• Journal of Korean Society of Environmental Engineers
• /
• v.30 no.11
• /
• pp.1139-1145
• /
• 2008

The objectives of this research are to investigate the mechanism of coagulation affecting UF and find out the optimum conditions of the combined of coagulation with UF membrane filtration for NOM removal. During the mixing period, substantial changes in particle size distribution occurred under rapid and slow mixing condition due to the simultaneous formation of microflocs and NOM precipitates. Therefore, combined pretreatment using coagulation (both rapid mixing and slow mixing) improved dissolved removal efficiency. Also, for combined coagulation to membrane process, flux reduction rate showed lower than only UF process. The rate of flux decline for the hydrophobic membrane was considerably greater than for the hydrophilic membrane. Applying coagulation process before membrane filtration showed not only reducing membrane fouling, but also improving the removal of dissolved organic materials that might otherwise not be removed by the membrane.

• Food Science of Animal Resources
• /
• v.35 no.4
• /
• pp.466-472
• /
• 2015

A rapid and simple analytical method, using liquid chromatography tandem mass spectrometry (LC-MS/MS), was developed to detect myo-inositol (MI) in infant formulas. For protein removal: acid hydrolysis and lipid removal through organic solvent extraction. The operating conditions for instrumental analysis were determined based on previously reported analogous methods that used LC-MS/MS. Quantitative analysis was used for the detection limit test, infant formula recovery test, and standard reference material (SRM) 1849a to verify the validity of our LC-MS/MS analytical method, which was developed to quantify MI. For validation, the results of our method were compared with the results of quantitative analyses of certified values. The test results showed that the limit of detection was 0.05 mg/L, the limit of quantitation was 0.17 mg/L, and the method detection limit was 17 mg/kg. The recovery test exhibited a recovery between 98.07-98.43% and a relative standard deviation between 1.93-2.74%. Therefore, the result values were good. Additionally, SRM 1849a was measured to have an MI content of 401.84 mg/kg and recovery of 98.25%, which is comparable to the median certified value of 409 mg/kg. From the aforementioned results, we judged that the instrumental analysis conditions and preparation method used in this study were valid. The rapid analytical method developed herein could be implemented in many laboratories that seek to save time and labor.

• Journal of Korean Society of Water and Wastewater
• /
• v.21 no.3
• /
• pp.359-366
• /
• 2007

Slow sand filtrations have been widely used for water treatment in small communities, however their capacity is often limited by high turbidity in the raw water. For this reason, several pre-treatment facilities were required for a slow sand filter. Turbidity removal from the highly turbid raw water was investigated in roughing filters as a pre-treatment process. The roughing filters followed by rapid mixing tank were operated in the form of a contact filtration. In several jar tests, the predetermined optimum aluminium sulfate (alum) doses for turbid water of 30 and 120NTU were 30 and 50mg/L, respectively. At the optimum alum dose, physically optimum parameters including G value of $220sec^{-1}$ and rapid mixing time of 3 minutes were applied to the contact filtration system. Without addition of alum, the filtrate turbidity from the roughing filters, packed respectively with different media such as sand, porous diatomite ball and gravel, was in the range of 5~30NTU at filtration velocities of 30 and 50m/day. However, the application of a contact filtration to roughing filters showed stably lower filtrate turbidity below 1.0NTU at filtration velocity of 30 m/day. Although the filtration velocity increased to 50m/day, filtrate turbidity was still below 1.0NTU in both single and double layer roughing filters. At influent turbidity of 120NTU, the filtrate turbidity was over 5 NTU in the triple layer roughing filter, which shortened the filter run time. The flocs larger than $10{\mu}m$, formed in the rapid mixing tank, were almost captured through the roughing filter bed, while the almost flocs smaller than $10{\mu}m$ remained in filtrate.

• KSBB Journal
• /
• v.23 no.6
• /
• pp.484-488
• /
• 2008

Chlorinated phenols are widely used by the chemical industry as intermediate products in synthesis and previously were frequently applied to various industry fields. Peroxidases catalyze the peroxide-dependent oxidation of a range of inorganic and organic compounds. Peroxidase was shown to mineralize a variety of recalcitrant aromatic compounds and to oxidize a number of polycyclic aromatic and phenolic compounds. Among monomeric phenolic and nonphenolic compounds, peroxidase is known to oxidize its compounds. In this study, a colorimetric assay was developed to quantitatively evaluate the peroxidase activity for rapid screening. Color products of different intensity were developed proportionally to the peroxidase activity on agar plate and 96-well plate. This method correlates well with the RP-HPLC result. Using this screening method, 12 colonies of strain was screened which survived at high concentration of 2,4-DCP (1000 ppm) and with peroxidase activity for the $7^{th}$ round screening step on agar plate. These strains were utilized 2,4-DCP as a sole carbon source and produced peroxidase. After the screening test, four of the bacteria have significant better effect of COD removal on dye waste-water. COD removal of these was from 44% to 61%, respectively.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.24 no.8 s.179
• /
• pp.1958-1967
• /
• 2000

Rapid Prototyping( RP ) has been increasingly applied in the process of design and development of new products. RP can shrink the time and expense required to bring a new product from initial concept to production. However, the necessity of using RP for short-run manufacturing is continuously driving a development of a cost-effective technique that will produce completely-finished quality parts in a very short time. To meet these demands, the improvements in production speed, accuracy materials, and cost are crucial. Thus, a new hybrid-RP system performing both deposition and machining in a station is proposed in this paper. It incorporates both material deposition in layers and material removal from the outer surface of the layer to produce the required surface finish. The new hybrid-RP system can dramatically reduce the total build time and fabricate largo-sized and freeform objects because it uses very thick layers, i.e.

• Journal of Korean Neurosurgical Society
• /
• v.54 no.5
• /
• pp.426-430
• /
• 2013

The prognosis of solitary plasmacytoma varies greatly, with some patients recovering after surgical removal or local fractional radiation therapy, and others progressing to multiple myeloma years later. Primary detection of progression to multiple myeloma is important in the treatment of solitary plasmacytoma. There have been several analyses of the risk factors involved in the early progression to multiple myeloma. We describe one case of solitary plasmacytoma of the lumbar vertebra that was treated with surgical decompression with stabilization and additional radiotherapy. The patient had no factors associated with rapid progression to multiple myeloma such as age, size, immunologic results, pathological findings, and serum free light chain ratio at the time of diagnosis. However, his condition progressed to multiple myeloma less than two months after the initial diagnosis of solitary plasmacytoma. We suggest that surgeons should be vigilant in watching for rapid progression to multiple myeloma even in case that the patient with solitary plasmacytoma has no risk factors for rapid progression to multiple myeloma.

• Korean Journal of Animal Reproduction
• /
• v.13 no.3
• /
• pp.141-148
• /
• 1989

The effects of seeding method and optimum time for freezing embryos according to the developmental stages on embryo survival rates after rapid freezing were determined using the FDA-test. The summarized results are as follows : 1. In the rapid freezing of embryos, the sucrose added medium together with Co-seeding or non-seeding showed the FDA scores of 4.67 and 4.20, respectively, but, raffinose addition obtained FDA scores of 4.27 and 3.97. 2. The developmental stage of embryos at freezing was most critical on the survival of embryos after thawing. Higher FDA scores were obtained in the order of blastocyst stage(4.94), morula stage(3.82) and ealy stage(2.65) in sucrose added medium. The same trend was observed in the raffinose added medium with an order or 4.91, 4.47 and 2.32. 3. Microscopic study of embryo before freezing and post-thawing indicated that the embryo showed shrinkage within 5 minutes after the embryo was transfer to the freezing medium. When thawed embryo was tranfered to the dilution medium, swelling of the embryo was observed and there after it reshrank indicating the removal of cryoprotectant from the embryo. The size of the embryo recovered to the original state when it was moved into a PBS-solution.

• Journal of Korean Society on Water Environment
• /
• v.33 no.5
• /
• pp.572-579
• /
• 2017

Increased impervious surface caused by rapid urbanization serves to produce the discharge of non-point source pollutants such as total suspended solid (TSS). There exist various methods of removing TSS, including a filtration process using granular media (a well-known method to be practically used after the consideration of removal efficiency, clogging, and backwashing efficiency). To determine the TSS removal capability of the filter, we initially performed lab-scale experiments which assessed flow rates, influent concentrations, permeability co-efficients, the particular shapes of suspended solids and potential clogging, and also evaluated TSS removal efficiency when applied to filtration facility in a pilot-scale. In low filtration flux condition, the removal efficiency of suspended solids was more than 95 %, while decreased to 83% in high filtration flux. Regarding the clogging aspect of the experiment, total cumulative solids were loaded up to $19.15kg/m^2$, and TSS removal efficiency was noted to commence to decrease when the loaded solids exceeded $9.0kg/m^2$. It was also noted, however, that superior efficiency was maintained for six hours. In addition, for pilot-scale experiment, the removal efficiency was still high enough (83.4 %) for the solid concentration of 140 ~ 343 mg SS/L and after backwashing, head loss was recovered to 92 ~ 95 % during two hour filtration. With these results, It was confirmed that lifetime of the filter applied to the test was prolonged due to the high treatment efficiency and good backwashing efficiency for the cumulative solids load.

• Journal of Korean Society of Environmental Engineers
• /
• v.34 no.2
• /
• pp.73-78
• /
• 2012

In this study, three different synthetic musk compounds (SMCs) in the Nakdong river water (raw water) and rapid sand filtered water were treated by $O_3$ process. The experimental results showed that the removal efficiency of musk ketone (MK) was lower than removal efficiency of AHTN (7-acetyl-1,1,3,4,4,6-hexamethyl-1,2,3,4-tetrahydronaphthalene) and HHCB (1,3,4,6,7,8-hexahydro-4,6,6,7,8,8-hexamethylcyclopenta[c]-2-benzopyran) for both the raw water and the rapid sand filtered water. And in general, the removal efficiencies of three SMCs in the raw water were lower than that in the sand filtered water. Under the $O_3$ dose of 0.5~10.0 mg/L, the removal rate constants (k) of three SMCs for the raw and sand filtered waters increased rapidly with the increased $O_3$ dose. In the case of drinking water treatment plants (DWTPs) which were selected pre- and post-$O_3$ processes (located in the downstream of Nakdong River), operation conditions of pre- and post-$O_3$ process were $0.5{\sim}2.0mg{\cdot}O_3/L$ (2~4 min) and $0.5{\sim}2.5mg{\cdot}O_3/L$ (6~8 min). Therefore, $O_3$ doses and contact times of same conditions with above were very difficult to remove SMCs in DWTPs.

• Proceedings of the Korean Society of Soil and Groundwater Environment Conference
• /
• 2002.04a
• /
• pp.13-17
• /
• 2002

Ultrasonic waves have several mechanical, chemical, and biological effects on a saturated soil medium. Their mechanical effects, popularly known as cavitation. Cavitation is the rapid and repeated formation, and resulting implosion, of imcrobubbles in a liquid, resulting in the propagation of microscopic shock waves. In a soil-liquid system, their mechanical effects generate high differntial fluid-particle velocities and microscopic shock waves. The velocity perturbations are capable of dislodging oil in the system by overcoming the forces binding oil to sand particles. In this study, a series of laboratory experiments involving the simple flushing and ultrasonic flushing were carried out. An increase in permeability and oil removal rate were observed in ultrasonic flushing tests. Some practical implications of these results are discussed in terms of technical feasibility of in situ implementation of ultrasonics.