• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2009년도 추계학술대회 논문집
• /
• pp.772-778
• /
• 2009

By rising the interests of the railroad, It has been required the research about railroad structure. And since 2000, the study about railway bridges caused by steel box railway bridges has been only 0.2%. So I was hard to find out about steel box railway bridges. In this study, I evaluate and analyze 4 types(KTX, Saemaeul, Mugunghwa, Freight) of dynamic caused by train loading, natural frequency and damping ratio, verticality deflection and verticality acceleration, end slope deflection, impact factor for dynamic characteristics analysis. natural frequency was measured 2.45Hz~3.34Hz and damping ratio revealed for 1.26~2.84%. Maximum verticality deflection(4.86mm) was sufficiently satisfied the design criteria(30.1mm), but in the case of verticality acceleration's respond, design criteria BRDM(Bridge Design Manual) & CTRL presentation derive rail limit value 0.35g be more than value 6 time recorded, maximum was measured 0.49g in 3 kinds of train(KTX, Saemaeul, Mugunghwa), except for Freight. Survey impact factor of Experiment bridge was 0.20 which is measured when the KTX(15:04) was driving. impact factor is enough contended with design criteria 0.29 which is presented in domestic railway design criteria and thoroughly guarantee the dynamic stability.

• 한국공간구조학회논문집
• /
• 제20권2호
• /
• pp.87-94
• /
• 2020

The present study is aimed to calculate the optimal damping according to the seismic load on the structure with a non-seismic design to perform structure analysis considering the deformation of structural joint connection and panel zone; to develop design program equipped with structural stability of the steel frame structures reinforced with the panel zone and viscous dampers, using the results of the analysis, in order to systematically integrate the seismic reinforcement of the non-seismic structures and the analysis and design of steel frame structures. The study results are as follows: When considering the deformation of the panel zone, the deformation has been reduced up to thickness of the panel double plate below twice the flange thickness, which indicates the effect of the double plate thickness on the panel zone, but the deformation showed uniform convergence when the ration is more than twice. The SMRPF system that was applied to this study determines the damping force and displacement by considering the panel zone to the joint connection and calculating the shear each floor for the seismic load at the same time. The result indicates that the competence of the damper is predictable that can secure seismic performance for the structures with non-seismic design without changing the cross-section of the members.

• 한국소음진동공학회논문집
• /
• 제19권12호
• /
• pp.1306-1314
• /
• 2009

By rising the interests of the railroad, It has been required the research about railroad structure. And since 2000, the study about railway bridges caused by steel box railway bridges has been only 0.2 %. So I was hard to find out about steel box railway bridges. In this study, I evaluate and analyze 4 types(KTX, Saemaeul, Mugunghwa, Freight) of dynamic caused by train loading, natural frequency and damping ratio, verticality deflection and verticality acceleration, end slope deflection, impact factor for dynamic characteristics analysis. natural frequency was measured 2.45 Hz~3.34 Hz and damping ratio revealed for 1.26~2.84 %. Maximum verticality deflection(4.86 mm) was sufficiently satisfied the design criteria(30.1 mm), but in the case of verticality acceleration's respond, design criteria BRDM(bridge design manual) & CTRL presentation derive rail limit value 0.35 g be more than value 6 time recorded, maximum was measured 0.49 g in 3 kinds of train(KTX, Saemaeul, Mugunghwa), except for Freight. Survey impact factor of Experiment bridge was 0.20 which is measured when the KTX(15:04) was driving. impact factor is enough contended with design criteria 0.29 which is presented in domestic railway design criteria and thoroughly guarantee the dynamic stability.

• 지질공학
• /
• 제30권1호
• /
• pp.43-57
• /
• 2020

본 연구는 기존의 강지보재보다 우수한 고강도 격자지보재를 개발하여 그 성능을 평가하기 위함이다. 이를 위해 수치해석을 이용한 지보재의 구조적 특성을 분석하였고, 시작품에 대한 최대 굽힘하중시험과 용접이음부 인장강도시험을 실시하여 그 성능을 평가하였다. 구조해석 결과에 따른 최적의 상하부부재와 플레이트의 규격은 50 mm × 31.8 mm × 25.4 mm로 시공성과 경제적이 우수한 것으로 나타났다. 굽힘 하중시험으로부터 확정된 규격 55 mm × 30 mm × 20 mm와 85 mm × 30 mm × 20 mm의 고강도 격자지보재는 기준값과 H형강 100과 125의 목표값 모두 만족하는 것으로 나타났다. 이론 처짐량과 실제 처짐량의 비를 검토한 결과, 이 연구에서 개발된 고강도 격자지보재는 독일연방 철도국에서 제시하고 있는 격자지보재 처짐량의 평가기준 5 이하로 나타났다. 마지막으로 용접이음부에 대한 인장시험 결과는 고강도 격자지보재의 주봉-보조봉-플레이트가 접하는 용접이음부 인장강도가 목표값 이상으로 나타나 용접이음부에 대한 안정성은 충분한 것으로 나타났다.

• Smart Structures and Systems
• /
• 제19권2호
• /
• pp.225-236
• /
• 2017

Railroad bridges in North America are an integral but aging part of the railroad network and are typically only monitored using visual inspections. When quantitative information is required for assessment, railroads often monitor bridges using accelerometers. However without a sensor to directly measure displacements, it is difficult to interpret these results as they relate to bridge performance. Digital Image Correlation (DIC) is a non-contact sensor technology capable of directly measuring the displacement of any visible bridge component. In this research, a railroad bridge was monitored under load using DIC and accelerometers. DIC measurements are directly compared to serviceability limits and it is observed that the bridge is compliant. The accelerometer data is also used to calculate displacements which are compared to the DIC measurements to assess the accuracy of the accelerometer measurements. These measurements compared well for zero-mean lateral data, providing measurement redundancy and validation. The lateral displacements from both the accelerometers and DIC at the supports were then used to determine the source of lateral displacements within the support system.

• Steel and Composite Structures
• /
• 제12권5호
• /
• pp.427-444
• /
• 2012

This paper presented a new aerial platform-AERORail for rail transport and its structure evolution based on the elastic stiffness of cable; through the analysis on the cable properties when the cable supported a small service load with high-tensile force, summarized the theoretical basis of the AERORail structure and the corresponding simplified analysis model. There were 60 groups of experiments for a single naked cable model under different tensile forces and different services loads, and 48 groups of experiments for the cable with rail combined structure model. The experimental results of deflection characteristics were compared with the theoretical values for these two types of structures under the same conditions. It proved that the results almost met the classical cable theory. The reason is that a small deflection was required when this structure was applied. After the tension increments tests with moving load, it is verified that the relationships between the structure stiffness and tension force and service load are simple. Before further research and applications are made, these results are necessary for the determination of the reasonable and economic tensile force, allowable service load for the special span length for this new platform.

• 한국정밀공학회지
• /
• 제30권7호
• /
• pp.673-678
• /
• 2013

Driving gear units can be affected by various problems, including those associated with external or internal defects in the bearing, problems with the lubricant oil, high-loading of the railway, and frequent impacts generated by rail joints. Temperature monitoring is a basic method in diagnosing abnormal conditions in the reduction gear and other components. This paper describes a new wireless monitoring system for the temperature diagnosis of abnormal conditions of the reduction gear. Integrated circuit (IC)-type temperature sensors were installed in the reduction gear box of a high-speed railway car. The temperature data from the reduction gear were acquired and analyzed in situ during high-speed rail operation. Analysis of these data was used to alert the driver and/or maintenance personnel when problems occurred.

• 한국공작기계학회논문집
• /
• 제17권3호
• /
• pp.78-85
• /
• 2008

Roll forming process is one of the most widely used processes in the world for forming metals. It can manufacture goods of the uniform cross section throughout the continuous processing. However, process analysis is very difficult because of the inherent complexity. Therefore, time is consuming and much money are needed for manufacturing goods. In order to overcome this difficulty, a new computational method based on the rigid-plastic finite element method is developed for the analysis of roll forming process. In this paper, the design of roll forming process and the simulation are performed to manufacture the upper member at under rail composed of three members. The cold rolled carbon steel sheet(SCP-1) is used in this simulation, and a flow stress equation is set up by conducting the tensile test. The upper member is designed using two types of design for a excellent design. Each types are simulated and compared with the strain distribution using SHAPE-RF software. In addition, the numerical magnitude of bow and camber which are the buckling phenomenon is estimated.

• 한국철도학회논문집
• /
• 제15권3호
• /
• pp.266-271
• /
• 2012

본 연구는 빠르게 대중화 되어가는 철도의 주행안전성과 승차감 개선을 목적으로 수행하였다. 가스압접을 실시하는 장대레일의 강도 안전성을 확보하기 위하여 인장시험과 회전굽힘시험을 실시했다. 실험을 통하여 가스 압접부의 인장강도를 결정하는 요소는 가해진 압력보다 업셋길이의 변화에 기인하며, 업셋길이가 늘어남에 따라서 취성파괴에서 연성파괴가 발생하는 것을 관찰했다. 파단면의 조직검사를 통해 그 면에 존재하는 취성파면의 유무에 따라서 강도 안전성을 용이하게 평가할 수 있었다. 회전굽힘시험 결과 업셋길이 25mm에서 373MPa의 우수한 피로한도가 나타났으며, 무한수명을 얻을 수 있었다.

• Steel and Composite Structures
• /
• 제31권6호
• /
• pp.591-600
• /
• 2019

Based on the energy-variational principle, a coupling vibration analysis model of high-speed railway simply supported beam bridge-track structure system (HSRBTS) was established by considering the effect of shear deformation. The vibration differential equation and natural boundary conditions of HSRBTS were derived by considering the interlayer slip effect. Then, an analytic calculation method for the natural vibration frequency of this system was obtained. By taking two simply supported beam bridges of high-speed railway of 24 m and 32 m in span as examples, ANSYS and MIDAS finite-element numerical calculation methods were compared with the analytic method established in this paper. The calculation results show that two of them agree well with each other, validating the analytic method reported in this paper. The analytic method established in this study was used to evaluate the natural vibration characteristics of HSRBTS under different interlayer stiffness and length of rails at different subgrade sections. The results show that the vertical interlayer compressive stiffness had a great influence on the high-order natural vibration frequency of HSRBTS, and the effect of longitudinal interlayer slip stiffness on the natural vibration frequency of HSRBTS could be ignored. Under different vertical interlayer stiffness conditions, the subgrade section of HSRBTS has a critical rail length, and the critical length of rail at subgrade section decreases with the increase in vertical interlayer compressive stiffness.