Journal of Powder Materials
• /
• v.25 no.5
• /
• pp.390-394
• /
• 2018

Metallic tantalum powder is manufactured by reducing tantalum oxide ($Ta_2O_5$) with magnesium gas at 1,073-1,223 K in a reactor under argon gas. The high thermodynamic stability of magnesium oxide makes the reduction reaction from tantalum oxide into tantalum powder possible. The microstructure after the reduction reaction has the form of a mixture of tantalum and magnesium oxide, and the latter could be entirely eliminated by dissolving in weak hydrochloric acid. The powder size in SEM microstructure for the tantalum powder increases after acid leaching in the range of 50-300 nm, and its internal crystallite sizes are observed to be 11.5 to 24.7 nm with increasing reduction temperatures. Moreover, the optimized reduction temperature is found to be 1,173 K as the minimum oxygen concentration is approximately 1.3 wt.%.

• 한국연소학회:학술대회논문집
• /
• 1998.10a
• /
• pp.1-8
• /
• 1998

Waste combustion above a grate is the core process of incineration systems, stability of which should be guaranteed for emission minimization. However, complicated reactions and heat and mass transfer phenomena make understanding the process difficult. One dimensional bed combustor with a numerical combustion model is utilized to investigate the combustion process of the bed, using cubic wood particles as a simulated fuel. Bed combustion behavior is characterized with apparent flame propagation speed, which has close relationship with air supply rate and chemical and physical characteristics of the fuel. Base on the availability of oxygen, two distinct reaction zone is identified; the oxygen-limited and the reaction-limited zone leading to the extinction by excessive convection cooling. The numerical modeling shows good agreement with the experimental results. The transient bed combustion behavior of local temperature and oxygen consumption rate is adequately reproduced. The numerical model is extended to model the waste bed combustion of a commercial incineration plant, which shows meaningful results as well.

• 한국연소학회:학술대회논문집
• /
• 1998.10a
• /
• pp.59-67
• /
• 1998

The aim of this study is to investigate advantages that the catalytically supported combustor can have. For this purpose, the catalytic combustor was prepared which consisted of the catalyst bed and the thermal combustor at the downstream of the catalyst bed. The catalyst bed consisted of two-stage. Pd catalyst was installed in the first stage of the catalyst bed, and Pt catalyst was placed in the second stage. Results showed that the catalytically supported combustion had some advantages. One was that auto-ignition occurred in the thermal combustor. This can give merit that an igniter is not necessary to start flame ignition. Other was that the catalytically supported combustion was stable for lean mixture. When combustion of lean mixture was not supported by surface reaction it became unstable so that big combustion noise was created. Therefore, it is desirable to support flame by catalytic surface reaction to obtain the stable combustion of lean mixture.

• Elastomers and Composites
• /
• v.28 no.4
• /
• pp.267-273
• /
• 1993

A number of hydrophilic acrylic comonomers were incorporated into styrene-butadiene soap-free emulsion polymerization. It was found that reaction rate decreased according to : AN>AA>MMA>EA>IA>AAM>MA>HEMA. It was also observed that reaction rate increased with decreasing H-bonding factor contribution to the solubility parameter of the hydrophilic comonoer. The SBR latexes were very monodisperse with the particle size distribution of $1.03{\times}1.12$. Since growth rate is proportional to polymerization time, the difference in conversion rates between various comonomers was resulted from the particle number density of SBR latexes for the various hydrophilic comonomers. It was also found that the colloidal stability of the latexes was excellent because no external emulsifier was incorporated.