• 대한기계학회논문집A
• /
• 제33권10호
• /
• pp.1099-1107
• /
• 2009

Numerical simulation and experimental study to evaluate the critical speed of the railway bogie according to the tread inclination of wheel profile were conducted using 1/5 scale model. It has been shown that the results of the critical speed analysis for the scale bogie model is very close to the test results using scale bogie model and the critical speed is decreased in proportion to the increase of equivalent conicity of wheel profile. Results of this study show that the scale model could be applied to research area relating to vehicle stability as an alternative to overcome the experimental problems caused by full scale test on the roller rig.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2011년도 정기총회 및 추계학술대회 논문집
• /
• pp.986-993
• /
• 2011

The role of brake is safely to transport passenger & cargo and stop vehicles at emergency in railway vehicle. Brake system reduces the speed by control command of electricity or air. mechanical methods to perform brake are disk brake & tread brake. This study targeted development of highly efficient sintered alloy brake shoe in railway vehicle whose high frictional coefficient, wear resistance, compatibility of the existing tread brake shoe & minimization of wheel's thermal damage and performed development of friction material's formulation, analysis of pressure distribution in wheel tread & brake shoe, optimum form design through analysis of heat flow.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2008년도 춘계학술대회 논문집
• /
• pp.981-982
• /
• 2008

• 한국철도학회논문집
• /
• 제5권3호
• /
• pp.167-173
• /
• 2002

The influence of thermal stress at tread breaking in Korean High Speed Train wheel was investigated using the coupled thermal-mechanical analysis technique. The mechanical load or wheel-rail contract load and braking load were considered during FEM analysis. During the stop braking, the effect of mechanical stress on the combined stress is relatively larger than that of thermal stress in the rim of wheel. However, the effect of thermal stress is relatively larger than that of mechanical stress in the plate of wheel. When 300% of the block force was applied, the maximum von Mises stress of 61.0 MPa was found at the outside plate around 400 mm far away from the wheel center.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2009년도 춘계학술대회 논문집
• /
• pp.1598-1603
• /
• 2009

Recently, several wheel for freight car in running had experienced the wheel failure due to fatigue crack, overheat braking and other factors. Severe heating of the wheel during tread braking was believed to be a contributing factor of derailment. It is necessary to evaluate the residual stress in wheel tread. In the present paper, the residual stress of wheel using x-ray diffraction system is investigated. the result shows that the residual stress of wheel is depend on the running distance and wear rate of wheel.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2007년도 추계학술대회 논문집
• /
• pp.1940-1945
• /
• 2007

The wheelsets are one of most important component: damages in wheel tread and press fitted axle are a significant cost for railway industry. Since failure in railway wheelset can cause a disaster, regular inspection of defects in wheels and axles are mandatory. Ultrasonic testing, acoustic emission and eddy current testing method and so on regularly check railway wheelset in service. However, it is difficult to use this method because of its high viscosity and because its sensitivity is affected by temperature. Also, due to noise echoes it is difficult to detect defects initiation clearly with ultrasonic testing. It is necessary to develop a non-destructive technique that is superior to conventional NDT techniques in order to ensure the safety of railway wheelset. In the present paper, the new NDT technique is applied to the detection of surface defects for railway wheelset. To detect the defects for railway wheelset, the sensor for defect detection is optimized and the tests are carried out with respect to surface and internal defects each other. The results show that the surface crack depth of 1.5 mm in press fitted axle and internal crack in wheel could be detected by using the new method. The ICFPD method is useful to detect the defect that initiated in the tread of railway wheelset.

• 한국정밀공학회지
• /
• 제27권8호
• /
• pp.28-34
• /
• 2010

Railway wheel and axle is the most critical components in railway system. A wheel and axle failure can cause a derailment with its attendant loss of life and property. The service conditions of railway vehicles have become severe in recent years due to a general increase in operating speeds. Therefore, more precise evaluate of wheelset strength and safety has been desired. Fracture mechanics characteristics such as dynamic fracture toughness, fatigue threshold and charpy impact energy with respect to the tread, plate, disc hole of wheel and the surface of press fitted axle are evaluated. This paper describes the difference of fracture toughness, fatigue crack growth and fatigue threshold at the locations of wheel and axle. The results show that the dynamic fracture toughness, $K_{ID}$, is obviously lower than static fracture toughness, $K_{IC}$ and the fracture mechanics characteristics are difference to the location of wheel tread and hole.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2005년도 추계학술대회 논문집
• /
• pp.88-93
• /
• 2005

Frictional heat generates when the brake shoes are in contact with wheel tread under high pressure for EMU's speed control, stopping, and deceleration. Such a frictional heat has a significant effect on the wheel tread. In order to analyze the characteristics of frictional heat and measure the amount of the generated heat, tests by using a brake dynamometer and for running vehicles are carried out. In addition, finite element analysis is performed to simulate the temperature distribution and thermal analysis of the brake shoes. Through the tests and the simulations, it is found that the problems by temperature increase at tread braking are verified.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2010년도 춘계학술대회 논문집
• /
• pp.1465-1466
• /
• 2010

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2004년도 춘계학술대회 논문집
• /
• pp.789-797
• /
• 2004

The wear and defects on the wheel tread are caused by the interface between wheel and rail, the suspension system on bogie, the track condition and etc, which are interacted with complex mechanism. Because of the difficulty of analysis of wheel and rail interaction, the measuring data are necessary for improvement of wheel design and maintenance of train. On this case study, the pattern of wheel wears and defects are presented and lifetime of wheel and the reprofiling period are estimated on a basis of the measured results.