• 한국환경과학회지
• /
• 제25권2호
• /
• pp.231-238
• /
• 2016

In this study, we have investigated to find optimal pre-treatment flocculation condition by analyzing the floc growth rate with mixing conditions and the membrane permeation flux for pre-treatment step of the membrane process. The higher mixing intensity showed a constant floc size index (FSI) values, and lower mixing intensity increased the degree of dispersion of the FSI values. Results of comparing the distribution characteristics of the FSI value and the permeation flux were more effective in increasing flux when the FSI values were 0.2 or higher. The degree of dispersion of FSI was relatively large in 40 rpm mixing condition compared to 120 rpm. In 40 rpm mixing condition, it decreased the permeation flux compared to 120 rpm because various sizes of flocs were distributed. Coagulation-UF membrane process enhanced 30%~40% of the flux rate compare to UF alone process, and the coagulation-MF process increased up to 5% of the flux rate compare to MF alone process. Pre-treatment, that is, coagulation process, has been found to be less effects on relatively larger pore size for MF membrane. For UF membrane, the flux was a little bit same when applying only the rapid mixing process or rapid mixing with slow mixing processes together. In case of MF membrane, the flux was improved when rapid mixing process applied with slow mixing process together.

• 한국도로학회논문집
• /
• 제17권3호
• /
• pp.85-95
• /
• 2015

PURPOSES : Recently, bonded concrete overlay has been used as an alternative solution in concrete pavement rehabilitation since its material properties are similar to those of the existing concrete pavements. Deteriorated concrete pavements need rapid rehabilitation in order to prevent traffic jams on Korean expressways. Moreover, speedy and effective repair methods are required. Therefore, the use of bonded concrete overlay with ultra-rapid hardening cement has increased in an effort to reopen promptly the expressways in Korea. However, mobile mixer is required for ultra-rapid hardening cement concrete mixing in the construction site. The use of mobile mixer causes various disadvantages aforementioned such as limitation of the construction supply, open-air storage of mixing materials, increase in construction cost, and etc. In this study, therefore, hydration accelerator in-situ mixing on polymer modified concrete produced in concrete plant is attempted in order to avoid the disadvantages of existing bonded concrete overlay method using ultra-rapid hardening cement. METHODS : Bonded concrete overlay materials using ultra-rapid hardening cement should be meet all the requirements including structural characteristics, compatibility, durability for field application. Therefore, This study aimed to evaluate the application of hydration accelerator in-situ mixing on polymer modified concrete by evaluating structural characteristics, compatibility, durability and economic efficiency for bonded concrete overlay. RESULTS : Test results of structural characteristics showed that the compressive, flexural strength and bond strength were exceed 21MPa, 3.15MPa and 1.4MPa, respectively, which are the target strengths of four hours age for the purpose of prompt traffic reopening. In addition, tests of compatibility, such as drying shrinkage, coefficient of thermal expansion and modulus of elasticity, and durability (chloride ions penetration resistance, freezing-thawing resistance, scaling resistance, abrasion resistance and crack resistance), showed that the hydration accelerator in-situ mixing on polymer modified concrete were satisfied the required criteria. CONCLUSIONS : It was known that the hydration accelerator in-situ mixing on polymer modified concrete overlay method was applicable for bonded concrete overlay and was a good alternative method to substitute the existing bonded concrete overlay method since structural characteristics, compatibility, durability were satisfied the criteria and its economic efficiency was excellent compare to the existing bonded concrete overlay methods.

• 펄프종이기술
• /
• 제33권3호
• /
• pp.44-51
• /
• 2001

Sedimentation characteristics such as SS, $BOD_5$, COD removal efficiency of waste water in the toilet paper mill using milk carton were examined. Optimum dosage of coagulant, rapid mixing time and slow mixing time were determined by turbidity, SS, COD, $BOD_5$ and then equation for treatment efficiency was suggested. Mechanical strength of floc was determined by turbidity. For the coagulant, polyacrylamide (PAM) is more efficient for removing pollution than the aluminium sulfate. Effective mixing ratios of PAM and aluminum sulfate to remove pollution are 70:30 and 30:70. The lowest turbidity was showed when rapid mixing at 300 rpm after coagulant injection was applied. That which indicates the highest point of flocs mechanical strength.

• 환경위생공학
• /
• 제10권2호
• /
• pp.30-35
• /
• 1995

In this research effect of physicochemical parameter on flocculation using PASS-100 were evaluated. pEt flocculant dosage, mixing intensity and detention time were adopted as experimental variables. The physicochemical parameter( p% mixing intensity and mixing time ) were important Parameter on flocculation performance. Effluent pH range for effective flocculation was 4.5-7. Optimum Gt$_{d}$ range was 20,000-30,000 and its range similar to alum flucculation. Rapid mixing was very important parameter to floe formation in PASS- 100 flocculation. Whereas, slow mixing did not affect to the removal efficiency at settling time for 30minute or more.

• 대한환경공학회지
• /
• 제38권3호
• /
• pp.150-153
• /
• 2016

본 연구는 $TiCl_4$의 농도(0.25-0.59 mM)와 급속교반속도(100-250 rpm), 완속교반속도(30-60 rpm)의 변화가 인 제거효율에 미치는 영향을 알아보고자 하였다. 응집제 농도가 $0.25{\leq}[TiCl_4]{\leq}0.39mM$ 범위에서 인 제거 효율은 $TiCl_4$의 농도가 증가 할수록 증가하였으며 처리후 인의 농도는 0.2 mg/L 이하였다. 응집제 농도 0.39 mM, 급속교반속도 100 rpm, 완속교반속도 30 rpm에서 인 제거효율이 약 99%로 가장 높았다. $TiCl_4$의 농도가 낮을 경우(0.25-0.27 mM) 인제거효율의 편차는 급속교반속도 변화(2-3%)보다 완속교반속도 변화(7-10%)에서 더 민감하였다.

• 한국연소학회:학술대회논문집
• /
• 한국연소학회 2006년도 제33회 KOSCO SYMPOSIUM 논문집
• /
• pp.122-127
• /
• 2006

The objective of this research is to determine generally applicable design principles for the development of Rapid mix burner. Details operating RMB(Rapid mix burner) is designed that thermal NOx and prompt NOx formation be reduced through control of low peak flame temperature, and nearly uniform flame temperature by rapid mixing at the ignition point. Results from RMB(Rapid mix burner) achieving lower than 43 ppm NOx emissions and nearly flame temperature uniform

• 대한기계학회논문집A
• /
• 제29권5호
• /
• pp.707-715
• /
• 2005

In this work, Scalar Passive code in Lattice Boltzmann Method is employed to simulate two-phase flow of low Reynolds number in a micro-channel. The mixing characteristics in a micro-channel is a function of Peclet number. The mixing length increases with the Peclet number. It is found that with the inclusion of static elements at the channel, rapid mixing of two liquids can be achieved, as shown by the results of computer simulations. The enhancement in mixing performance is thought to be caused by the generation of eddies and by lateral velocity component when the mixture flows past static elements. The results indicate that the size of static element has more effect on the mixing than the number of static element.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2001년도 The 6th International Symposium of East Asian Resources Recycling Technology
• /
• pp.715-718
• /
• 2001

This study uses traditional alum coagulation and sedimentation process to treat CMP wastewater from cleaning after polishing. The primary goal is to successfully recycle both solid fines and water for semiconductor manufacturing. Results indicated that CMP wastewater may be successfully treated to recover clean water and fine particles by alum coagulation. The optimum operating conditions for coagulation are as fellowing: alum dosage of 10 ppm, pH at 5, rapid mixing speed at 800 rpm, 5 min rapid mixing time, and long slow mixing time. The treated water with low turbidity and an average residual aluminum ion concentration of 0.23 ppm may be considered for reuse. The settled sludge after alum coagulation contains mainly SiO$_2$particle with a minor content of aluminum (1.7 wt%) may be considered as raw materials for glass and ceramic industry.

• 유체기계공업학회:학술대회논문집
• /
• 유체기계공업학회 2006년 제4회 한국유체공학학술대회 논문집
• /
• pp.309-312
• /
• 2006

Effective mixing is an important problem in microfluidics for chemical and biomechanical applications. In this study, the influences of the Reynolds number and the oscillating frequency on mixing characteristics of micro-stirrer are studied in a microchannel with single stirrer. The influence of fluid inertial effects in an active mixer is first discussed. It is found that the stirring effects by stirrer oscillation are promptly attenuated at low Reynolds number, which makes greatly difficult the rapid mixing. As the inertial effects are increased, the chaotic advection is generated and then developed. The mixing phase is finally developed some mushroom shaped structure. And the mixing efficiency is also studied as a function of the oscillating frequency. We found that the mixing efficiency does not always increase with higher oscillating frequency of stirrer. Consequently, we found the functional relation between the optimal frequency of a stirrer and the Reynolds number.

• 청정기술
• /
• 제18권4호
• /
• pp.404-409
• /
• 2012

본 연구는 교반강도 및 응집제 주입량의 변화에 따라 플럭의 성장특성이 인의 제거에 미치는 영향을 파악하고자 수행되었다. 본 연구에서는 Al/P 몰비를 1.0, 1.5와 2.0으로 급속혼화강도 G값을 100, 300과 500 $s^{-1}$로 변화시켜 수행하였다. 응집시 발생되는 응집지수(floc size index, FSI)와 크기가 다른 여과지를 이용하여 인의 제거율을 측정하여 성장 특성을 파악하였다. 연구결과 교반강도가 높을수록 용존인의 제거효율이 증가하였으며 Al/P 몰비가 낮을수록 교반강도의 영향이 컸다. T-P의 제거율은 Al/P 몰비 1.0 이하에서는 급속혼화 교반강도가 높을수록 높았으나 Al/P 몰비 1.0 이상에서는 G값 300 $s^{-1}$에서 가장 높은 제거 효율을 나타내었다. Al/P 비 1.0 이하에서는 G값 500 $s^{-1}$에서 가장 큰 FSI값을 나타내었으며, Al/P 몰비 1.0 이상에서는 G값 300 $s^{-1}$에서 가장 큰 FSI값을 나타내었다. 실제하수처리장 유출수를 대상으로 응집에 의한 인 제거에 Al/P 몰비와 급속혼화 강도의 영향은 인공조제수의 결과와 유사하였다.