• Journal of Advanced Marine Engineering and Technology
• /
• v.17 no.3
• /
• pp.12-23
• /
• 1993

Combustion phenomenon in diesel engine is mainly governed by characteristics of fuel injection and fuel spray system affected by its dimensions and operating condition. Fuel supply system is consisted of fuel injection pump, high pressure pipe and injection nozzle. In order to develope the more economical diesel fuel injection system, it is in need to carryout the fairly wide range experiments, which is quite impossible. Therefore, theoretical analysis for the numberous parameters is powerful method in this case. In the present study, equations of continuity of fuel oil in fuel injection system are solved to obtain the flow and pressure variation in diesel fuel system affected by injection pump speed, plunger diameter, pipe length and nozzle opening pressure.

• Proceedings of the IEEK Conference
• /
• 2008.06a
• /
• pp.593-594
• /
• 2008

In this article, process voltage temperature (PVT) compensated on-chip oscillator is implemented by using proportional to absolute temperature (PTAT) circuit and process compensator. Process compensator circuit based on current subtracter and PTAT circuit are proposed for compensation of oscillation frequency to cope with process variation and temperature variation. All circuit can operate in the range of $3.5{\sim}5\;V$ supply voltage. It can be applied to PVT insensitive low frequency clock reference generator.

• 한국연소학회:학술대회논문집
• /
• 2003.12a
• /
• pp.167-173
• /
• 2003

An experimental study on the behavior of droplets impinging on a solid flat surface was carried out in the present study. Breakup of a liquid droplet impinging on a solid surface has been investigated experimentally for various fuels with different properties. The fuel temperature and incident angle were chosen as major parameters. And fuel temperature and incident angle varied in the range from $-20^{\circ}C$ to $30^{\circ}C$ and from $30^{\circ}$ to $60^{\circ}$, respectively, were investigated. It was found that the variation of fuel temperature influences upon droplet mean diameter which were bounced out from the solid surface. As the increases of incident angle, the break-out mass flow rate increases. This causes the decrease of liquid film flow rate. The larger incident angle gives less liquid film flow rate.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2003.11a
• /
• pp.371-376
• /
• 2003

The objective of this paper is to compare the site-to-site variability of ISO 10844 pass-by-noise test sites. In order to investigate the site-to-site variance of test surfaces, European commercial tires are tested at seven different test sites. Three Korea test sites and four Europe test sites are selected.. The pass by noise test is executed according to a 2001/43/EC regulation. A]though the ISO surface has a very specific track composition, it does not reduce the variation of pass-by-noise measurements over the surface of test sites. This paper shows that the test results of pass-by-noise level are different depending on the test sites. The correlation obtained in this work is able to predict the pass by noise level for certain test site using the data measured from another test site. 17he prediction value is range with an error within 1dB(A).

• The Journal of the Acoustical Society of Korea
• /
• v.21 no.5
• /
• pp.485-493
• /
• 2002

Broadband interference patterns are studied using ship as an acoustic source in shallow waters with varying bathymetry. Waveguide invariant index (β) indicating the pattern of constructive (or destructive) interference in range-frequency domain is derived in a waveguide with constant bottom slope based on adiabatic mode theory. Using this invariant, changes of the interference patterns resulting from the variation of bottom bathymetry are analyzed. Results of the analytic interpretation is compared with those from sea experiments and numerical simulations.

• Journal of the Korea Safety Management & Science
• /
• v.2 no.1
• /
• pp.89-97
• /
• 2000

This paper shows the study for development inprocess measuring magnetic sensor for tolerance control, First, we fabricated and annealed sample amorphous ribbons which were made of ($CO_{0.94}$$Fe_{0.06}$)$_{79}$$Si_{2}$$b_{19}$ having near zero magnetostrictive. It had 12［$\mu\textrm{m}$］ of thickness, 10［mm］ of length, and 2.5［mm］ of width. Then, we measured the magnetic characteristics such as frequency dependency over impedance variation rate and position change over impedance variation. As the results of the evaluation, we found that the sample ribbons had excellent sensor characteristics. Then, we made sensors by using the sample ribbons, As the results of the measurements, it proved that the ribbon could be used as excellent magnetic sensor for which it was possible to control inprocess measurement within the tolerance range(~$\mu\textrm{m}$ ).

• Journal of Information Display
• /
• v.7 no.3
• /
• pp.9-12
• /
• 2006

A new voltage-scaled compensation pixel which employs 3 p-type poly-Si TFTs and 2 capacitors without additional control line has been proposed and verified. The proposed pixel does not employ the $V_{TH}$ memorizing and cancellation, but scales down the inevitable $V_{TH}$ variation of poly-Si TFT. Also the troublesome narrow input range of $V_{DATA}$ is increased and the $V_{DD}$ supply voltage drop is suppressed. In our experimental results, the OLED current error is successfully compensated by easily controlling the proposed voltage scaling effects.

• Journal of the Korean Geophysical Society
• /
• v.9 no.3
• /
• pp.241-248
• /
• 2006

In this study, we applied the teleseismic receiver function technique to determine the crustal thicknesses and ratios for 31 broadband stations of the Korean Peninsula and map out the lateral variation of Moho depth in the Peninsula. The estimated depths to Moho range from 26 to 35 km except for an island station ULL (17 km). The Moho is turned out to be deeper in the south-western part of the Peninsula and western Gyeongsang basin, and shallower in the off-shore region close to East Sea (Sea of Japan). The ratio varies from 1.69 to 1.89 with the average of 1.77, which is close to global average (1.78) in the crust.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2023.05a
• /
• pp.137-138
• /
• 2023

This study proposed the optimal mixing time for pre-mixed cement and post mixed cement using the statistical analysis method of box plots. Pre-mixed cement can prevent material seegregation, strength loss, and quality variation if mixed for at least 60 seconds, and the data median is shown to be within the box range. Post-mixed cement should be mixed for at least 180 seconds to prevent material segregation, strength loss, and quality variation, and compressive strength tends to increase with longer vibrating times. Therefore, it is suggested that using pre-mixed cement can shorten the vibrating time and increase the productivity of the concrete.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.43 no.10 s.352
• /
• pp.61-67
• /
• 2006

We developed a constant current source which is insensitive to threshold voltage variation caused by irregular grain boundary distribution in polycrystalline silicon. The proposed current source has superior saturation characteristics over wide range of input voltages as well as small current error compared to the previously reported Vth compensated sources. We measured the circuit performance and error in current due to parameter variation by using HSPICE.