• 오토저널
• /
• 제9권5호
• /
• pp.49-56
• /
• 1987

This paper is a study on the effect of the cutting speed on the tool wear in turning of the glass fiber reinforced plastics. The wear behavior of cutting tool is studied by means of turning, changing the cutting speed and feed in the wide range. Moreover, the theoretical model applicable to the cutting speed of wide range is analysed. The main results obtained are as follows: The relation between the tool wear and the cutting speed is divided into three range in case of the constant cutting distance. 1) At the low cutting speed, the tool wear is independent of the cutting speed, but dependent mainly on the contact length between tool and glass fiber(lst range). 2) At the high cutting speed, the tool wear is independent of the contact length, and dependent on the cutting speed only(2nd range). The tool wear increases in proportion to the cutting speed. 3) At the higher cutting speed than the speed in the 2nd range, the tool wear is independent both of the cutting speed and the contact length(3rd range). 4) In the 3rd range, tool flank wear is constant and is observed that only the wear of cutting edge increases.

• 오토저널
• /
• 제14권6호
• /
• pp.113-126
• /
• 1992

Recently the multi-kind, small-amount manufacturing system has been replacing the mass manufacturing system, and domestic machining inustry also is eager to absorb the new technology because of its high productivity and cost reduction. The optimization of the cutting condition has been a vital problem in the machining industry, which would help increase the productivity and raise the international competitiveness. It is intended in this study to investigate the machining costs per unit time which is essential to the analysis of the optimal cutting condition, to computer the cutting speed that lead to the minimum machining costs and the maximum production to suggest the cutting speed range that enables efficient speed cutting, and to review the machining economy in relation to cutting depth and feed. Also considered are the optimal cutting speed and prodution rated in rrelation with feed. It is found that the minimum-cost cutting speed increases and the efficient cutting speed range is reduced as machining cost per unit time increases since the cutting speed for maximum production remains almost constant. The machining cost is also lowered and the production rate increases as the feed increases, and the feed should be selected to satisfy the required surface roughness. The machining cost and production rate are hardly affected by the cutting depth if the cutting speed stays below 100m/min, however, they are subject to change at larger cutting depth and the high-efficient speed range also is restricted. It can be established an adaptive optimal cutting conditions can be established in workshop by the auto-selection progam for optimal operation. It is expected that this method for choosing the optimal cutting conditions might contribute to the improvement of the productivity and reduced the cost. It is highly recommended to prepare the optimal cutting conditionthus obtained for future use in the programing of G-function of CNC machines. If proper programs that automatically select the optimal cutting conditions should be developed, it would be helpful to the works being done in the machine shops and would result in noticeable production raise and cost reduction.

• 대한기계학회논문집
• /
• 제12권5호
• /
• pp.1055-1062
• /
• 1988

본 연구에서는 역학모델을 이용해 공구마멸 특성을 절삭속뿐만 아니라 공구와 유리섬유의 접촉길이에 대해서도 논하고, 이 결과와 실험결과를 대비 검토하였다. 또 몇 가지 공구재종으로 절삭성능을 측정하였다.

• 한국정밀공학회지
• /
• 제25권2호
• /
• pp.28-34
• /
• 2008

Recently, with the development of high speed machining technology for difficult-cutting materials, to improve the cutting performance of cutting tool, fine surface finish of complex shape tools using magnetic polishing technology is in high demand. This study is, therefore, discussed and compared the cutting characteristics of polished tools by the adopted various magnetic polishing moving types a point of view the cutting forces and the tool life. Moreover, the practicality of magnetic polished tools in the wide range cutting conditions is investigated. From obtained results, It is confirmed that the CW(clockwise) revolution and oscillation type as the polishing moving type is proper and magnetic polished tool shows the excellence in high cutting speed range.

• 한국정밀공학회지
• /
• 제17권5호
• /
• pp.186-194
• /
• 2000

The purpose of this study is to investigate the difference in cutting characteristics of cermet, carbide and coated carbide tools in the similar application range via turning test of various conditions. The cermet and carbide tools in the range of ISO P10 grade were developed using optimum compositions with a view to obtaining a high toughness and hardness by PM process. First mechanical properties were characterized on these tools. Experimental results of wear behaviour and resistance to fracturing were presented and discussed in the turning of gray cast iron and alloy steels by cermet, carbide and coated carbide tools. The coated carbide tool shows similar cutting performance compared to the cermet, while the cermet has better combination of wear resistance and toughness of high speed (V=500m/min) cutting in comparison with carbide and coated carbide tools, and also shows a potentiality for cast iron cutting. Fe adhesive behaviour on the tools and surface roughness of workpieces were explained by chemical affinity between tools and workpieces.

• 한국생산제조학회지
• /
• 제7권6호
• /
• pp.90-96
• /
• 1998

The ductile cast iron is austempered at 300, 350 and 40$0^{\circ}C$ temperature in order to investigate the basic factors for monitoring drill wear in automatic production process, and cutting force and AE RMS signals are measured with changing cutting condition for ADI(Austempered Ductile Cast Iron) with different mechanical properties. The signals of cutting force were influenced by cutting speed and feedrate greatly. On the other hand AE RMS signals are influenced by cutting speed where as it is not related with feedrate. As the depth of drilling increases, cutting force shows a slow increase and the value of AE RMS increases until the range of h/d=4. But over the range it increases greatly due to an amount of chip discharge and friction with inner wall of drilling hole, etc. As the drill diameter increases at a constant depth of drilling. Cutting force increases linearly, but the level of AE RMS does not increases linearly due to circumferential velocity and great influence of h/d.

• Journal of Welding and Joining
• /
• 제13권4호
• /
• pp.113-121
• /
• 1995

This study deals with the quality and the optimum range of laser cutting process. Cold rolled steel sheets for automobile application were cut by a high power CO$_{2}$ laser system with beam quality of TEM$_{\infty}$ mode. Both process parameters such as travel speed and assist gas pressure, and quality factors were considered to optimize the laser cutting. It was revealed that the thinner the sheet thickness, the less effect of oxidation energy for contributing the cutting process. High speed photographs demonstrated that molten spot on the cut surface moved in a random and vigorous manner according to its viscosity and the flowing direction of assist gas, which resulted in so called striation. Laser cutting produced a very smooth surface of average roughness(Ra) about less than 1.5.mu.m at the optimum range. It was also shown that the characteristics of dross formation was influenced by the flowing durection of assist gas and the fluidity of molten metal drop..

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1990년도 한국자동제어학술회의논문집(국내학술편); KOEX, Seoul; 26-27 Oct. 1990
• /
• pp.170-174
• /
• 1990

The information with regard to the working range of lathe, cutting tool, cutting condition is managed as Database system for turning operation as one part of CAM system. Data with regard to the working range of lathe, cutting tool, cutting condition are stored by the DBMS(Data Base Management System) and can be added, modified, deleted and retrieved for realtime usages. Data stored in Database system are searched to select the most proper cutting tool and cutting condition with the input data fed from the design stage. Codes in regards to tool shape are displayed on graphic mode for easy selection for user and thus presents a good decision support for tool selection. The system developed in this work is operated by the pull down menu on the IBM PC/AT personal computer, or compatible series.

• 한국정밀공학회지
• /
• 제12권12호
• /
• pp.72-80
• /
• 1995

Ultraprecision machining technology has been playing a rapidly increasing and important role in manufacturing. However, the physics of the micromachining process at very small depth of cut, which is typically 1 .mu. m or less is not well understool. Shear along the shear plane and friction at the rake face dominate in conventional machining range. But sliding along the flank face of the tool due to the elastic recovery of the workpiece material and the effects of plowing due to the large effective negative rake angle resultant from the tool edge radius may become important in micromachining range. This paper suggests an orthogonal cutting model considering the cutting edge radius and then quantifies the effect of plowing due to the large effective negative rake angle.

• 한국생산제조학회지
• /
• 제21권3호
• /
• pp.387-393
• /
• 2012

It is very difficult to determine suitable cutting conditions in order to obtain accurate cutting profiles because machining errors caused by tool deflection depend upon cutting conditions. In this study the relationship between real cutting profiles (inclined shapes and machining errors) and cutting conditions was modeled in order to fabricate draft angle on micro molds. CCD (Central Composite Design) of DOE (Design Of Experiment) and RSM (Response Surface Method) were applied in order to model the relationship between cutting conditions and machining errors. In order to use CCD the range of radial depth of cut was chosen by $10-90{\mu}m$ and the range of feedrate was chosen by 200-300mm/min, and 9 points of cutting conditions were chosen inside determined ranges. Then, actual cutting processes were carried out as respect to 9 points of cutting conditions, draft angles and real cutting profiles were measured on cutting profiles, each response surface function was determined by conducting response surface analysis and the functions were represented by 3-dimensional graphs, contour lines and $101{\times}101$ matrices. Consequently it is possible to determine suitable cutting conditions in order to obtain arbitrary given draft angles and cutting profiles by using modeling. To validate proposed approach in this study suitable cutting conditions were determined by modeling in order to obtain arbitrary given draft angle and cutting profile, and actual cutting processes were carried out. About 95% of good agreement between predicted and measured values was obtained.