• Geomechanics and Engineering
• /
• 제25권2호
• /
• pp.89-98
• /
• 2021

The paper presents an experimental study on the strength behaviour of a coral gravelly sand from Vietnam subjected to monotonic and cyclic loading. A series of direct shear tests were carried out to investigate the shear strength behaviour and the factors affecting the shear strength of the sand such as relative density, cyclic load, amplitude of the cyclic load and loading rate. The study results indicate that the shear strength parameters of the coral gravelly sand include not only internal friction angle but also apparent cohesion. These parameters vary with the relative density, cyclic load, the amplitude of the cyclic load and loading rate. The shear strength increases with the increase of the relative density. The shear strength increases after subjecting to cyclic loading. The amplitude of the cyclic load affects the shear strength of coral gravelly sand, the shear strength increases as the amplitude of the cyclic load increases. The loading rate has insignificantly effect on the shear strength of the coral gravelly sand.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 춘계학술대회논문집A
• /
• pp.395-400
• /
• 2001

The Split Hopkinson Pressure Bar(SHPB) technique, a special experimental apparatus, has been used to obtain the material behavior under high strain rate loading condition. In this paper, dynamic deformation behaviors of the PMMA under high strain rate tensile loading are determined using SHPB technique.

• Journal of Animal Science and Technology
• /
• 제45권4호
• /
• pp.641-648
• /
• 2003

본 연구에서는 돈사 폐수내의 인과 질소를 함께 결정화하여 회수하고 그 상등액을 전기분해 시키는 회분식 돈사 폐수공정에서의 오염물질 부하량과 수처리시간 변화에 따른 처리효율의 변화 및 각 오염물질 제거특성을 파악하였다. Struvite 형성을 위한 Mg원으로는 $MgCl_2$를 사용하였고 주입량은 폐수내 인 기준 1.3 Mole이었다. 총 4개의 운전(Run I, II, III, IV)에서 얻어진 평균 제거효율과 그 제거특성을 분석한 결과 인의 경우 부하량 변화에 따른 처리효율의 변화는 관찰되지 않았으며 제거의 주요 역할을 하는 반응조는 Struvite 반응조로서 적정 Mg원만 제공된다면 pH 조절제 첨가 없이 폭기만으로도 부하량에 관계없이 88% 이상의 제거가 MAP 형성을 통해 얻어지는 것으로 나타났다. 높은 암모니아성 질소 제거효율을 유지하기 위한 적정 부하량은 약 100g/$m^3$.d로서 동 부하량 이하에서는 부하량이 증가함에 따라 제거량도 증가하면서 90% 이상의 높은 효율과 일정한 제거특성을 보인 반면 그 이상에서는 불안정한 제거특성을 나타내면서 제거효율이 감소하였다. TOCs의 경우에는 부하량 변화에 따른 처리효율 변화는 관찰되지 않았으며, 그 제거효율은 수처리 시간에 의존적인 것으로 나타났다 ($r^2$ = 0.97). 색도 제거 효율은 전기분해조 용적기준 수처리시간 2일 이상에서 94%의 매우 높고 일정한 효율을 얻을 수 있었다.

• 한국환경과학회지
• /
• 제12권10호
• /
• pp.1085-1093
• /
• 2003

This study was conducted to investigate anoxic-RBC (rotating biological contactor) and its application in advanced municipal wastewater treatment process to remove biologically organics and ammonia nitrogen. Effluent COD and nitrogen concentration increased as the increase of volumetric loading rate. But, the concentration changes of NO$_2$$\^$-/ -N and NO$_3$$\^$-/ -N were little, as compared to COD and NH$_4$$\^$+/ -N. When the volumetric loading rate increased, COD removal efficiency and nitrification appeared very high as 96.7∼98.8% and 92.5∼98.8%, respectively. However, denitrification rate decreased to 76.2∼88.0%. These results showed that the change of volumetric loading rate affected to the denitrification rate more than COD removal efficiency or nitrification rate. The surface loading rates applied to RBC were 0.13～6.0lg COD/㎡-day and 0.312∼1.677g NH$_4$$\^$+/-N㎡-day and they were increased as the increase of volumetric loading rate. However, the nitrification rate showed higher than 90%. The thickness of the biofilm in RBC was 0.130 ∼0.141mm and the density of biofilm was 79.62∼83.78mg/㎤. They were increased as surface loading rate increased. From batch kinetic tests, the k$\_$maxH/ and k$\_$maxN/ were obtained as 1.586 g C/g VSS-day, and 0.276 g N/g VSS-day, respectively. Kinetic constants of denitrifer in anoxic reactor, Y, k$\_$e/, K$\_$s/, and k were 0.678 mg VSS/mg N, 0.0032 day$\^$-1/, 29.0 mg N/l , and 0.108 day$\^$-l/, respectively. P and K$\_$s/, values of nitrification and organics removal in RBC were 0.556 g N/㎡-day and 18.71 g COD/㎡-day, respectively.

• 한국자동차공학회논문집
• /
• 제15권3호
• /
• pp.72-78
• /
• 2007

A diesel particulate filter causes progressive increase in back pressure of an exhaust system due to the loading of soot particles. To maintain the pressure drop caused by DPF under proper level, a regeneration process is mandatory when excessive loading of soot is detected in the filter. It is a major reason why the relation between the amount of soot and the pressure drop in a DPF becomes crucial. On the other hand, pressure drop varies with not only the soot loading but also conditions of exhaust gas such as mass flow rate. Therefore, the relation among them becomes complicated. Furthermore, the characteristics of heat transfer in a DPF is another crucial parameter in order for the filter to avoid thermal crack during regeneration period. This study presents characteristics of pressure drop under various conditions of soot loading and mass flow rate in catalyzed diesel particulate filter. This study also shows characteristics of heat transfer in DPF when high temperature gas flows into the filter. Experiments reveal that the soot loading and mass flow rate affect characteristics pressure drop independently. Experiments also indicate that the amount of coating material has little influence on pressure drop with changes in soot loading and mass flow rate. However, increased catalyst coating may lead to the improved heat transfer which is efficiency to reduce thermal stress of the filter.

• 한국지반신소재학회논문집
• /
• 제22권3호
• /
• pp.97-103
• /
• 2023

최근 말뚝기초의 수평저항력에 대한 연구들이 활발히 이루어지고 있다. 말뚝기초의 수평저항력에 대한 실험연구들의 경우 변위제어법 또는 하중제어법을 사용하고 있다. 하지만 변위제어법의 경우 말뚝에 가해지는 하중의 속도에 따라 말뚝의 수평저항력이 달라진다. 따라서 본 연구에서는 모형실험을 통해 수평재하속도에 따른 말뚝기초의 수평저항력 변화를 파악하고자 한다. 실험결과 말뚝두부에 가해지낸 수평재하속도가 빠를수록 말뚝의 수평저항력이 감소하는 경향을 보였다. 이를 확인하기 위해 재하속도에 따른 지반과 말뚝의 측면변경 모형실험을 추가적으로 진행하였으며, 그 결과 재하속도가 빠를수록 말뚝의 회전절점의 깊이가 감소하였다. 역해석을 통해 수평재하 속도에 따른 회전절점의 깊이 변화를 파악하였다. 수평재하속도에 따른 말뚝기초의 수평저항력과 회전절점의 깊이 변화를 통해, 말뚝의 수평재하시험시 재하속도는 1.5mm/min 이내로 시험하는 것을 제안하였다.

• 한국세라믹학회지
• /
• 제39권12호
• /
• pp.1149-1152
• /
• 2002

실리콘의 고압상을 연구하는 수단으로 압입 방법을 사용하였다. 실험에는 (100)과 (111) 실리콘 웨이퍼를 사용하였으며 하중유지 시간과 하중인가 속도에 따른 잔류상의 변화를 연구하였다. 압입 후의 상분석에는 Raman spectroscopy를 사용하였다. 하중 유지 시간의 실험결과 (111) 시편에서는 하중 유지 시간이 길어질수록 소성변형이 진행되어 고압상인 Si-III 와 Si-XII는 결정구조를 유지하지 못하고 사라지고 대신 a-Si가 관찰되었다. 하중 인가 속도 실험 결과 하중 인가 속도가 0.1 mm/min일 경우 모든 시편의 force/displacement 곡선에서 pop-in을 관찰할 수 있었다. Raman peak 분석 결과 이들 시편에서는 상전이가 관찰되었다. 5 mm/min의 하중인가 속도의 경우 (111) 시편에서는 급격한 변형의 증가 부분이 관찰되었으나 (100) 시편의 경우 관찰되지 않았다. 하중인가 속도가 느릴 경우 상전이 양상이 뚜렷하게 나타났으며 반대의 경우 상전이는 소량 관찰되거나 관찰되지 않았다. 이것은 하중인가속도가 상전이 영역의 부피에 영향을 주기 때문이라 판단된다.

• Computers and Concrete
• /
• 제33권5호
• /
• pp.519-533
• /
• 2024

Many materials including cementitious concrete-type materials undergo material property changes during high-rate loading. There is a wealth of research regarding this phenomenon for concrete in compression and tension. However, there is minimal knowledge about how mortar material used in concrete masonry unit (CMU) construction behaves in high-rate shear loading. A series of experiments was conducted to examine the bond strength of mortar bonded to CMU units under high-rate shear loading. A novel experimental setup using a shock tube and dynamic ram were used to load specially constructed shear triplets in a double lap shear configuration with no pre-compression. The Finite Element Method was leveraged in conjunction with data from the experimental investigation to establish if the shear bond between concrete masonry units and mortar exhibits any rate dependency. An increase in shear bond strength was observed when loaded at a high strain rate. This data indicates that the CMU-mortar bond exhibits a rate dependent strength change and illustrates the need for further study of the CMU-mortar interface characteristics at high strain rates.

• 한국물환경학회지
• /
• 제28권1호
• /
• pp.109-114
• /
• 2012

In this study, both sedimentation and thickening experiments were conducted for residuals produced from an advanced water treatment plant for more accurate and practical design of residual treatment train. In order to design a backwashed residual sedimentation basin (SRSB) in the filter backwash water recycle system, two kinds of backwash waters, one from sand filter (SFBW) and the other from GAC adsorption bed (GACBW), were separately collected and their surface loading rate measured. In addition, in order to design a gravity thickener, batch thickening tests were conducted for concentrated residuals taken from sedimentation basin and their limiting solid flux ($SF_{L}$) measured. From the experimental results and consideration of the seasonal characteristics of the residual, surface loading rate of $70m^{3}/m^{2}{\cdot}d$ was proposed as a design parameter for SRSB and solid loading rate of 20 kg $TS/m^{2}{\cdot}d$ was proposed as a design parameter for gravity thickeners. Finally, the material mass-balance was made for the design of each unit process in the residual treatment train.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1998년도 가을 학술발표논문집(II)
• /
• pp.468-473
• /
• 1998

The objective of this paper is to develop a consistent algorithm for the finite element analysis for behavior of concrete under cyclic loading using viscoplastic-damage model. For modeling the behavior of concrete under cyclic loading, consistent algorithms of rate-dependent viscoplastic-damage are employed with a Willam-Warnke 5-parameter failure criterion which can consider the softening behavior of concrete and consistent tangent moduli are derived. Using finite element program implemented with the developed algorithms, the algorithms are verified and the behaviors of concrete under cylic loading are simulated and compared with experimental data.