• Journal of Korean Society of Water and Wastewater
• /
• v.19 no.4
• /
• pp.473-479
• /
• 2005

Applying enhanced coagulation is not uncommon not only to improve water quality but also to obtain economical advantages in water treatment. In this study, the economical evaluation was investigated with considering dosage of coagulant, produced sludges and usage of activated carbon with two different water sources. To simulate the granular activated carbon(GAC) adsorber mini-column test was adapted. Even if there were some variation according to the source waters, the life time of GAC was extended 60 to 110days with adding 2.5 to 3 times of coagulant in enhanced coagulation. With assumption of changing GAC adsorber at 50% of breakthrough the total treatment cost can be reduced to range from 25% to 44% with adapting the enhanced coagulation. The obtained value can not be generalized because the value can be varied by water quality and cost of the GAC or coagulant. However, the evaluation can be basis starting point to find optimum operation methods for the drinking water treatment which has plan to adapt GAC adsorber.

• Journal of Korean Society of Water and Wastewater
• /
• v.12 no.3
• /
• pp.30-40
• /
• 1998

Increasing water consumption produced sludge problems of the water treatment plants. The objective of this study is to investigate aluminium coagulants recovery n acidic and alkaline conditions. Water treatment plant sludge produced in Pusan Metropolitan City were tested for the aluminium extraction process. Experiment samples were obtained in summer from water treatment plants of Deoksan and Myongjang. Aluminium coagulants used in these plants during the test period were polyaluminium chloride(PAC), polyaluminium sulfate organic(PSO), polyaluminium sulfate silicate(PASS). Aluminium contents of water treatment sludge were in the range of 7.2~10.9% of the total solids. The recovery percentages for aluminium and iron by acidic extraction method was evaluated to 88% and 42% respectively. Extracted mass variation for other materials such as iron, manganese, total organic carbon was observed during the extraction operation. Alkaline extraction produced more than two times amount of total organic carbon than that in the acidic extraction process.

• The Journal of Korean Academy of Prosthodontics
• /
• v.17 no.1
• /
• pp.61-66
• /
• 1979

To investigate the variation of the mandibular rest position according to time, the mandibular rest position was induced by combination of relaxation and swallowing method. The displacement of the incisal point was recorded with the pinpointed miniature lamp luminograph in three dimensions immediately, 30 seconds, and 60 seconds after induction of the mandibular rest position. The Results obtained were as follows 1. Intermaxillary vertical distance measured immediately after induction of mandibur rest position ranged from 1.0mm to 3.9mm And it varied irregularly with time, ranging from 0.1mm to 1.1mm Anteroposterior variance with time ranged irregularly from 0.2mm to 0.8mm 2. The mandibular rest position observed in the frontal plane varied with time to right or left direction, ranging from 0.2mm to 0.5mm from the centric occlusion 3. the mandibular rest position wos not placed definite position but varied spatially in certain range with time.

• Proceedings of the KSME Conference
• /
• 2004.11a
• /
• pp.1640-1645
• /
• 2004

The pumping characteristics of a single-stage disk-type drag pump ( DTDP ) are calculated,for the variation of the vertical clearance between a rotor and stator and of the radial clearance between a rotor and casing wall, by the three-dimensional direct simulation Monte Carlo (DSMC)method. The gas flow mainly belongs to the molecular transition flow region. Spiral channels of a DTDP are cut on the both the upper and lower sides of a rotating disk, but the stationary disks are planar. As a consequence of results, the vertical and radial clearances have a significant effect on the pumping performance. Experiments are performed under the outlet pressure range of 0.4 $^{\sim}$ 533 Pa. When the numerical results are compared to the experimental data, the numerical results agree well qualitatively.

• Journal of the Korean Ceramic Society
• /
• v.30 no.5
• /
• pp.347-356
• /
• 1993

In joining alumina ceramics to metal by using Mo-Mn metallizing process the effects of metallizing thickness, temperature, and the composition of paste on the bond strength and the microstructure of joining interface were investigated. The bond strength variation in the range of metallizing temperature, 1350~155$0^{\circ}C$ was more than 150MPa above 145$0^{\circ}C$ and the optimum metallizing thickness was 30${\mu}{\textrm}{m}$. The optimum contents of Mn in Mo-Mn paste was 5% due to the bond strength decrease with the increase of addition. The effect of SiO2 addition in paste on bond strength was saturated around 200MPa. It was also observed that as the particle size of Mo decreased, the joinning with higher bond strength was shown in spite of low metallizing temperature.

• KSTLE International Journal
• /
• v.2 no.1
• /
• pp.22-28
• /
• 2001

A resin bonded copper-graphite brush was investigated to evaluate the characteristics electrical signal transmission through a sliding contact as a function of the relative amount of graphite and copper in the brush. Particular attention was given to the correlation between electrical signal fluctuation and tribological properties in an electrical sliding contact system. A ring-on-block type tribotester was used for this experiment and the ring was made from pure copper. Results showed that a copper-graphite brush at a particular composition range exhibited the most stable frictional behavior with a minimum voltage drop. The amount of voltage drop at the friction interface was affected by the surface roughness, transfer film formation at the friction interface, and the real area of contact. Microscopic observations and the surface analysis showed a good agreement with the results from this experiment. The results also indicated that the electrical signal flunctuation was directly associated with the oscillation of the coefficient of friction during sliding by nanoscale variation of contacts at the friction interface.

• Korean Journal of Plant Taxonomy
• /
• v.50 no.3
• /
• pp.361-367
• /
• 2020

We report meiotic chromosome numbers of three taxa in Carex sect. Mitratae in Korea: Carex breviculmis R. Br. (n = 32_II, 33_II, 34_II), C. polyschoena H. Lév. & Vaniot (n = 37_II, 38_II), and C. sabynensis Less. ex Kunth (n = 27_II). Section Mitratae is one of the most species-rich Asian groups in Carex, comprising approximately 45-80 taxa. Twenty-seven of these occur in Korea, and they are some of the most challenging taxa to identify due to their obscure and inconspicuous diagnostic characters. Including the counts reported here, half of the native Korean sect. Mitratae chromosome numbers have been documented. Their haploid chromosome numbers range from n = 10 to n = 40, and many exhibit variations in the numbers counted within a taxon. These variations, along with the overall significant variation in sect. Mitratae, suggest that dynamic chromosome activity may be related to the high species diversity of Carex.

• International Journal of Air-Conditioning and Refrigeration
• /
• v.9 no.1
• /
• pp.65-70
• /
• 2001

During the summer season, it is very hot and humid in Korea. So the humidity is an important factor regarding the environmental control function of building envelops. The purpose of this research is to measure and analyze the characteristics of such environmental factors as relative humidity, dry bulb temperature and air velocity varies both in the clay and cement envelop structures using granite dome models during the summer time. The interior relative humidity of the clay model is constant regardless of exterior humidity although a little range of variation is shown in comparison to the cement model.

• Journal of Industrial Technology
• /
• v.24 no.A
• /
• pp.139-155
• /
• 2004

A room and pillar mining method has been adopting at the Jeungsun limestone mine. To check stability of pillar with multiple and irregular openings, the size, shape and spacing of rib pillar were first designed using some empirical suggestions. The Finite Difference Method(FDM)was used to analyze the pillar stability. Twelve different cases with the variation of K(horizontal/vertical stress)values, different height and different spacing of pillar were used in this study. Finally Mohr-Coulomb criterion was adopted to calculate the safety factors. Horizontal and vertical displacement, maximum and minimum principal stresses, range of plastic zone and safety factors were calculated at each case. As a result of analysis, the size of one block is 160m long, 70m wide, 40m high with 20m wide rib pillar and 20m square column pillar. The overall recovery at this case can be estimated about 40%.

• Journal of Environmental Science International
• /
• v.10 no.1
• /
• pp.9-12
• /
• 2001

In this study, development of new sound absorbent which is safety, economical and efficient with using recycled materials is tried for substitution of commercial sound absorbent. The sound absorbents, used in this investigation, were made of used paper or filters of cigarette butts. With the variation of the material densities, sound absorptions of materials were measured. The impedance tube method is used for measuring sound absorption coefficient of the new sound absorbent materials. The measured frequency range was 250Hz to 4000Hz in 1/3 octave band. The sound absorption coefficient of the commercial materials and that of the materials synthesized in the our laboratory show almost same value.