• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2012년도 제38회 춘계학술대회논문집
• /
• pp.331-341
• /
• 2012

고에너지 물질의 연소 현상을 해석하기 위하여 반드시 필요한 반응속도식과 이를 구성하고 있는 미정상수를 결정하는 이론적 방법을 제안하였다. 개선된 I&G 모델은 기존의 반응속도식이 갖던 문제점들을 효과적으로 극복하면서 동시에 중요한 물리적 의미를 내포하는 형태로 제안되었다. 이는 공극붕괴(void collapse)로 인한 hotspot의 생성을 의미하는 점화 모델과 폭굉(detonation)으로의 천이를 의미하는 화염 발달 모델의 합으로 구성되어 있다. 또한 함께 소개된 이론적 모델은 고에너지 물질의 수치해석 기법인 Hydrocode를 사용하기 전에 미정상수 b, G, x, I를 결정함으로써 특정 고에너지 물질의 연소 특성을 규명하는데 사용된다. 이론적 방법은 기존의 고에너지 물질의 연소 시험을 모사한 수치해석적 방식보다 효율적이고 정확도가 높은 결과를 제공하므로 진일보 된 방법이라고 할 수 있다.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 2000년도 제31회 춘계학술대회
• /
• pp.263-268
• /
• 2000

The fretting damage of the contact between Zircaloy-4 and Inconel 600 have Investigated. A fretting wear tester was designed to be suitable for this fretting test. In this study, the number of cycles, slip amplitude and normal load were selected as main factors of fretting wear. As the result of this research the wear volume increased with the increase of loads, slip amplitudes and the number of cycles and was more affected by slip amplitudes rather than by load. According to SEM, stick, partial slip, gross slip were observed on the surface of both specimens and wavy worn surfaces as the typical fretting damage were also Investigated due to accumulation of plastic flow.

• 한국안전학회지
• /
• 제18권4호
• /
• pp.71-77
• /
• 2003

To inject fresh air into a fire room, Positive Pressure Ventilation (PPV) can be used and the blower of PPV increases inside pressure of the room. It makes high flow rate of products of combustion, smoke and heat from the structure, and it is very helpful to fireman on the fire extinguishing work. The flame moves to the direction of airflow and the temperature of flame can be decreased rapidly. In this experiment, a water mist system is applied to PPV to increase the effectiveness, and various effective factors are studied. n-Heptane and pine wood stick were used as fuel. Temperatures at the above and behind the combustion pan were strongly reduced by the water mist system and by the convective cooling with airflow. The smoke density was also decreased by PPV with water mist system and it can be explained by the absorption of smoke particles on the water mist droplet and by the strong exhausting effects of mobile fan.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1990년도 추계학술대회 논문집
• /
• pp.36-38
• /
• 1990

In this study, a new sintered specimens of Y$\_$1-x/Sm$\_$x/Ba$_2$Cu$_3$O$\_$y/ is composed by substituting Sm for a part of Y in the YBa$_2$Cu$_3$O$\_$y/ high Tc superconductor, in order to study of making (Y$.$Sm)-Ba-Cu-O system sintered specimens and their characteristics. An their change affected on superconductivity and their characteristics are studied by changing the x range of the composition rate. The resistances of electrical characteristics under the conditions of the composition and the temperature are measured by using Ac four probe method in the procedure of this experiments. And it is confirmed that the Meissner effect from the superconductivity of composed Sm system exists in the range of 0

• Tribology and Lubricants
• /
• 제17권5호
• /
• pp.380-385
• /
• 2001

In nuclear power steam generators, high flow rates can induce vibration of the tubes resulting in fretting wear damage due to contacts between the tubes and their supports. In this paper the fretting wear tests and the sliding wear tests were performed using the steam generator tube materials of Inconel 600 and 690 against STS 304. Sliding tests with the pin-on-disk type tribometer were done under various applied loads and sliding speeds at air environment. Fretting tests were done under various vibrating amplitudes and applied normal loads. From the results of sliding and fretting wear tests, the wear of Inconel 600 and 690 can be predictable using the work rate model. Depending on normal loads and vibrating amplitudes, distinctively different wear mechanisms and often drastically different wear rates can occur. It was found the results that the wear coefficients for Inconel 600 and 690 were 262.3$\times$10$\^$-15/Pa$\^$-1/ and 209.2$\times$10$\^$-15/Pa$\^$-1/, respectively. This study shows that Inconel 690 can provide much better wear resistance than Inconel 600 in air.

• 한국안전학회지
• /
• 제14권4호
• /
• pp.114-119
• /
• 1999

When NaOCl was generated and put into sea-water cooling machine in order to overcome the biological hindrances against sea-water cooling machine, it was converted into metallic ion, particularly Ca and Mg, as a hydrate in sea-water and is to stick to electrolyte as a side reaction. This phenomena make the distance between the electrolytes narrow to decrease the flow rate, which induces the local vortex flow which erodes the pole plate. Moreover, this increases the resistance of the electrolyte as well as voltage to decrease the electrolytic efficiency, which has curtailed a chlorine yield and caused a pole plate cut. We are able to overcome these problems by chemical cleaning and intend to extend the life-time of electrolyte and to increase output of the sea-water electrolysis facilities by studying optimal policy regarding chemical cleaning of electrolytic cell. Cleaning time of electrolytic facilities is determined when both increase in electrolytic efficiency and decrease in pole-plate voltage are 10%. At this time as operating current of electrolytic facilities is high, operating time is diminished. Whereas, parameter of end point determination according to cleaning is Mg ionic concentration in solution. When we use Cleaner as a 7wt% HCl, cleaning time is about 80min proper. We are able to maintain pole plate performance by protecting against pole plate cut by means of electrolytic by-product, improve operating rate of facilities, and cut down on maintenance expenditure after acidic cleaning.

• Tribology and Lubricants
• /
• 제30권3호
• /
• pp.168-176
• /
• 2014

This paper presents an engine oil change warning algorithm based on the test results of a small dip-stick-gage-type engine-oil-deterioration-detection sensor, software to realize the algorithm and a display device to apply the software. The algorithm determines the engine oil deterioration condition from the rate of change in the dielectric constant based on the average measured capacitance at $80^{\circ}C$ after the engine stops. The rate of change in the dielectric constant at the time for oil change correlates with the time that one of recommended warning limits for engine oil physical properties such as TAN (Total Acid Number), TBN (Total Base Number) and viscosity is first reached. At this point, a warning signal for oil change appears on the display device like a smart-phone or individual display device. The frames of smartphone app have three stages. The user can directly input all of the thresholds into the frame of the smartphone app. The screen of the display device comprises one frame for each warning signature with the related message. The user can input the thresholds to the device through a USB cable connected to a personal computer.

• 한국자동차공학회논문집
• /
• 제6권4호
• /
• pp.86-100
• /
• 1998

The impingement of the fuel spray on the wall within the combustion chamber in compact high-pressure injection engines and on the intake port wall in port-fuel-inje- ction type engines is unavoidable. It is important to understand the characteristics of impinging spray because it influences on the rate of fuel evaporation and droplet distrib- ution etc. In this study, the numerical study for the characteristics of spray/wall interaction is performed to test the applicability and reliability of spray/wall impingement models. The impingement models used are stick model, reflect model, jet model and Watkins and Park's model. The head of wall-jet eminating radilly outward from the spray impingement site contains a vortex. Small droplets are deflected away from the wall by the stagnation flow field and the gas wall-jet flow. While the larger droplets with correspondingly higher momentum are impinged on the wall surface and them are moved along the wall and are rolled up by wall-jet vortex. Using the Watkins and Park's model the predicted results show the most reasonable trend. The rate of increase of spread and the height of the developing wall-spray is predicted to decrease with increased ambient pressure(gas density).

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2017년도 제48회 춘계학술대회논문집
• /
• pp.617-621
• /
• 2017

본 연구에서는 Al 입자가 함유된 고폭약의 성능 특성을 2 상 모델(two-phase model)을 이용하여 수치 해석을 수행하였다. Al 입자의 점화와 연소시간은 고폭약에 비해 상대적으로 긴 시간이 요구되기 때문에, Al 입자연소에 의한 에너지 발산은 고폭약의 데토네이션 후방에서 이루어진다. Al 입자를 함유하는 고폭약은 Al 함유량이 증가함에 따라 데토네이션 속도의 감소와 고폭약 데토네이션 후방에서 Al 입자 연소가 일어나며 이중 데토네이션이 관찰되는 특징이 있다. 본 연구에서는 Al 입자가 함유된 HMX의 데토네이션 특성을 재현하기 위해 최대 Al 함유량 50%를 갖는 confined rate stick이 고려되었으며, 수치해석 결과는 5-25% 함유량에 대한 실험결과와 비교되었다.

• 한국미생물·생명공학회지
• /
• 제13권4호
• /
• pp.409-415
• /
• 1985

시판 어육연제품의 보장성과 식품위생학적인 기초자료를 얻고자 1984년 5월부터 10월사이에 연제품 가공공장과 수퍼마켓등에서 구입한 게맛살, 판어묵, 부들어묵, 튀김어묵 및 어육소시지등 5종총 70점의 시료를 대상으로 세균학적 품질, 세균특징별 분포, 내열성세균의 배양적 세균학적 특성에 관하여 조사한 결과는 다음과 같다. 1. 가열후에 포장하는 부들어묵과 튀김어묵은 위생지표세균 및 효모와 곰팡이의 오염이 대체로 높았으며, 가열전에 포장하는 게맛살과 판어묵은 세균학적으로 매우 깨끗하였다. 포도상구균은 튀김어묵에서만이 검출되었으며, Salmonella균은 모든 제품에서 검출되지 않았다. 가공공장 시료에서 연제품 가공공정중 열처리전의 게맛살과 판어묵 시료중에 호기성 및 염기성균이 $10^{6}$-$10^{7}$ g으로 함량이 높았으나, 열처리직후의 제품은 호기성균이 ＜$10^2$/g 이었으며 염기성균은 검출되지 않았다. 그리고 어육소시지에서는 전혀 세균이 검출되지 않았다. 2. 분리된 세균중 단백질분해능이 있는 세균의 분포는 대부분의 시료에서 87% 이상으로 높았고, 지방분해능이 있는 세균의 분포는 20%미만이었다. 3. 분리된 세균에 대한 Gram 염색결과는 게맛살과 판어묵에서는 Gram양성균이 70%이상이었고 튀김어묵에서는 47.3%이었으며, 형태별로는 간균이 분리균주의 90%이상을 차지하였다. 4. 분리균중 내열성이 제일 강한 균주는 Bacillus licheniformis CR-11이었는데, 단백질분해능이 있을 뿐 아니라 2$0^{\circ}C$이상에서는 발육이 양호하였으며 또한 염기적 조건에서도 발육이 좋았다. 5. CR-11 균주의 배양온도별 비증식속도와 평균세대시간은 2$0^{\circ}C$에서 각각 0.31$hr^{-1}$, 2.24hr, 3$0^{\circ}C$에서 0.64$hr^{-1}$, 1.09hr, 그리고 35$^{\circ}C$에서는 0.78$hr^{-1}$, 0.89hr이었고, 포자의 내열성은 D$_{85}$ $^{\circ}C$=41.9min, D$_{90}$ $^{\circ}C$=27.9min, D$_{95}$ $^{\circ}C$=10.2min, D$_{100}$ $^{\circ}C$=4.3min이었으며, Z-value는 13.8$^{\circ}C$이었다.