• 한국자동차공학회논문집
• /
• 제19권3호
• /
• pp.99-105
• /
• 2011

This paper described the effect of the multiple injections on the emission characteristics and combustion stability in a common rail diesel engine. In order to investigate the influence of multiple injections in a passenger car diesel engine, the injection strategy was varied with pilot injection, post injection and one main injection at various conditions. Based on the experimental results, the combustion and emissions characteristics were analyzed for the various injection strategies such as main, pilot-main, double-pilot-main, double- pilot-main-post injection strategy. It is revealed that the $NO_X$, HC and CO emissions are reduced by double pilot and post injection at medium load, however, soot emission is increased. Also, in the case of multiple injection, the combustion pressure is increased smoothly near the TDC and the coefficient of variation and fuel consumptions are decreased.

• 한국자동차공학회논문집
• /
• 제19권3호
• /
• pp.38-43
• /
• 2011

A CNG/diesel dual-fuel engine uses CNG as the main fuel and injects a small amount of diesel as an ignition priming. This study proposed the modification of the existing diesel engine into a dual-fuel engine that injects diesel with a high pressure by common rail direct injection (CRDI) and by injecting CNG at the intake port for premixing. And experiment was progressed for understanding about effect of CNG mixing ratio. The CNG/diesel dual-fuel engine showed equally satisfactory coordinate torque and power regardless of CNG mixing ratio. The PM emission was low at any CNG mixing ratio because of very small diesel pilot injection. In case of NOx and HC, high CNG mixing ratio showed low NOx and HC emissions at low speed. At medium & high speed, low CNG mixing ratio showed low NOx and HC emissions. Therefore, it would be optimized by controlling CNG mixing ratio.

• 한국자동차공학회논문집
• /
• 제21권5호
• /
• pp.169-175
• /
• 2013

CRDi technology of diesel engine was developed from in the early 2000s due to a need to increase fuel efficiency and environment care. Especially, high-pressure fuel injection system in CRDi system which has a fuel injection unit including an injector, a fuel pump and common-rail, etc. becomes possible to make the exhaust gas clean as well as power improvement. In this study, comparison of dynamic characteristics of servo-hydraulic piezo-driven injector with 3-way and bypass-circuit type was analyzed by using the AMESim code. As results of this study, it found the bypass-circuit inside servo-hydraulic piezo injector can cause a faster injection response than that of the 3-way type. Also it was shown that bypass-circuit type had better control capability due to hydraulic bypass system.

• 한국산업융합학회 논문집
• /
• 제18권4호
• /
• pp.207-215
• /
• 2015

Since the oil shock of 1970's there was a strong upward tendency for the use of the high viscosity and poorer quality fuels. Therefore the misfiring engine occurs due to the decrease of quantity injected for lean burn and emission control in CI diesel engine. In this study, it is designed and used the test bed which is installed with turbocharger and intercooler. In addition to equipped using CRDI by controlling injection timing with mapping modulator, it has been tested and analyzed the engine performance, combustion characteristics, and emission as operating parameters.

• 한국분무공학회지
• /
• 제20권4호
• /
• pp.217-222
• /
• 2015

In this study, Injection rate tests of a Diesel common-rail injector have been performed with injection volume measurement type injection rate test system EMI21 for construction of injector model can be used in an engine calibration mean valued model. The measuring principle of the test system is based on measurement of dispalcement of a movable measurement piston by the volume of fluid released by the injector. From these injection rate test results, the characteristics on shape of instantaneous injection rate and injection fuel amount have been investigated and injection fuel amount calculation equation based on test results has been newly constructed. This equation is very simple and calculation error is less than 5% with test results for wide range injection pressure (200~1800 bar) and injection duration ($200{\sim}1800{\mu}s$) conditions. So, it is anticipated that newly constructed simple injection fuel amount model in this study can be efficiently used on engine calibration and control model.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2008년도 추계 학술발표회
• /
• pp.1167-1174
• /
• 2008

Vertical drain method, which is one of the soft ground improvement methods, shorten s drain path to accelerate consolidation process and is applied in many sites. At a recent, composite discharge capacity experiment that analyze discharge amount by consolidation behavior with overburden pressure of soft ground in laboratory, simulates similarly with actuality. Geotechnical engineering problems such a s soft ground improvement are solved by numerical analysis by development of computer and numerical analysis techniques. Numerical analysis does that result is contrary by user's inexperience for choice of constitution model and application of analysis method. Therefore, this thesis experiments on composite discharge capacity test and study discharge capacity of drain and consolidation behavior of soft ground installed prefabricated vertical drain boards. Also, This thesis studied reasonable input parameters and constitution model by compare results of composite discharge capacity test and numerical analysis using PLAXIS that is 2D finial element numerical analysis program.

• 대한기계학회논문집B
• /
• 제32권12호
• /
• pp.907-914
• /
• 2008

This study is mainly focused on the assessment of return, semi return, and returnless fuel supply system for an LPi engine. In order to compare the return type with returnless one with various LPG blends, combustion analysis and cyclic THC emission characteristic were tested at the part load operating condition of the LPi engine. Considering heat balance of each fuel supply systems, pressure and temperature increment of return type showed lower at the fuel rail during idle warm up operation. However, those of returnless type at LPG tank maintained stable and slow increment because the heat transfer from the LPi engine was minimized. Finally, hot restartability of each fuel supply systems were evaluated with the various LPG blends and fuel temperatures. As a result, semi return type has equivalent performance to return type considering combustion and emission characteristic, hot restartability performance for LPi engine.

• 한국분무공학회지
• /
• 제16권3호
• /
• pp.134-139
• /
• 2011

Recent research has focused on engine combustion technology as well as application of after-treatment in order to comply with emission regulation. However, it is much more efficient way to control emissions from engine itself and furthermore research on engine control will provide the direction of after-treatment technology in future. Furthermore, emission standard regulation for passenger diesel vehicles has been stringent compared to others and nano-particles will be included in EURO6 regulation in Europe and similar emission standard will be introduced in Korea. A 3.0 liter high speed diesel engine equipped with by CRDI system of 160MPa injection pressure, and an intake/exhaust system of V type 6 cylinder turbo-intercooler was applied. The injection duration and injection quantity, pilot injection types which are related to CRDI and air/fuel ratio control applied by EVGT were changed simultaneously. Standard experiment procedure constituted dilution apparatus and CPC system to collect nano-particles and these test results were compared with regulated materials of CO, HC, NOx and investigated their relations and characteristics of nano-particles.

• 센서학회지
• /
• 제27권6호
• /
• pp.380-385
• /
• 2018

Recently, interest in baseball has been increasing as the level of international baseball games, the popularity of domestic leagues, and the number of players entering the MLB has increased. In this paper, we propose a pitching system that can be applied to both professional and amateur baseball. The pitching system consists of a control module using MSB764T PLC, a pitching mechanism including AC motors and a ball feed rail, an HMI using the CHA-070WR model, inverter, etc. To pitch the breaking balls, the two AC motors each use an inverter to independently control the speed. The implemented pitching system was experimented on, investigating ball speed and ball movement according to RPM using the BUSHNELL Velocity Speed Gun. Experimental results on ball speed are similar to the theoretical data and the measured data. From the experimental data, it is confirmed that the damping coefficient value for the pitching ball is about 0.98. In the case of the breaking ball, the larger the difference between the speeds on the sides of the ball and the faster the ball speed, the larger the bending degree.

• 한국항해항만학회지
• /
• 제34권6호
• /
• pp.479-485
• /
• 2010

컨테이너의 신속한 이송 및 처리는 작업시간 단축에 의한 비용절감을 의미하므로 항만에서는 가능한 작업효율을 향상시키기 위해 다양한 노력이 추진되고 있다. 1990년대 중반부터 RMGC 및 RTGC 등의 크레인이 개발되어 컨테이너 이송 및 적재를 위한 필수장비로 널리 이용되고 있다. 특히 RTGC는 타이어 구동방식이므로 주행환경에 크게 제약을 받지 않는 장점도 있으나, 타이어 슬립, 타이어에 의한 샤시의 기울어짐 등 설정된 경로를 고정도로 주행해야 하는 목적달성에 장애가 되는 요인도 많아 레일 위를 주행하는 RMGC에 비해 자동화가 용이하지 않다. 이것은 무인 RTGC 시스템 구축을 어렵게 하는 가장 큰 요인이 되어 이와 관련한 기술개발 또한 미비한 수준에 이르고 있다. 따라서 본 논문에서 RTGC의 무인자동화에 있어서 가장 기초단계라고 볼 수 있는 수학적 모델링을 기반으로 한 고정도 주행제어기를 설계하고자 한다. 먼저 제어대상인 RTGC의 주행에 따른 운동특성을 분석하여 모델링을 수행한다. 기본적인 주행성능을 달성하기 위한 주행제어기를 설계하고 시뮬레이션을 통해 설계된 제어기의 유용성을 확인하도록 한다.